blob: a7c629286313d768dc9e36436229726d363e13f5 [file] [log] [blame]
/*
* Copyright (C) 2013 Samsung Electronics
*
* Configuration settings for the SAMSUNG EXYNOS5 board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_SAMSUNG /* in a SAMSUNG core */
#define CONFIG_S5P /* S5P Family */
#define CONFIG_EXYNOS5 /* which is in a Exynos5 Family */
#include <asm/arch/cpu.h> /* get chip and board defs */
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_BOARD_COMMON
#define CONFIG_ARCH_EARLY_INIT_R
#define CONFIG_EXYNOS_SPL
/* Enable fdt support for Exynos5250 */
#define CONFIG_OF_CONTROL
#define CONFIG_OF_SEPARATE
/* Allow tracing to be enabled */
#define CONFIG_TRACE
#define CONFIG_CMD_TRACE
#define CONFIG_TRACE_BUFFER_SIZE (16 << 20)
#define CONFIG_TRACE_EARLY_SIZE (8 << 20)
#define CONFIG_TRACE_EARLY
#define CONFIG_TRACE_EARLY_ADDR 0x50000000
/* Keep L2 Cache Disabled */
#define CONFIG_SYS_DCACHE_OFF
#define CONFIG_SYS_CACHELINE_SIZE 64
/* Enable ACE acceleration for SHA1 and SHA256 */
#define CONFIG_EXYNOS_ACE_SHA
#define CONFIG_SHA_HW_ACCEL
/* input clock of PLL: SMDK5250 has 24MHz input clock */
#define CONFIG_SYS_CLK_FREQ 24000000
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_CMDLINE_TAG
#define CONFIG_INITRD_TAG
#define CONFIG_CMDLINE_EDITING
/* Power Down Modes */
#define S5P_CHECK_SLEEP 0x00000BAD
#define S5P_CHECK_DIDLE 0xBAD00000
#define S5P_CHECK_LPA 0xABAD0000
/* Offset for inform registers */
#define INFORM0_OFFSET 0x800
#define INFORM1_OFFSET 0x804
#define INFORM2_OFFSET 0x808
#define INFORM3_OFFSET 0x80c
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20))
/* select serial console configuration */
#define CONFIG_BAUDRATE 115200
#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000
#define CONFIG_SILENT_CONSOLE
/* Enable keyboard */
#define CONFIG_CROS_EC /* CROS_EC protocol */
#define CONFIG_CROS_EC_SPI /* Support CROS_EC over SPI */
#define CONFIG_CROS_EC_I2C /* Support CROS_EC over I2C */
#define CONFIG_CROS_EC_KEYB /* CROS_EC keyboard input */
#define CONFIG_CMD_CROS_EC
#define CONFIG_KEYBOARD
/* Console configuration */
#define CONFIG_CONSOLE_MUX
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define EXYNOS_DEVICE_SETTINGS \
"stdin=serial,cros-ec-keyb\0" \
"stdout=serial,lcd\0" \
"stderr=serial,lcd\0"
#define CONFIG_EXTRA_ENV_SETTINGS \
EXYNOS_DEVICE_SETTINGS
/* SD/MMC configuration */
#define CONFIG_GENERIC_MMC
#define CONFIG_MMC
#define CONFIG_SDHCI
#define CONFIG_S5P_SDHCI
#define CONFIG_DWMMC
#define CONFIG_EXYNOS_DWMMC
#define CONFIG_SUPPORT_EMMC_BOOT
#define CONFIG_BOUNCE_BUFFER
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_SKIP_LOWLEVEL_INIT
/* PWM */
#define CONFIG_PWM
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
/* Command definition*/
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_ELF
#define CONFIG_CMD_MMC
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_NET
#define CONFIG_CMD_HASH
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK
/* Thermal Management Unit */
#define CONFIG_EXYNOS_TMU
#define CONFIG_CMD_DTT
#define CONFIG_TMU_CMD_DTT
/* TPM */
#define CONFIG_TPM
#define CONFIG_CMD_TPM
#define CONFIG_TPM_TIS_I2C
#define CONFIG_TPM_TIS_I2C_BUS_NUMBER 3
#define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20
/* MMC SPL */
#define COPY_BL2_FNPTR_ADDR 0x02020030
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
/* specific .lds file */
#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE 384 /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0"
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000)
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000)
#define CONFIG_RD_LVL
#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE
#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE
#define CONFIG_SYS_MONITOR_BASE 0x00000000
/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH
#undef CONFIG_CMD_IMLS
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_SECURE_BL1_ONLY
/* Secure FW size configuration */
#ifdef CONFIG_SECURE_BL1_ONLY
#define CONFIG_SEC_FW_SIZE (8 << 10) /* 8KB */
#else
#define CONFIG_SEC_FW_SIZE 0
#endif
/* Configuration of BL1, BL2, ENV Blocks on mmc */
#define CONFIG_RES_BLOCK_SIZE (512)
#define CONFIG_BL1_SIZE (16 << 10) /*16 K reserved for BL1*/
#define CONFIG_BL2_SIZE (512UL << 10UL) /* 512 KB */
#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */
#define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
#define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
/* Store environment at the end of a 4 MB SPI flash */
#define FLASH_SIZE (0x4 << 20)
#define CONFIG_ENV_OFFSET (FLASH_SIZE - CONFIG_BL2_SIZE)
/* U-boot copy size from boot Media to DRAM.*/
#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512)
#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512)
#define CONFIG_SPI_BOOTING
#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058
#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
#define CONFIG_DOS_PARTITION
#define CONFIG_EFI_PARTITION
#define CONFIG_CMD_PART
#define CONFIG_PARTITION_UUIDS
/* I2C */
#define CONFIG_SYS_I2C_INIT_BOARD
#define CONFIG_SYS_I2C
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */
#define CONFIG_SYS_I2C_S3C24X0
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0
#define CONFIG_I2C_EDID
/* SPI */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_SPI_FLASH
#define CONFIG_ENV_SPI_BASE 0x12D30000
#ifdef CONFIG_SPI_FLASH
#define CONFIG_EXYNOS_SPI
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
#define CONFIG_SPI_FLASH_WINBOND
#define CONFIG_SPI_FLASH_GIGADEVICE
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#define CONFIG_SF_DEFAULT_SPEED 50000000
#define EXYNOS5_SPI_NUM_CONTROLLERS 5
#define CONFIG_OF_SPI
#endif
#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_MODE SPI_MODE_0
#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
#define CONFIG_ENV_SPI_BUS 1
#define CONFIG_ENV_SPI_MAX_HZ 50000000
#endif
/* PMIC */
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_TPS65090
/* Ethernet Controllor Driver */
#ifdef CONFIG_CMD_NET
#define CONFIG_SMC911X
#define CONFIG_SMC911X_BASE 0x5000000
#define CONFIG_SMC911X_16_BIT
#define CONFIG_ENV_SROM_BANK 1
#endif /*CONFIG_CMD_NET*/
/* Enable PXE Support */
#ifdef CONFIG_CMD_NET
#define CONFIG_CMD_PXE
#define CONFIG_MENU
#endif
/* Enable devicetree support */
#define CONFIG_OF_LIBFDT
/* SHA hashing */
#define CONFIG_CMD_HASH
#define CONFIG_HASH_VERIFY
#define CONFIG_SHA1
#define CONFIG_SHA256
/* Enable Time Command */
#define CONFIG_CMD_TIME
#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_GPIO
/* USB boot mode */
#define CONFIG_USB_BOOTING
#define EXYNOS_COPY_USB_FNPTR_ADDR 0x02020070
#define EXYNOS_USB_SECONDARY_BOOT 0xfeed0002
#define EXYNOS_IRAM_SECONDARY_BASE 0x02020018
#endif /* __CONFIG_H */