drivers/i2c/mxs_i2c.c - github/trini/u-boot - Gitiles

 /*
  * Freescale i.MX28 I2C Driver
  *
  * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
  * on behalf of DENX Software Engineering GmbH
  *
  * Partly based on Linux kernel i2c-mxs.c driver:
  * Copyright (C) 2011 Wolfram Sang, Pengutronix e.K.
  *
  * Which was based on a (non-working) driver which was:
  * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #include <common.h>
 #include <malloc.h>
 #include <i2c.h>
 #include <asm/errno.h>
 #include <asm/io.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/sys_proto.h>

 #define	MXS_I2C_MAX_TIMEOUT	1000000

 static struct mxs_i2c_regs *mxs_i2c_get_base(struct i2c_adapter *adap)
 {
 	if (adap->hwadapnr == 0)
 		return (struct mxs_i2c_regs *)MXS_I2C0_BASE;
 	else
 		return (struct mxs_i2c_regs *)MXS_I2C1_BASE;
 }

 static unsigned int mxs_i2c_get_bus_speed(struct i2c_adapter *adap)
 {
 	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
 	uint32_t clk = mxc_get_clock(MXC_XTAL_CLK);
 	uint32_t timing0;

 	timing0 = readl(&i2c_regs->hw_i2c_timing0);
 	/*
 	 * This is a reverse version of the algorithm presented in
 	 * i2c_set_bus_speed(). Please refer there for details.
 	 */
 	return clk / ((((timing0 >> 16) - 3) * 2) + 38);
 }

 static uint mxs_i2c_set_bus_speed(struct i2c_adapter *adap, uint speed)
 {
 	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
 	/*
 	 * The timing derivation algorithm. There is no documentation for this
 	 * algorithm available, it was derived by using the scope and fiddling
 	 * with constants until the result observed on the scope was good enough
 	 * for 20kHz, 50kHz, 100kHz, 200kHz, 300kHz and 400kHz. It should be
 	 * possible to assume the algorithm works for other frequencies as well.
 	 *
 	 * Note it was necessary to cap the frequency on both ends as it's not
 	 * possible to configure completely arbitrary frequency for the I2C bus
 	 * clock.
 	 */
 	uint32_t clk = mxc_get_clock(MXC_XTAL_CLK);
 	uint32_t base = ((clk / speed) - 38) / 2;
 	uint16_t high_count = base + 3;
 	uint16_t low_count = base - 3;
 	uint16_t rcv_count = (high_count * 3) / 4;
 	uint16_t xmit_count = low_count / 4;

 	if (speed > 540000) {
 		printf("MXS I2C: Speed too high (%d Hz)\n", speed);
 		return -EINVAL;
 	}

 	if (speed < 12000) {
 		printf("MXS I2C: Speed too low (%d Hz)\n", speed);
 		return -EINVAL;
 	}

 	writel((high_count << 16) | rcv_count, &i2c_regs->hw_i2c_timing0);
 	writel((low_count << 16) | xmit_count, &i2c_regs->hw_i2c_timing1);

 	writel((0x0030 << I2C_TIMING2_BUS_FREE_OFFSET) |
 		(0x0030 << I2C_TIMING2_LEADIN_COUNT_OFFSET),
 		&i2c_regs->hw_i2c_timing2);

 	return 0;
 }

 static void mxs_i2c_reset(struct i2c_adapter *adap)
 {
 	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
 	int ret;
 	int speed = mxs_i2c_get_bus_speed(adap);

 	ret = mxs_reset_block(&i2c_regs->hw_i2c_ctrl0_reg);
 	if (ret) {
 		debug("MXS I2C: Block reset timeout\n");
 		return;
 	}

 	writel(I2C_CTRL1_DATA_ENGINE_CMPLT_IRQ | I2C_CTRL1_NO_SLAVE_ACK_IRQ |
 		I2C_CTRL1_EARLY_TERM_IRQ | I2C_CTRL1_MASTER_LOSS_IRQ |
 		I2C_CTRL1_SLAVE_STOP_IRQ | I2C_CTRL1_SLAVE_IRQ,
 		&i2c_regs->hw_i2c_ctrl1_clr);

 	writel(I2C_QUEUECTRL_PIO_QUEUE_MODE, &i2c_regs->hw_i2c_queuectrl_set);

 	mxs_i2c_set_bus_speed(adap, speed);
 }

 static void mxs_i2c_setup_read(struct i2c_adapter *adap, uint8_t chip, int len)
 {
 	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);

 	writel(I2C_QUEUECMD_RETAIN_CLOCK | I2C_QUEUECMD_PRE_SEND_START |
 		I2C_QUEUECMD_MASTER_MODE | I2C_QUEUECMD_DIRECTION |
 		(1 << I2C_QUEUECMD_XFER_COUNT_OFFSET),
 		&i2c_regs->hw_i2c_queuecmd);

 	writel((chip << 1) | 1, &i2c_regs->hw_i2c_data);

 	writel(I2C_QUEUECMD_SEND_NAK_ON_LAST | I2C_QUEUECMD_MASTER_MODE |
 		(len << I2C_QUEUECMD_XFER_COUNT_OFFSET) |
 		I2C_QUEUECMD_POST_SEND_STOP, &i2c_regs->hw_i2c_queuecmd);

 	writel(I2C_QUEUECTRL_QUEUE_RUN, &i2c_regs->hw_i2c_queuectrl_set);
 }

 static int mxs_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
 			 int alen, uchar *buf, int blen, int stop)
 {
 	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
 	uint32_t data, tmp;
 	int i, remain, off;
 	int timeout = MXS_I2C_MAX_TIMEOUT;

 	if ((alen > 4) || (alen == 0)) {
 		debug("MXS I2C: Invalid address length\n");
 		return -EINVAL;
 	}

 	if (stop)
 		stop = I2C_QUEUECMD_POST_SEND_STOP;

 	writel(I2C_QUEUECMD_PRE_SEND_START |
 		I2C_QUEUECMD_MASTER_MODE | I2C_QUEUECMD_DIRECTION |
 		((blen + alen + 1) << I2C_QUEUECMD_XFER_COUNT_OFFSET) | stop,
 		&i2c_regs->hw_i2c_queuecmd);

 	data = (chip << 1) << 24;

 	for (i = 0; i < alen; i++) {
 		data >>= 8;
 		data |= ((char *)&addr)[alen - i - 1] << 24;
 		if ((i & 3) == 2)
 			writel(data, &i2c_regs->hw_i2c_data);
 	}

 	off = i;
 	for (; i < off + blen; i++) {
 		data >>= 8;
 		data |= buf[i - off] << 24;
 		if ((i & 3) == 2)
 			writel(data, &i2c_regs->hw_i2c_data);
 	}

 	remain = 24 - ((i & 3) * 8);
 	if (remain)
 		writel(data >> remain, &i2c_regs->hw_i2c_data);

 	writel(I2C_QUEUECTRL_QUEUE_RUN, &i2c_regs->hw_i2c_queuectrl_set);

 	while (--timeout) {
 		tmp = readl(&i2c_regs->hw_i2c_queuestat);
 		if (tmp & I2C_QUEUESTAT_WR_QUEUE_EMPTY)
 			break;
 	}

 	if (!timeout) {
 		debug("MXS I2C: Failed transmitting data!\n");
 		return -EINVAL;
 	}

 	return 0;
 }

 static int mxs_i2c_wait_for_ack(struct i2c_adapter *adap)
 {
 	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
 	uint32_t tmp;
 	int timeout = MXS_I2C_MAX_TIMEOUT;

 	for (;;) {
 		tmp = readl(&i2c_regs->hw_i2c_ctrl1);
 		if (tmp & I2C_CTRL1_NO_SLAVE_ACK_IRQ) {
 			debug("MXS I2C: No slave ACK\n");
 			goto err;
 		}

 		if (tmp & (
 			I2C_CTRL1_EARLY_TERM_IRQ | I2C_CTRL1_MASTER_LOSS_IRQ |
 			I2C_CTRL1_SLAVE_STOP_IRQ | I2C_CTRL1_SLAVE_IRQ)) {
 			debug("MXS I2C: Error (CTRL1 = %08x)\n", tmp);
 			goto err;
 		}

 		if (tmp & I2C_CTRL1_DATA_ENGINE_CMPLT_IRQ)
 			break;

 		if (!timeout--) {
 			debug("MXS I2C: Operation timed out\n");
 			goto err;
 		}

 		udelay(1);
 	}

 	return 0;

 err:
 	mxs_i2c_reset(adap);
 	return 1;
 }

 static int mxs_i2c_if_read(struct i2c_adapter *adap, uint8_t chip,
 			   uint addr, int alen, uint8_t *buffer,
 			   int len)
 {
 	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
 	uint32_t tmp = 0;
 	int timeout = MXS_I2C_MAX_TIMEOUT;
 	int ret;
 	int i;

 	ret = mxs_i2c_write(adap, chip, addr, alen, NULL, 0, 0);
 	if (ret) {
 		debug("MXS I2C: Failed writing address\n");
 		return ret;
 	}

 	ret = mxs_i2c_wait_for_ack(adap);
 	if (ret) {
 		debug("MXS I2C: Failed writing address\n");
 		return ret;
 	}

 	mxs_i2c_setup_read(adap, chip, len);
 	ret = mxs_i2c_wait_for_ack(adap);
 	if (ret) {
 		debug("MXS I2C: Failed reading address\n");
 		return ret;
 	}

 	for (i = 0; i < len; i++) {
 		if (!(i & 3)) {
 			while (--timeout) {
 				tmp = readl(&i2c_regs->hw_i2c_queuestat);
 				if (!(tmp & I2C_QUEUESTAT_RD_QUEUE_EMPTY))
 					break;
 			}

 			if (!timeout) {
 				debug("MXS I2C: Failed receiving data!\n");
 				return -ETIMEDOUT;
 			}

 			tmp = readl(&i2c_regs->hw_i2c_queuedata);
 		}
 		buffer[i] = tmp & 0xff;
 		tmp >>= 8;
 	}

 	return 0;
 }

 static int mxs_i2c_if_write(struct i2c_adapter *adap, uint8_t chip,
 			    uint addr, int alen, uint8_t *buffer,
 			    int len)
 {
 	int ret;
 	ret = mxs_i2c_write(adap, chip, addr, alen, buffer, len, 1);
 	if (ret) {
 		debug("MXS I2C: Failed writing address\n");
 		return ret;
 	}

 	ret = mxs_i2c_wait_for_ack(adap);
 	if (ret)
 		debug("MXS I2C: Failed writing address\n");

 	return ret;
 }

 static int mxs_i2c_probe(struct i2c_adapter *adap, uint8_t chip)
 {
 	int ret;
 	ret = mxs_i2c_write(adap, chip, 0, 1, NULL, 0, 1);
 	if (!ret)
 		ret = mxs_i2c_wait_for_ack(adap);
 	mxs_i2c_reset(adap);
 	return ret;
 }

 static void mxs_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
 {
 	mxs_i2c_reset(adap);
 	mxs_i2c_set_bus_speed(adap, speed);

 	return;
 }

 U_BOOT_I2C_ADAP_COMPLETE(mxs0, mxs_i2c_init, mxs_i2c_probe,
 			 mxs_i2c_if_read, mxs_i2c_if_write,
 			 mxs_i2c_set_bus_speed,
 			 CONFIG_SYS_I2C_SPEED, 0, 0)
 U_BOOT_I2C_ADAP_COMPLETE(mxs1, mxs_i2c_init, mxs_i2c_probe,
 			 mxs_i2c_if_read, mxs_i2c_if_write,
 			 mxs_i2c_set_bus_speed,
 			 CONFIG_SYS_I2C_SPEED, 0, 1)
	/*
	* Freescale i.MX28 I2C Driver
	*
	* Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
	* on behalf of DENX Software Engineering GmbH
	*
	* Partly based on Linux kernel i2c-mxs.c driver:
	* Copyright (C) 2011 Wolfram Sang, Pengutronix e.K.
	*
	* Which was based on a (non-working) driver which was:
	* Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#include <common.h>
	#include <malloc.h>
	#include <i2c.h>
	#include <asm/errno.h>
	#include <asm/io.h>
	#include <asm/arch/clock.h>
	#include <asm/arch/imx-regs.h>
	#include <asm/arch/sys_proto.h>

	#define MXS_I2C_MAX_TIMEOUT 1000000

	static struct mxs_i2c_regs mxs_i2c_get_base(struct i2c_adapter adap)
	{
	if (adap->hwadapnr == 0)
	return (struct mxs_i2c_regs *)MXS_I2C0_BASE;
	else
	return (struct mxs_i2c_regs *)MXS_I2C1_BASE;
	}

	static unsigned int mxs_i2c_get_bus_speed(struct i2c_adapter *adap)
	{
	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
	uint32_t clk = mxc_get_clock(MXC_XTAL_CLK);
	uint32_t timing0;

	timing0 = readl(&i2c_regs->hw_i2c_timing0);
	/*
	* This is a reverse version of the algorithm presented in
	* i2c_set_bus_speed(). Please refer there for details.
	*/
	return clk / ((((timing0 >> 16) - 3) * 2) + 38);
	}

	static uint mxs_i2c_set_bus_speed(struct i2c_adapter *adap, uint speed)
	{
	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
	/*
	* The timing derivation algorithm. There is no documentation for this
	* algorithm available, it was derived by using the scope and fiddling
	* with constants until the result observed on the scope was good enough
	* for 20kHz, 50kHz, 100kHz, 200kHz, 300kHz and 400kHz. It should be
	* possible to assume the algorithm works for other frequencies as well.
	*
	* Note it was necessary to cap the frequency on both ends as it's not
	* possible to configure completely arbitrary frequency for the I2C bus
	* clock.
	*/
	uint32_t clk = mxc_get_clock(MXC_XTAL_CLK);
	uint32_t base = ((clk / speed) - 38) / 2;
	uint16_t high_count = base + 3;
	uint16_t low_count = base - 3;
	uint16_t rcv_count = (high_count * 3) / 4;
	uint16_t xmit_count = low_count / 4;

	if (speed > 540000) {
	printf("MXS I2C: Speed too high (%d Hz)\n", speed);
	return -EINVAL;
	}

	if (speed < 12000) {
	printf("MXS I2C: Speed too low (%d Hz)\n", speed);
	return -EINVAL;
	}

	writel((high_count << 16) \| rcv_count, &i2c_regs->hw_i2c_timing0);
	writel((low_count << 16) \| xmit_count, &i2c_regs->hw_i2c_timing1);

	writel((0x0030 << I2C_TIMING2_BUS_FREE_OFFSET) \|
	(0x0030 << I2C_TIMING2_LEADIN_COUNT_OFFSET),
	&i2c_regs->hw_i2c_timing2);

	return 0;
	}

	static void mxs_i2c_reset(struct i2c_adapter *adap)
	{
	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
	int ret;
	int speed = mxs_i2c_get_bus_speed(adap);

	ret = mxs_reset_block(&i2c_regs->hw_i2c_ctrl0_reg);
	if (ret) {
	debug("MXS I2C: Block reset timeout\n");
	return;
	}

	writel(I2C_CTRL1_DATA_ENGINE_CMPLT_IRQ \| I2C_CTRL1_NO_SLAVE_ACK_IRQ \|
	I2C_CTRL1_EARLY_TERM_IRQ \| I2C_CTRL1_MASTER_LOSS_IRQ \|
	I2C_CTRL1_SLAVE_STOP_IRQ \| I2C_CTRL1_SLAVE_IRQ,
	&i2c_regs->hw_i2c_ctrl1_clr);

	writel(I2C_QUEUECTRL_PIO_QUEUE_MODE, &i2c_regs->hw_i2c_queuectrl_set);

	mxs_i2c_set_bus_speed(adap, speed);
	}

	static void mxs_i2c_setup_read(struct i2c_adapter *adap, uint8_t chip, int len)
	{
	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);

	writel(I2C_QUEUECMD_RETAIN_CLOCK \| I2C_QUEUECMD_PRE_SEND_START \|
	I2C_QUEUECMD_MASTER_MODE \| I2C_QUEUECMD_DIRECTION \|
	(1 << I2C_QUEUECMD_XFER_COUNT_OFFSET),
	&i2c_regs->hw_i2c_queuecmd);

	writel((chip << 1) \| 1, &i2c_regs->hw_i2c_data);

	writel(I2C_QUEUECMD_SEND_NAK_ON_LAST \| I2C_QUEUECMD_MASTER_MODE \|
	(len << I2C_QUEUECMD_XFER_COUNT_OFFSET) \|
	I2C_QUEUECMD_POST_SEND_STOP, &i2c_regs->hw_i2c_queuecmd);

	writel(I2C_QUEUECTRL_QUEUE_RUN, &i2c_regs->hw_i2c_queuectrl_set);
	}

	static int mxs_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
	int alen, uchar *buf, int blen, int stop)
	{
	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
	uint32_t data, tmp;
	int i, remain, off;
	int timeout = MXS_I2C_MAX_TIMEOUT;

	if ((alen > 4) \|\| (alen == 0)) {
	debug("MXS I2C: Invalid address length\n");
	return -EINVAL;
	}

	if (stop)
	stop = I2C_QUEUECMD_POST_SEND_STOP;

	writel(I2C_QUEUECMD_PRE_SEND_START \|
	I2C_QUEUECMD_MASTER_MODE \| I2C_QUEUECMD_DIRECTION \|
	((blen + alen + 1) << I2C_QUEUECMD_XFER_COUNT_OFFSET) \| stop,
	&i2c_regs->hw_i2c_queuecmd);

	data = (chip << 1) << 24;

	for (i = 0; i < alen; i++) {
	data >>= 8;
	data \|= ((char *)&addr)[alen - i - 1] << 24;
	if ((i & 3) == 2)
	writel(data, &i2c_regs->hw_i2c_data);
	}

	off = i;
	for (; i < off + blen; i++) {
	data >>= 8;
	data \|= buf[i - off] << 24;
	if ((i & 3) == 2)
	writel(data, &i2c_regs->hw_i2c_data);
	}

	remain = 24 - ((i & 3) * 8);
	if (remain)
	writel(data >> remain, &i2c_regs->hw_i2c_data);

	writel(I2C_QUEUECTRL_QUEUE_RUN, &i2c_regs->hw_i2c_queuectrl_set);

	while (--timeout) {
	tmp = readl(&i2c_regs->hw_i2c_queuestat);
	if (tmp & I2C_QUEUESTAT_WR_QUEUE_EMPTY)
	break;
	}

	if (!timeout) {
	debug("MXS I2C: Failed transmitting data!\n");
	return -EINVAL;
	}

	return 0;
	}

	static int mxs_i2c_wait_for_ack(struct i2c_adapter *adap)
	{
	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
	uint32_t tmp;
	int timeout = MXS_I2C_MAX_TIMEOUT;

	for (;;) {
	tmp = readl(&i2c_regs->hw_i2c_ctrl1);
	if (tmp & I2C_CTRL1_NO_SLAVE_ACK_IRQ) {
	debug("MXS I2C: No slave ACK\n");
	goto err;
	}

	if (tmp & (
	I2C_CTRL1_EARLY_TERM_IRQ \| I2C_CTRL1_MASTER_LOSS_IRQ \|
	I2C_CTRL1_SLAVE_STOP_IRQ \| I2C_CTRL1_SLAVE_IRQ)) {
	debug("MXS I2C: Error (CTRL1 = %08x)\n", tmp);
	goto err;
	}

	if (tmp & I2C_CTRL1_DATA_ENGINE_CMPLT_IRQ)
	break;

	if (!timeout--) {
	debug("MXS I2C: Operation timed out\n");
	goto err;
	}

	udelay(1);
	}

	return 0;

	err:
	mxs_i2c_reset(adap);
	return 1;
	}

	static int mxs_i2c_if_read(struct i2c_adapter *adap, uint8_t chip,
	uint addr, int alen, uint8_t *buffer,
	int len)
	{
	struct mxs_i2c_regs *i2c_regs = mxs_i2c_get_base(adap);
	uint32_t tmp = 0;
	int timeout = MXS_I2C_MAX_TIMEOUT;
	int ret;
	int i;

	ret = mxs_i2c_write(adap, chip, addr, alen, NULL, 0, 0);
	if (ret) {
	debug("MXS I2C: Failed writing address\n");
	return ret;
	}

	ret = mxs_i2c_wait_for_ack(adap);
	if (ret) {
	debug("MXS I2C: Failed writing address\n");
	return ret;
	}

	mxs_i2c_setup_read(adap, chip, len);
	ret = mxs_i2c_wait_for_ack(adap);
	if (ret) {
	debug("MXS I2C: Failed reading address\n");
	return ret;
	}

	for (i = 0; i < len; i++) {
	if (!(i & 3)) {
	while (--timeout) {
	tmp = readl(&i2c_regs->hw_i2c_queuestat);
	if (!(tmp & I2C_QUEUESTAT_RD_QUEUE_EMPTY))
	break;
	}

	if (!timeout) {
	debug("MXS I2C: Failed receiving data!\n");
	return -ETIMEDOUT;
	}

	tmp = readl(&i2c_regs->hw_i2c_queuedata);
	}
	buffer[i] = tmp & 0xff;
	tmp >>= 8;
	}

	return 0;
	}

	static int mxs_i2c_if_write(struct i2c_adapter *adap, uint8_t chip,
	uint addr, int alen, uint8_t *buffer,
	int len)
	{
	int ret;
	ret = mxs_i2c_write(adap, chip, addr, alen, buffer, len, 1);
	if (ret) {
	debug("MXS I2C: Failed writing address\n");
	return ret;
	}

	ret = mxs_i2c_wait_for_ack(adap);
	if (ret)
	debug("MXS I2C: Failed writing address\n");

	return ret;
	}

	static int mxs_i2c_probe(struct i2c_adapter *adap, uint8_t chip)
	{
	int ret;
	ret = mxs_i2c_write(adap, chip, 0, 1, NULL, 0, 1);
	if (!ret)
	ret = mxs_i2c_wait_for_ack(adap);
	mxs_i2c_reset(adap);
	return ret;
	}

	static void mxs_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
	{
	mxs_i2c_reset(adap);
	mxs_i2c_set_bus_speed(adap, speed);

	return;
	}

	U_BOOT_I2C_ADAP_COMPLETE(mxs0, mxs_i2c_init, mxs_i2c_probe,
	mxs_i2c_if_read, mxs_i2c_if_write,
	mxs_i2c_set_bus_speed,
	CONFIG_SYS_I2C_SPEED, 0, 0)
	U_BOOT_I2C_ADAP_COMPLETE(mxs1, mxs_i2c_init, mxs_i2c_probe,
	mxs_i2c_if_read, mxs_i2c_if_write,
	mxs_i2c_set_bus_speed,
	CONFIG_SYS_I2C_SPEED, 0, 1)