board/inka4x0/inka4x0.c - github/trini/u-boot - Gitiles

 /*
  * (C) Copyright 2008-2009
  * Andreas Pfefferle, DENX Software Engineering, ap@denx.de.
  *
  * (C) Copyright 2009
  * Detlev Zundel, DENX Software Engineering, dzu@denx.de.
  *
  * (C) Copyright 2004
  * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
  *
  * (C) Copyright 2004
  * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
  *
  * (C) Copyright 2003-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #include <asm/io.h>
 #include <common.h>
 #include <mpc5xxx.h>
 #include <pci.h>

 #if defined(CONFIG_DDR_MT46V16M16)
 #include "mt46v16m16-75.h"
 #elif defined(CONFIG_SDR_MT48LC16M16A2)
 #include "mt48lc16m16a2-75.h"
 #elif defined(CONFIG_DDR_MT46V32M16)
 #include "mt46v32m16.h"
 #elif defined(CONFIG_DDR_HYB25D512160BF)
 #include "hyb25d512160bf.h"
 #elif defined(CONFIG_DDR_K4H511638C)
 #include "k4h511638c.h"
 #else
 #error "INKA4x0 SDRAM: invalid chip type specified!"
 #endif

 #ifndef CONFIG_SYS_RAMBOOT
 static void sdram_start (int hi_addr)
 {
 	volatile struct mpc5xxx_sdram *sdram =
 		(struct mpc5xxx_sdram *)MPC5XXX_SDRAM;
 	long hi_addr_bit = hi_addr ? 0x01000000 : 0;

 	/* unlock mode register */
 	out_be32(&sdram->ctrl, SDRAM_CONTROL | 0x80000000 | hi_addr_bit);

 	/* precharge all banks */
 	out_be32(&sdram->ctrl, SDRAM_CONTROL | 0x80000002 | hi_addr_bit);

 #if SDRAM_DDR
 	/* set mode register: extended mode */
 	out_be32(&sdram->mode, SDRAM_EMODE);

 	/* set mode register: reset DLL */
 	out_be32(&sdram->mode, SDRAM_MODE | 0x04000000);
 #endif

 	/* precharge all banks */
 	out_be32(&sdram->ctrl, SDRAM_CONTROL | 0x80000002 | hi_addr_bit);

 	/* auto refresh */
 	out_be32(&sdram->ctrl, SDRAM_CONTROL | 0x80000004 | hi_addr_bit);

 	/* set mode register */
 	out_be32(&sdram->mode, SDRAM_MODE);

 	/* normal operation */
 	out_be32(&sdram->ctrl, SDRAM_CONTROL | hi_addr_bit);
 }
 #endif

 /*
  * ATTENTION: Although partially referenced initdram does NOT make real use
  *	      use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
  *	      is something else than 0x00000000.
  */

 phys_size_t initdram (int board_type)
 {
 	volatile struct mpc5xxx_mmap_ctl *mm =
 		(struct mpc5xxx_mmap_ctl *) CONFIG_SYS_MBAR;
 	volatile struct mpc5xxx_cdm     *cdm =
 		(struct mpc5xxx_cdm *)      MPC5XXX_CDM;
 	volatile struct mpc5xxx_sdram *sdram =
 		(struct mpc5xxx_sdram *)    MPC5XXX_SDRAM;
 	ulong dramsize = 0;
 #ifndef CONFIG_SYS_RAMBOOT
 	long test1, test2;

 	/* setup SDRAM chip selects */
 	out_be32(&mm->sdram0, 0x0000001c);	/* 512MB at 0x0 */
 	out_be32(&mm->sdram1, 0x40000000);	/* disabled */

 	/* setup config registers */
 	out_be32(&sdram->config1, SDRAM_CONFIG1);
 	out_be32(&sdram->config2, SDRAM_CONFIG2);

 #if SDRAM_DDR
 	/* set tap delay */
 	out_be32(&cdm->porcfg, SDRAM_TAPDELAY);
 #endif

 	/* find RAM size using SDRAM CS0 only */
 	sdram_start(0);
 	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000);
 	sdram_start(1);
 	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000);
 	if (test1 > test2) {
 		sdram_start(0);
 		dramsize = test1;
 	} else {
 		dramsize = test2;
 	}

 	/* memory smaller than 1MB is impossible */
 	if (dramsize < (1 << 20)) {
 		dramsize = 0;
 	}

 	/* set SDRAM CS0 size according to the amount of RAM found */
 	if (dramsize > 0) {
 		out_be32(&mm->sdram0, 0x13 +
 			 __builtin_ffs(dramsize >> 20) - 1);
 	} else {
 		out_be32(&mm->sdram0, 0); /* disabled */
 	}

 	out_be32(&mm->sdram1, dramsize); /* disabled */
 #else /* CONFIG_SYS_RAMBOOT */

 	/* retrieve size of memory connected to SDRAM CS0 */
 	dramsize = in_be32(&mm->sdram0) & 0xFF;
 	if (dramsize >= 0x13) {
 		dramsize = (1 << (dramsize - 0x13)) << 20;
 	} else {
 		dramsize = 0;
 	}
 #endif /* CONFIG_SYS_RAMBOOT */

 	return dramsize;
 }

 int checkboard (void)
 {
 	puts ("Board: INKA 4X0\n");
 	return 0;
 }

 void flash_preinit(void)
 {
 	volatile struct mpc5xxx_lpb *lpb = (struct mpc5xxx_lpb *)MPC5XXX_LPB;

 	/*
 	 * Now, when we are in RAM, enable flash write
 	 * access for detection process.
 	 * Note that CS_BOOT (CS0) cannot be cleared when
 	 * executing in flash.
 	 */
 	clrbits_be32(&lpb->cs0_cfg, 0x1); /* clear RO */
 }

 int misc_init_f (void)
 {
 	volatile struct mpc5xxx_gpio	*gpio    =
 		(struct mpc5xxx_gpio *)   MPC5XXX_GPIO;
 	volatile struct mpc5xxx_wu_gpio	*wu_gpio =
 		(struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
 	volatile struct mpc5xxx_gpt	*gpt;
 	char tmp[10];
 	int i, br;

 	i = getenv_f("brightness", tmp, sizeof(tmp));
 	br = (i > 0)
 		? (int) simple_strtoul (tmp, NULL, 10)
 		: CONFIG_SYS_BRIGHTNESS;
 	if (br > 255)
 		br = 255;

 	/* Initialize GPIO output pins.
 	 */
 	/* Configure GPT as GPIO output (and set them as they control low-active LEDs */
 	for (i = 0; i <= 5; i++) {
 		gpt = (struct mpc5xxx_gpt *)(MPC5XXX_GPT + (i * 0x10));
 		out_be32(&gpt->emsr, 0x34);
 	}

 	/* Configure GPT7 as PWM timer, 1kHz, no ints. */
 	gpt = (struct mpc5xxx_gpt *)(MPC5XXX_GPT + (7 * 0x10));
 	out_be32(&gpt->emsr,  0);		/* Disable */
 	out_be32(&gpt->cir,   0x020000fe);
 	out_be32(&gpt->pwmcr, (br << 16));
 	out_be32(&gpt->emsr,  0x3);		/* Enable PWM mode and start */

 	/* Configure PSC3_6,7 as GPIO output */
 	setbits_be32(&gpio->simple_gpioe, MPC5XXX_GPIO_SIMPLE_PSC3_6 |
 					  MPC5XXX_GPIO_SIMPLE_PSC3_7);
 	setbits_be32(&gpio->simple_ddr,   MPC5XXX_GPIO_SIMPLE_PSC3_6 |
 					  MPC5XXX_GPIO_SIMPLE_PSC3_7);

 	/* Configure PSC3_9 and GPIO_WKUP6,7 as GPIO output */
 	setbits_8(&wu_gpio->enable,  MPC5XXX_GPIO_WKUP_6 |
 				     MPC5XXX_GPIO_WKUP_7 |
 				     MPC5XXX_GPIO_WKUP_PSC3_9);
 	setbits_8(&wu_gpio->ddr,     MPC5XXX_GPIO_WKUP_6 |
 				     MPC5XXX_GPIO_WKUP_7 |
 				     MPC5XXX_GPIO_WKUP_PSC3_9);

 	/* Set LR mirror bit because it is low-active */
 	setbits_8(&wu_gpio->dvo,     MPC5XXX_GPIO_WKUP_7);

 	/* Reset Coral-P graphics controller */
 	setbits_8(&wu_gpio->dvo,     MPC5XXX_GPIO_WKUP_PSC3_9);

 	/* Enable display backlight */
 	clrbits_8(&gpio->sint_inten, MPC5XXX_GPIO_SINT_PSC3_8);
 	setbits_8(&gpio->sint_gpioe, MPC5XXX_GPIO_SINT_PSC3_8);
 	setbits_8(&gpio->sint_ddr,   MPC5XXX_GPIO_SINT_PSC3_8);
 	setbits_8(&gpio->sint_dvo,   MPC5XXX_GPIO_SINT_PSC3_8);

 	/*
 	 * Configure three wire serial interface to RTC (PSC1_4,
 	 * PSC2_4, PSC3_4, PSC3_5)
 	 */
 	setbits_8(&wu_gpio->enable,  MPC5XXX_GPIO_WKUP_PSC1_4 |
 				     MPC5XXX_GPIO_WKUP_PSC2_4);
 	setbits_8(&wu_gpio->ddr,     MPC5XXX_GPIO_WKUP_PSC1_4 |
 				     MPC5XXX_GPIO_WKUP_PSC2_4);
 	clrbits_8(&wu_gpio->dvo,     MPC5XXX_GPIO_WKUP_PSC1_4);
 	clrbits_8(&gpio->sint_inten, MPC5XXX_GPIO_SINT_PSC3_4 |
 				     MPC5XXX_GPIO_SINT_PSC3_5);
 	setbits_8(&gpio->sint_gpioe, MPC5XXX_GPIO_SINT_PSC3_4 |
 				     MPC5XXX_GPIO_SINT_PSC3_5);
 	setbits_8(&gpio->sint_ddr,   MPC5XXX_GPIO_SINT_PSC3_5);
 	clrbits_8(&gpio->sint_dvo,   MPC5XXX_GPIO_SINT_PSC3_5);

 	return 0;
 }

 #ifdef	CONFIG_PCI
 static struct pci_controller hose;

 extern void pci_mpc5xxx_init(struct pci_controller *);

 void pci_init_board(void)
 {
 	pci_mpc5xxx_init(&hose);
 }
 #endif
	/*
	* (C) Copyright 2008-2009
	* Andreas Pfefferle, DENX Software Engineering, ap@denx.de.
	*
	* (C) Copyright 2009
	* Detlev Zundel, DENX Software Engineering, dzu@denx.de.
	*
	* (C) Copyright 2004
	* Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
	*
	* (C) Copyright 2004
	* Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
	*
	* (C) Copyright 2003-2004
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#include <asm/io.h>
	#include <common.h>
	#include <mpc5xxx.h>
	#include <pci.h>

	#if defined(CONFIG_DDR_MT46V16M16)
	#include "mt46v16m16-75.h"
	#elif defined(CONFIG_SDR_MT48LC16M16A2)
	#include "mt48lc16m16a2-75.h"
	#elif defined(CONFIG_DDR_MT46V32M16)
	#include "mt46v32m16.h"
	#elif defined(CONFIG_DDR_HYB25D512160BF)
	#include "hyb25d512160bf.h"
	#elif defined(CONFIG_DDR_K4H511638C)
	#include "k4h511638c.h"
	#else
	#error "INKA4x0 SDRAM: invalid chip type specified!"
	#endif

	#ifndef CONFIG_SYS_RAMBOOT
	static void sdram_start (int hi_addr)
	{
	volatile struct mpc5xxx_sdram *sdram =
	(struct mpc5xxx_sdram *)MPC5XXX_SDRAM;
	long hi_addr_bit = hi_addr ? 0x01000000 : 0;

	/* unlock mode register */
	out_be32(&sdram->ctrl, SDRAM_CONTROL \| 0x80000000 \| hi_addr_bit);

	/* precharge all banks */
	out_be32(&sdram->ctrl, SDRAM_CONTROL \| 0x80000002 \| hi_addr_bit);

	#if SDRAM_DDR
	/* set mode register: extended mode */
	out_be32(&sdram->mode, SDRAM_EMODE);

	/* set mode register: reset DLL */
	out_be32(&sdram->mode, SDRAM_MODE \| 0x04000000);
	#endif

	/* precharge all banks */
	out_be32(&sdram->ctrl, SDRAM_CONTROL \| 0x80000002 \| hi_addr_bit);

	/* auto refresh */
	out_be32(&sdram->ctrl, SDRAM_CONTROL \| 0x80000004 \| hi_addr_bit);

	/* set mode register */
	out_be32(&sdram->mode, SDRAM_MODE);

	/* normal operation */
	out_be32(&sdram->ctrl, SDRAM_CONTROL \| hi_addr_bit);
	}
	#endif

	/*
	* ATTENTION: Although partially referenced initdram does NOT make real use
	* use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
	* is something else than 0x00000000.
	*/

	phys_size_t initdram (int board_type)
	{
	volatile struct mpc5xxx_mmap_ctl *mm =
	(struct mpc5xxx_mmap_ctl *) CONFIG_SYS_MBAR;
	volatile struct mpc5xxx_cdm *cdm =
	(struct mpc5xxx_cdm *) MPC5XXX_CDM;
	volatile struct mpc5xxx_sdram *sdram =
	(struct mpc5xxx_sdram *) MPC5XXX_SDRAM;
	ulong dramsize = 0;
	#ifndef CONFIG_SYS_RAMBOOT
	long test1, test2;

	/* setup SDRAM chip selects */
	out_be32(&mm->sdram0, 0x0000001c); /* 512MB at 0x0 */
	out_be32(&mm->sdram1, 0x40000000); /* disabled */

	/* setup config registers */
	out_be32(&sdram->config1, SDRAM_CONFIG1);
	out_be32(&sdram->config2, SDRAM_CONFIG2);

	#if SDRAM_DDR
	/* set tap delay */
	out_be32(&cdm->porcfg, SDRAM_TAPDELAY);
	#endif

	/* find RAM size using SDRAM CS0 only */
	sdram_start(0);
	test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000);
	sdram_start(1);
	test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x20000000);
	if (test1 > test2) {
	sdram_start(0);
	dramsize = test1;
	} else {
	dramsize = test2;
	}

	/* memory smaller than 1MB is impossible */
	if (dramsize < (1 << 20)) {
	dramsize = 0;
	}

	/* set SDRAM CS0 size according to the amount of RAM found */
	if (dramsize > 0) {
	out_be32(&mm->sdram0, 0x13 +
	__builtin_ffs(dramsize >> 20) - 1);
	} else {
	out_be32(&mm->sdram0, 0); /* disabled */
	}

	out_be32(&mm->sdram1, dramsize); /* disabled */
	#else /* CONFIG_SYS_RAMBOOT */

	/* retrieve size of memory connected to SDRAM CS0 */
	dramsize = in_be32(&mm->sdram0) & 0xFF;
	if (dramsize >= 0x13) {
	dramsize = (1 << (dramsize - 0x13)) << 20;
	} else {
	dramsize = 0;
	}
	#endif /* CONFIG_SYS_RAMBOOT */

	return dramsize;
	}

	int checkboard (void)
	{
	puts ("Board: INKA 4X0\n");
	return 0;
	}

	void flash_preinit(void)
	{
	volatile struct mpc5xxx_lpb lpb = (struct mpc5xxx_lpb )MPC5XXX_LPB;

	/*
	* Now, when we are in RAM, enable flash write
	* access for detection process.
	* Note that CS_BOOT (CS0) cannot be cleared when
	* executing in flash.
	*/
	clrbits_be32(&lpb->cs0_cfg, 0x1); /* clear RO */
	}

	int misc_init_f (void)
	{
	volatile struct mpc5xxx_gpio *gpio =
	(struct mpc5xxx_gpio *) MPC5XXX_GPIO;
	volatile struct mpc5xxx_wu_gpio *wu_gpio =
	(struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
	volatile struct mpc5xxx_gpt *gpt;
	char tmp[10];
	int i, br;

	i = getenv_f("brightness", tmp, sizeof(tmp));
	br = (i > 0)
	? (int) simple_strtoul (tmp, NULL, 10)
	: CONFIG_SYS_BRIGHTNESS;
	if (br > 255)
	br = 255;

	/* Initialize GPIO output pins.
	*/
	/* Configure GPT as GPIO output (and set them as they control low-active LEDs */
	for (i = 0; i <= 5; i++) {
	gpt = (struct mpc5xxx_gpt )(MPC5XXX_GPT + (i 0x10));
	out_be32(&gpt->emsr, 0x34);
	}

	/* Configure GPT7 as PWM timer, 1kHz, no ints. */
	gpt = (struct mpc5xxx_gpt )(MPC5XXX_GPT + (7 0x10));
	out_be32(&gpt->emsr, 0); /* Disable */
	out_be32(&gpt->cir, 0x020000fe);
	out_be32(&gpt->pwmcr, (br << 16));
	out_be32(&gpt->emsr, 0x3); /* Enable PWM mode and start */

	/* Configure PSC3_6,7 as GPIO output */
	setbits_be32(&gpio->simple_gpioe, MPC5XXX_GPIO_SIMPLE_PSC3_6 \|
	MPC5XXX_GPIO_SIMPLE_PSC3_7);
	setbits_be32(&gpio->simple_ddr, MPC5XXX_GPIO_SIMPLE_PSC3_6 \|
	MPC5XXX_GPIO_SIMPLE_PSC3_7);

	/* Configure PSC3_9 and GPIO_WKUP6,7 as GPIO output */
	setbits_8(&wu_gpio->enable, MPC5XXX_GPIO_WKUP_6 \|
	MPC5XXX_GPIO_WKUP_7 \|
	MPC5XXX_GPIO_WKUP_PSC3_9);
	setbits_8(&wu_gpio->ddr, MPC5XXX_GPIO_WKUP_6 \|
	MPC5XXX_GPIO_WKUP_7 \|
	MPC5XXX_GPIO_WKUP_PSC3_9);

	/* Set LR mirror bit because it is low-active */
	setbits_8(&wu_gpio->dvo, MPC5XXX_GPIO_WKUP_7);

	/* Reset Coral-P graphics controller */
	setbits_8(&wu_gpio->dvo, MPC5XXX_GPIO_WKUP_PSC3_9);

	/* Enable display backlight */
	clrbits_8(&gpio->sint_inten, MPC5XXX_GPIO_SINT_PSC3_8);
	setbits_8(&gpio->sint_gpioe, MPC5XXX_GPIO_SINT_PSC3_8);
	setbits_8(&gpio->sint_ddr, MPC5XXX_GPIO_SINT_PSC3_8);
	setbits_8(&gpio->sint_dvo, MPC5XXX_GPIO_SINT_PSC3_8);

	/*
	* Configure three wire serial interface to RTC (PSC1_4,
	* PSC2_4, PSC3_4, PSC3_5)
	*/
	setbits_8(&wu_gpio->enable, MPC5XXX_GPIO_WKUP_PSC1_4 \|
	MPC5XXX_GPIO_WKUP_PSC2_4);
	setbits_8(&wu_gpio->ddr, MPC5XXX_GPIO_WKUP_PSC1_4 \|
	MPC5XXX_GPIO_WKUP_PSC2_4);
	clrbits_8(&wu_gpio->dvo, MPC5XXX_GPIO_WKUP_PSC1_4);
	clrbits_8(&gpio->sint_inten, MPC5XXX_GPIO_SINT_PSC3_4 \|
	MPC5XXX_GPIO_SINT_PSC3_5);
	setbits_8(&gpio->sint_gpioe, MPC5XXX_GPIO_SINT_PSC3_4 \|
	MPC5XXX_GPIO_SINT_PSC3_5);
	setbits_8(&gpio->sint_ddr, MPC5XXX_GPIO_SINT_PSC3_5);
	clrbits_8(&gpio->sint_dvo, MPC5XXX_GPIO_SINT_PSC3_5);

	return 0;
	}

	#ifdef CONFIG_PCI
	static struct pci_controller hose;

	extern void pci_mpc5xxx_init(struct pci_controller *);

	void pci_init_board(void)
	{
	pci_mpc5xxx_init(&hose);
	}
	#endif