blob: 732ddf836dffc1a97ec6302b74ca119ffe51e509 [file] [log] [blame]
/*
* SPI flash internal definitions
*
* Copyright (C) 2008 Atmel Corporation
* Copyright (C) 2013 Jagannadha Sutradharudu Teki, Xilinx Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _SF_INTERNAL_H_
#define _SF_INTERNAL_H_
#define SPI_FLASH_16MB_BOUN 0x1000000
/* SECT flags */
#define SECT_4K (1 << 1)
#define SECT_32K (1 << 2)
#define E_FSR (1 << 3)
/* Erase commands */
#define CMD_ERASE_4K 0x20
#define CMD_ERASE_32K 0x52
#define CMD_ERASE_CHIP 0xc7
#define CMD_ERASE_64K 0xd8
/* Write commands */
#define CMD_WRITE_STATUS 0x01
#define CMD_PAGE_PROGRAM 0x02
#define CMD_WRITE_DISABLE 0x04
#define CMD_READ_STATUS 0x05
#define CMD_WRITE_ENABLE 0x06
#define CMD_READ_CONFIG 0x35
#define CMD_FLAG_STATUS 0x70
/* Read commands */
#define CMD_READ_ARRAY_SLOW 0x03
#define CMD_READ_ARRAY_FAST 0x0b
#define CMD_READ_ID 0x9f
/* Bank addr access commands */
#ifdef CONFIG_SPI_FLASH_BAR
# define CMD_BANKADDR_BRWR 0x17
# define CMD_BANKADDR_BRRD 0x16
# define CMD_EXTNADDR_WREAR 0xC5
# define CMD_EXTNADDR_RDEAR 0xC8
#endif
/* Common status */
#define STATUS_WIP 0x01
#define STATUS_PEC 0x80
/* Flash timeout values */
#define SPI_FLASH_PROG_TIMEOUT (2 * CONFIG_SYS_HZ)
#define SPI_FLASH_PAGE_ERASE_TIMEOUT (5 * CONFIG_SYS_HZ)
#define SPI_FLASH_SECTOR_ERASE_TIMEOUT (10 * CONFIG_SYS_HZ)
/* SST specific */
#ifdef CONFIG_SPI_FLASH_SST
# define SST_WP 0x01 /* Supports AAI word program */
# define CMD_SST_BP 0x02 /* Byte Program */
# define CMD_SST_AAI_WP 0xAD /* Auto Address Incr Word Program */
int sst_write_wp(struct spi_flash *flash, u32 offset, size_t len,
const void *buf);
#endif
/* Send a single-byte command to the device and read the response */
int spi_flash_cmd(struct spi_slave *spi, u8 cmd, void *response, size_t len);
/*
* Send a multi-byte command to the device and read the response. Used
* for flash array reads, etc.
*/
int spi_flash_cmd_read(struct spi_slave *spi, const u8 *cmd,
size_t cmd_len, void *data, size_t data_len);
/*
* Send a multi-byte command to the device followed by (optional)
* data. Used for programming the flash array, etc.
*/
int spi_flash_cmd_write(struct spi_slave *spi, const u8 *cmd, size_t cmd_len,
const void *data, size_t data_len);
/* Flash erase(sectors) operation, support all possible erase commands */
int spi_flash_cmd_erase_ops(struct spi_flash *flash, u32 offset, size_t len);
/* Program the status register */
int spi_flash_cmd_write_status(struct spi_flash *flash, u8 sr);
/* Set quad enbale bit */
int spi_flash_set_qeb(struct spi_flash *flash);
/* Enable writing on the SPI flash */
static inline int spi_flash_cmd_write_enable(struct spi_flash *flash)
{
return spi_flash_cmd(flash->spi, CMD_WRITE_ENABLE, NULL, 0);
}
/* Disable writing on the SPI flash */
static inline int spi_flash_cmd_write_disable(struct spi_flash *flash)
{
return spi_flash_cmd(flash->spi, CMD_WRITE_DISABLE, NULL, 0);
}
/*
* Send the read status command to the device and wait for the wip
* (write-in-progress) bit to clear itself.
*/
int spi_flash_cmd_wait_ready(struct spi_flash *flash, unsigned long timeout);
/*
* Used for spi_flash write operation
* - SPI claim
* - spi_flash_cmd_write_enable
* - spi_flash_cmd_write
* - spi_flash_cmd_wait_ready
* - SPI release
*/
int spi_flash_write_common(struct spi_flash *flash, const u8 *cmd,
size_t cmd_len, const void *buf, size_t buf_len);
/*
* Flash write operation, support all possible write commands.
* Write the requested data out breaking it up into multiple write
* commands as needed per the write size.
*/
int spi_flash_cmd_write_ops(struct spi_flash *flash, u32 offset,
size_t len, const void *buf);
/*
* Same as spi_flash_cmd_read() except it also claims/releases the SPI
* bus. Used as common part of the ->read() operation.
*/
int spi_flash_read_common(struct spi_flash *flash, const u8 *cmd,
size_t cmd_len, void *data, size_t data_len);
/* Flash read operation, support all possible read commands */
int spi_flash_cmd_read_ops(struct spi_flash *flash, u32 offset,
size_t len, void *data);
#endif /* _SF_INTERNAL_H_ */