doc/README.sifive-fu540 - github/trini/u-boot - Gitiles

 FU540-C000 RISC-V SoC
 =====================
 The FU540-C000 is the world’s first 4+1 64-bit RISC‑V SoC from SiFive.

 The HiFive Unleashed development platform is based on FU540-C000 and capable
 of running Linux.

 Mainline support
 ================
 The support for following drivers are already enabled:
 1. SiFive UART Driver.
 2. SiFive PRCI Driver for clock.
 3. Cadence MACB ethernet driver for networking support.

 TODO:
 1. U-Boot expects the serial console device entry to be present under /chosen
    DT node. Example:
    chosen {
         stdout-path = "/soc/serial@10010000:115200";
    };

    Without a serial console U-Boot will panic.

 Building
 ========
 1. Add the RISC-V toolchain to your PATH.
 2. Setup ARCH & cross compilation enviornment variable.
    a. export ARCH=riscv
    b. export CROSS_COMPILE=<riscv64 toolchain prefix>
 3. make sifive_fu540_defconfig
 4. make

 Flashing
 ========
 The current U-Boot port is supported in S-mode only and loaded directly
 into DRAM.

 A prior stage (M-mode) firmware/bootloader (e.g OpenSBI) is required to
 boot the u-boot.bin in S-mode and provide M-mode runtime services.

 Currently, the u-boot.bin is used as a payload of the OpenSBI FW_PAYLOAD
 firmware. We need to compile OpenSBI with below command:
 make PLATFORM=sifive/fu540 FW_PAYLOAD_PATH=<path to u-boot.bin> FW_PAYLOAD_FDT_PATH=<path to hifive-unleashed-a00.dtb from Linux>
 (Note: Prefer hifive-unleashed-a00.dtb from Linux-5.3 or higher)
 (Note: Linux-5.2 is also fine but it does not have ethernet DT node)

 More detailed description of steps required to build FW_PAYLOAD firmware
 is beyond the scope of this document. Please refer OpenSBI documenation.
 (Note: OpenSBI git repo is at https://github.com/riscv/opensbi.git)

 Once the prior stage firmware/bootloader binary is generated, it should be
 copied to the first partition of the sdcard.

 sudo dd if=<prior_stage_firmware_binary> of=/dev/disk2s1 bs=1024

 Booting
 =======
 Once you plugin the sdcard and power up, you should see the U-Boot prompt.

 Sample boot log from HiFive Unleashed board
 ===========================================
 U-Boot 2019.07-rc4-00013-g1837f893b0 (Jun 20 2019 - 11:08:48 +0530)

 CPU:   rv64imafdc
 Model: SiFive HiFive Unleashed A00
 DRAM:  8 GiB
 In:    serial@10010000
 Out:   serial@10010000
 Err:   serial@10010000
 Net:   eth0: ethernet@10090000
 Hit any key to stop autoboot:  0
 => version
 U-Boot 2019.07-rc4-00013-g1837f893b0 (Jun 20 2019 - 11:08:48 +0530)

 riscv64-linux-gcc.br_real (Buildroot 2018.11-rc2-00003-ga0787e9) 8.2.0
 GNU ld (GNU Binutils) 2.31.1
 =>
 ===============================================================================

 Now you can configure your networking, tftp server and use tftp boot method to
 load uImage.

 ==========================================================================
 => setenv ipaddr 10.206.5.241
 => setenv netmask 255.255.252.0
 => setenv serverip 10.206.4.143
 => setenv gateway 10.206.4.1
 => tftpboot ${kernel_addr_r} /sifive/fu540/uImage
 ethernet@10090000: PHY present at 0
 ethernet@10090000: Starting autonegotiation...
 ethernet@10090000: Autonegotiation complete
 ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x7c00)
 Using ethernet@10090000 device
 TFTP from server 10.206.4.143; our IP address is 10.206.5.241
 Filename '/sifive/fu540/uImage'.
 Load address: 0x80600000
 Loading: #################################################################
          #################################################################
          #################################################################
          #################################################################
          #################################################################
          #################################################################
          #################################################################
          #################################################################
          #################################################################
          ########################################
          1.5 MiB/s
 done
 Bytes transferred = 9162364 (8bce7c hex)
 => tftpboot ${ramdisk_addr_r} /sifive/fu540/uRamdisk
 ethernet@10090000: PHY present at 0
 ethernet@10090000: Starting autonegotiation...
 ethernet@10090000: Autonegotiation complete
 ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x7c00)
 Using ethernet@10090000 device
 TFTP from server 10.206.4.143; our IP address is 10.206.5.241
 Filename '/sifive/fu540/uRamdisk'.
 Load address: 0x82500000
 Loading: #################################################################
          #################################################################
          ##################################
          448.2 KiB/s
 done
 Bytes transferred = 2398272 (249840 hex)
 => setenv bootargs "root=/dev/ram rw console=ttySIF0 earlycon=sbi"
 => bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdtcontroladdr}
 ## Booting kernel from Legacy Image at 80600000 ...
    Image Name:   Linux
    Image Type:   RISC-V Linux Kernel Image (uncompressed)
    Data Size:    9162300 Bytes = 8.7 MiB
    Load Address: 80200000
    Entry Point:  80200000
    Verifying Checksum ... OK
 ## Loading init Ramdisk from Legacy Image at 82500000 ...
    Image Name:   Linux RootFS
    Image Type:   RISC-V Linux RAMDisk Image (uncompressed)
    Data Size:    2398208 Bytes = 2.3 MiB
    Load Address: 00000000
    Entry Point:  00000000
    Verifying Checksum ... OK
 ## Flattened Device Tree blob at ff795730
    Booting using the fdt blob at 0xff795730
    Loading Kernel Image ... OK
    Using Device Tree in place at 00000000ff795730, end 00000000ff799dac

 Starting kernel ...

 [    0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
 [    0.000000] Linux version 5.2.0-rc1-00003-gb9543e66e700 (anup@anup-lab-machine) (gcc version 8.2.0 (Buildroot 2018.11-rc2-00003-ga0787e9)) #1 SMP Thu Jun 20 11:41:26 IST 2019
 [    0.000000] earlycon: sbi0 at I/O port 0x0 (options '')
 [    0.000000] printk: bootconsole [sbi0] enabled
 [    0.000000] Initial ramdisk at: 0x(____ptrval____) (2398208 bytes)
 [    0.000000] Zone ranges:
 [    0.000000]   DMA32    [mem 0x0000000080200000-0x00000000ffffffff]
 [    0.000000]   Normal   [mem 0x0000000100000000-0x000000027fffffff]
 [    0.000000] Movable zone start for each node
 [    0.000000] Early memory node ranges
 [    0.000000]   node   0: [mem 0x0000000080200000-0x000000027fffffff]
 [    0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff]
 [    0.000000] software IO TLB: mapped [mem 0xfb795000-0xff795000] (64MB)
 [    0.000000] CPU with hartid=0 is not available
 [    0.000000] CPU with hartid=0 is not available
 [    0.000000] elf_hwcap is 0x112d
 [    0.000000] percpu: Embedded 17 pages/cpu s29592 r8192 d31848 u69632
 [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 2067975
 [    0.000000] Kernel command line: root=/dev/ram rw console=ttySIF0 earlycon=sbi
 [    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
 [    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
 [    0.000000] Sorting __ex_table...
 [    0.000000] Memory: 8182056K/8386560K available (5753K kernel code, 357K rwdata, 1804K rodata, 204K init, 808K bss, 204504K reserved, 0K cma-reserved)
 [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
 [    0.000000] rcu: Hierarchical RCU implementation.
 [    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
 [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
 [    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
 [    0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
 [    0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts.
 [    0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [2]
 [    0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
 [    0.000007] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
 [    0.008553] Console: colour dummy device 80x25
 [    0.012990] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=4000)
 [    0.023103] pid_max: default: 32768 minimum: 301
 [    0.028269] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
 [    0.035068] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
 [    0.042770] *** VALIDATE proc ***
 [    0.045610] *** VALIDATE cgroup1 ***
 [    0.049157] *** VALIDATE cgroup2 ***
 [    0.053743] rcu: Hierarchical SRCU implementation.
 [    0.058297] smp: Bringing up secondary CPUs ...
 [    0.064134] smp: Brought up 1 node, 4 CPUs
 [    0.069114] devtmpfs: initialized
 [    0.073281] random: get_random_u32 called from bucket_table_alloc.isra.10+0x4e/0x160 with crng_init=0
 [    0.082157] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
 [    0.091634] futex hash table entries: 1024 (order: 4, 65536 bytes)
 [    0.098480] NET: Registered protocol family 16
 [    0.114101] vgaarb: loaded
 [    0.116397] SCSI subsystem initialized
 [    0.120358] usbcore: registered new interface driver usbfs
 [    0.125541] usbcore: registered new interface driver hub
 [    0.130936] usbcore: registered new device driver usb
 [    0.136618] clocksource: Switched to clocksource riscv_clocksource
 [    0.148108] NET: Registered protocol family 2
 [    0.152358] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes)
 [    0.159928] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
 [    0.169027] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
 [    0.178360] TCP: Hash tables configured (established 65536 bind 65536)
 [    0.184653] UDP hash table entries: 4096 (order: 5, 131072 bytes)
 [    0.190819] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
 [    0.197618] NET: Registered protocol family 1
 [    0.201892] RPC: Registered named UNIX socket transport module.
 [    0.207395] RPC: Registered udp transport module.
 [    0.212159] RPC: Registered tcp transport module.
 [    0.216940] RPC: Registered tcp NFSv4.1 backchannel transport module.
 [    0.223445] PCI: CLS 0 bytes, default 64
 [    0.227726] Unpacking initramfs...
 [    0.260556] Freeing initrd memory: 2336K
 [    0.264652] workingset: timestamp_bits=62 max_order=21 bucket_order=0
 [    0.278452] NFS: Registering the id_resolver key type
 [    0.282841] Key type id_resolver registered
 [    0.287067] Key type id_legacy registered
 [    0.291155] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
 [    0.298299] NET: Registered protocol family 38
 [    0.302470] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
 [    0.309906] io scheduler mq-deadline registered
 [    0.314501] io scheduler kyber registered
 [    0.354134] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
 [    0.360725] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 4, base_baud = 0) is a SiFive UART v0
 [    0.369191] printk: console [ttySIF0] enabled
 [    0.369191] printk: console [ttySIF0] enabled
 [    0.377938] printk: bootconsole [sbi0] disabled
 [    0.377938] printk: bootconsole [sbi0] disabled
 [    0.387298] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 1, base_baud = 0) is a SiFive UART v0
 [    0.396411] [drm] radeon kernel modesetting enabled.
 [    0.409818] loop: module loaded
 [    0.412606] libphy: Fixed MDIO Bus: probed
 [    0.416870] macb 10090000.ethernet: Registered clk switch 'sifive-gemgxl-mgmt'
 [    0.423570] macb: GEM doesn't support hardware ptp.
 [    0.428469] libphy: MACB_mii_bus: probed
 [    1.053009] Microsemi VSC8541 SyncE 10090000.ethernet-ffffffff:00: attached PHY driver [Microsemi VSC8541 SyncE] (mii_bus:phy_addr=10090000.ethernet-ffffffff:00, irq=POLL)
 [    1.067548] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 7 (70:b3:d5:92:f2:f3)
 [    1.077330] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
 [    1.083069] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
 [    1.089061] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 [    1.095485] ehci-pci: EHCI PCI platform driver
 [    1.099947] ehci-platform: EHCI generic platform driver
 [    1.105196] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 [    1.111286] ohci-pci: OHCI PCI platform driver
 [    1.115742] ohci-platform: OHCI generic platform driver
 [    1.121142] usbcore: registered new interface driver uas
 [    1.126269] usbcore: registered new interface driver usb-storage
 [    1.132331] mousedev: PS/2 mouse device common for all mice
 [    1.137978] usbcore: registered new interface driver usbhid
 [    1.143325] usbhid: USB HID core driver
 [    1.148022] NET: Registered protocol family 10
 [    1.152609] Segment Routing with IPv6
 [    1.155571] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
 [    1.161927] NET: Registered protocol family 17
 [    1.165907] Key type dns_resolver registered
 [    1.171694] Freeing unused kernel memory: 204K
 [    1.175375] This architecture does not have kernel memory protection.
 [    1.181792] Run /init as init process
            _  _
           | ||_|
           | | _ ____  _   _  _  _
           | || |  _ \| | | |\ \/ /
           | || | | | | |_| |/    \
           |_||_|_| |_|\____|\_/\_/

                Busybox Rootfs

 Please press Enter to activate this console.
 / #
	FU540-C000 RISC-V SoC
	=====================
	The FU540-C000 is the world’s first 4+1 64-bit RISC‑V SoC from SiFive.

	The HiFive Unleashed development platform is based on FU540-C000 and capable
	of running Linux.

	Mainline support
	================
	The support for following drivers are already enabled:
	1. SiFive UART Driver.
	2. SiFive PRCI Driver for clock.
	3. Cadence MACB ethernet driver for networking support.

	TODO:
	1. U-Boot expects the serial console device entry to be present under /chosen
	DT node. Example:
	chosen {
	stdout-path = "/soc/serial@10010000:115200";
	};

	Without a serial console U-Boot will panic.

	Building
	========
	1. Add the RISC-V toolchain to your PATH.
	2. Setup ARCH & cross compilation enviornment variable.
	a. export ARCH=riscv
	b. export CROSS_COMPILE=<riscv64 toolchain prefix>
	3. make sifive_fu540_defconfig
	4. make

	Flashing
	========
	The current U-Boot port is supported in S-mode only and loaded directly
	into DRAM.

	A prior stage (M-mode) firmware/bootloader (e.g OpenSBI) is required to
	boot the u-boot.bin in S-mode and provide M-mode runtime services.

	Currently, the u-boot.bin is used as a payload of the OpenSBI FW_PAYLOAD
	firmware. We need to compile OpenSBI with below command:
	make PLATFORM=sifive/fu540 FW_PAYLOAD_PATH=<path to u-boot.bin> FW_PAYLOAD_FDT_PATH=<path to hifive-unleashed-a00.dtb from Linux>
	(Note: Prefer hifive-unleashed-a00.dtb from Linux-5.3 or higher)
	(Note: Linux-5.2 is also fine but it does not have ethernet DT node)

	More detailed description of steps required to build FW_PAYLOAD firmware
	is beyond the scope of this document. Please refer OpenSBI documenation.
	(Note: OpenSBI git repo is at https://github.com/riscv/opensbi.git)

	Once the prior stage firmware/bootloader binary is generated, it should be
	copied to the first partition of the sdcard.

	sudo dd if=<prior_stage_firmware_binary> of=/dev/disk2s1 bs=1024

	Booting
	=======
	Once you plugin the sdcard and power up, you should see the U-Boot prompt.

	Sample boot log from HiFive Unleashed board
	===========================================
	U-Boot 2019.07-rc4-00013-g1837f893b0 (Jun 20 2019 - 11:08:48 +0530)

	CPU: rv64imafdc
	Model: SiFive HiFive Unleashed A00
	DRAM: 8 GiB
	In: serial@10010000
	Out: serial@10010000
	Err: serial@10010000
	Net: eth0: ethernet@10090000
	Hit any key to stop autoboot: 0
	=> version
	U-Boot 2019.07-rc4-00013-g1837f893b0 (Jun 20 2019 - 11:08:48 +0530)

	riscv64-linux-gcc.br_real (Buildroot 2018.11-rc2-00003-ga0787e9) 8.2.0
	GNU ld (GNU Binutils) 2.31.1
	=>
	===============================================================================

	Now you can configure your networking, tftp server and use tftp boot method to
	load uImage.

	==========================================================================
	=> setenv ipaddr 10.206.5.241
	=> setenv netmask 255.255.252.0
	=> setenv serverip 10.206.4.143
	=> setenv gateway 10.206.4.1
	=> tftpboot ${kernel_addr_r} /sifive/fu540/uImage
	ethernet@10090000: PHY present at 0
	ethernet@10090000: Starting autonegotiation...
	ethernet@10090000: Autonegotiation complete
	ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x7c00)
	Using ethernet@10090000 device
	TFTP from server 10.206.4.143; our IP address is 10.206.5.241
	Filename '/sifive/fu540/uImage'.
	Load address: 0x80600000
	Loading: #################################################################
	#################################################################
	#################################################################
	#################################################################
	#################################################################
	#################################################################
	#################################################################
	#################################################################
	#################################################################
	########################################
	1.5 MiB/s
	done
	Bytes transferred = 9162364 (8bce7c hex)
	=> tftpboot ${ramdisk_addr_r} /sifive/fu540/uRamdisk
	ethernet@10090000: PHY present at 0
	ethernet@10090000: Starting autonegotiation...
	ethernet@10090000: Autonegotiation complete
	ethernet@10090000: link up, 1000Mbps full-duplex (lpa: 0x7c00)
	Using ethernet@10090000 device
	TFTP from server 10.206.4.143; our IP address is 10.206.5.241
	Filename '/sifive/fu540/uRamdisk'.
	Load address: 0x82500000
	Loading: #################################################################
	#################################################################
	##################################
	448.2 KiB/s
	done
	Bytes transferred = 2398272 (249840 hex)
	=> setenv bootargs "root=/dev/ram rw console=ttySIF0 earlycon=sbi"
	=> bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdtcontroladdr}
	## Booting kernel from Legacy Image at 80600000 ...
	Image Name: Linux
	Image Type: RISC-V Linux Kernel Image (uncompressed)
	Data Size: 9162300 Bytes = 8.7 MiB
	Load Address: 80200000
	Entry Point: 80200000
	Verifying Checksum ... OK
	## Loading init Ramdisk from Legacy Image at 82500000 ...
	Image Name: Linux RootFS
	Image Type: RISC-V Linux RAMDisk Image (uncompressed)
	Data Size: 2398208 Bytes = 2.3 MiB
	Load Address: 00000000
	Entry Point: 00000000
	Verifying Checksum ... OK
	## Flattened Device Tree blob at ff795730
	Booting using the fdt blob at 0xff795730
	Loading Kernel Image ... OK
	Using Device Tree in place at 00000000ff795730, end 00000000ff799dac

	Starting kernel ...

	[ 0.000000] OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
	[ 0.000000] Linux version 5.2.0-rc1-00003-gb9543e66e700 (anup@anup-lab-machine) (gcc version 8.2.0 (Buildroot 2018.11-rc2-00003-ga0787e9)) #1 SMP Thu Jun 20 11:41:26 IST 2019
	[ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '')
	[ 0.000000] printk: bootconsole [sbi0] enabled
	[ 0.000000] Initial ramdisk at: 0x(____ptrval____) (2398208 bytes)
	[ 0.000000] Zone ranges:
	[ 0.000000] DMA32 [mem 0x0000000080200000-0x00000000ffffffff]
	[ 0.000000] Normal [mem 0x0000000100000000-0x000000027fffffff]
	[ 0.000000] Movable zone start for each node
	[ 0.000000] Early memory node ranges
	[ 0.000000] node 0: [mem 0x0000000080200000-0x000000027fffffff]
	[ 0.000000] Initmem setup node 0 [mem 0x0000000080200000-0x000000027fffffff]
	[ 0.000000] software IO TLB: mapped [mem 0xfb795000-0xff795000] (64MB)
	[ 0.000000] CPU with hartid=0 is not available
	[ 0.000000] CPU with hartid=0 is not available
	[ 0.000000] elf_hwcap is 0x112d
	[ 0.000000] percpu: Embedded 17 pages/cpu s29592 r8192 d31848 u69632
	[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975
	[ 0.000000] Kernel command line: root=/dev/ram rw console=ttySIF0 earlycon=sbi
	[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
	[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
	[ 0.000000] Sorting __ex_table...
	[ 0.000000] Memory: 8182056K/8386560K available (5753K kernel code, 357K rwdata, 1804K rodata, 204K init, 808K bss, 204504K reserved, 0K cma-reserved)
	[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
	[ 0.000000] rcu: Hierarchical RCU implementation.
	[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
	[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
	[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
	[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
	[ 0.000000] plic: mapped 53 interrupts with 4 handlers for 9 contexts.
	[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [2]
	[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 3526361616960 ns
	[ 0.000007] sched_clock: 64 bits at 1000kHz, resolution 1000ns, wraps every 2199023255500ns
	[ 0.008553] Console: colour dummy device 80x25
	[ 0.012990] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=4000)
	[ 0.023103] pid_max: default: 32768 minimum: 301
	[ 0.028269] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
	[ 0.035068] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
	[ 0.042770] * VALIDATE proc *
	[ 0.045610] * VALIDATE cgroup1 *
	[ 0.049157] * VALIDATE cgroup2 *
	[ 0.053743] rcu: Hierarchical SRCU implementation.
	[ 0.058297] smp: Bringing up secondary CPUs ...
	[ 0.064134] smp: Brought up 1 node, 4 CPUs
	[ 0.069114] devtmpfs: initialized
	[ 0.073281] random: get_random_u32 called from bucket_table_alloc.isra.10+0x4e/0x160 with crng_init=0
	[ 0.082157] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
	[ 0.091634] futex hash table entries: 1024 (order: 4, 65536 bytes)
	[ 0.098480] NET: Registered protocol family 16
	[ 0.114101] vgaarb: loaded
	[ 0.116397] SCSI subsystem initialized
	[ 0.120358] usbcore: registered new interface driver usbfs
	[ 0.125541] usbcore: registered new interface driver hub
	[ 0.130936] usbcore: registered new device driver usb
	[ 0.136618] clocksource: Switched to clocksource riscv_clocksource
	[ 0.148108] NET: Registered protocol family 2
	[ 0.152358] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes)
	[ 0.159928] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
	[ 0.169027] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
	[ 0.178360] TCP: Hash tables configured (established 65536 bind 65536)
	[ 0.184653] UDP hash table entries: 4096 (order: 5, 131072 bytes)
	[ 0.190819] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
	[ 0.197618] NET: Registered protocol family 1
	[ 0.201892] RPC: Registered named UNIX socket transport module.
	[ 0.207395] RPC: Registered udp transport module.
	[ 0.212159] RPC: Registered tcp transport module.
	[ 0.216940] RPC: Registered tcp NFSv4.1 backchannel transport module.
	[ 0.223445] PCI: CLS 0 bytes, default 64
	[ 0.227726] Unpacking initramfs...
	[ 0.260556] Freeing initrd memory: 2336K
	[ 0.264652] workingset: timestamp_bits=62 max_order=21 bucket_order=0
	[ 0.278452] NFS: Registering the id_resolver key type
	[ 0.282841] Key type id_resolver registered
	[ 0.287067] Key type id_legacy registered
	[ 0.291155] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
	[ 0.298299] NET: Registered protocol family 38
	[ 0.302470] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
	[ 0.309906] io scheduler mq-deadline registered
	[ 0.314501] io scheduler kyber registered
	[ 0.354134] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
	[ 0.360725] 10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 4, base_baud = 0) is a SiFive UART v0
	[ 0.369191] printk: console [ttySIF0] enabled
	[ 0.369191] printk: console [ttySIF0] enabled
	[ 0.377938] printk: bootconsole [sbi0] disabled
	[ 0.377938] printk: bootconsole [sbi0] disabled
	[ 0.387298] 10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 1, base_baud = 0) is a SiFive UART v0
	[ 0.396411] [drm] radeon kernel modesetting enabled.
	[ 0.409818] loop: module loaded
	[ 0.412606] libphy: Fixed MDIO Bus: probed
	[ 0.416870] macb 10090000.ethernet: Registered clk switch 'sifive-gemgxl-mgmt'
	[ 0.423570] macb: GEM doesn't support hardware ptp.
	[ 0.428469] libphy: MACB_mii_bus: probed
	[ 1.053009] Microsemi VSC8541 SyncE 10090000.ethernet-ffffffff:00: attached PHY driver [Microsemi VSC8541 SyncE] (mii_bus:phy_addr=10090000.ethernet-ffffffff:00, irq=POLL)
	[ 1.067548] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109 at 0x10090000 irq 7 (70:b3:d5:92:f2:f3)
	[ 1.077330] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
	[ 1.083069] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
	[ 1.089061] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
	[ 1.095485] ehci-pci: EHCI PCI platform driver
	[ 1.099947] ehci-platform: EHCI generic platform driver
	[ 1.105196] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
	[ 1.111286] ohci-pci: OHCI PCI platform driver
	[ 1.115742] ohci-platform: OHCI generic platform driver
	[ 1.121142] usbcore: registered new interface driver uas
	[ 1.126269] usbcore: registered new interface driver usb-storage
	[ 1.132331] mousedev: PS/2 mouse device common for all mice
	[ 1.137978] usbcore: registered new interface driver usbhid
	[ 1.143325] usbhid: USB HID core driver
	[ 1.148022] NET: Registered protocol family 10
	[ 1.152609] Segment Routing with IPv6
	[ 1.155571] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
	[ 1.161927] NET: Registered protocol family 17
	[ 1.165907] Key type dns_resolver registered
	[ 1.171694] Freeing unused kernel memory: 204K
	[ 1.175375] This architecture does not have kernel memory protection.
	[ 1.181792] Run /init as init process
	_ _
	\| \|\|_\|
	\| \| _ ____ _ _ _ _
	\| \|\| \| _ \\| \| \| \|\ \/ /
	\| \|\| \| \| \| \| \|_\| \|/ \
	\|_\|\|_\|_\| \|_\|\____\|\_/\_/

	Busybox Rootfs

	Please press Enter to activate this console.
	/ #