| /* |
| * Altera 10/100/1000 triple speed ethernet mac |
| * |
| * Copyright (C) 2008 Altera Corporation. |
| * Copyright (C) 2010 Thomas Chou <thomas@wytron.com.tw> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| #ifndef _ALTERA_TSE_H_ |
| #define _ALTERA_TSE_H_ |
| |
| #define __packed_1_ __attribute__ ((packed, aligned(1))) |
| |
| /* PHY Stuff */ |
| #define miim_end -2 |
| #define miim_read -1 |
| |
| #define PHY_AUTONEGOTIATE_TIMEOUT 5000 /* in ms */ |
| |
| #ifndef CONFIG_SYS_TBIPA_VALUE |
| #define CONFIG_SYS_TBIPA_VALUE 0x1f |
| #endif |
| #define MIIMCFG_INIT_VALUE 0x00000003 |
| #define MIIMCFG_RESET 0x80000000 |
| |
| #define MIIMIND_BUSY 0x00000001 |
| #define MIIMIND_NOTVALID 0x00000004 |
| |
| #define MIIM_CONTROL 0x00 |
| #define MIIM_CONTROL_RESET 0x00009140 |
| #define MIIM_CONTROL_INIT 0x00001140 |
| #define MIIM_CONTROL_RESTART 0x00001340 |
| #define MIIM_ANEN 0x00001000 |
| |
| #define MIIM_CR 0x00 |
| #define MIIM_CR_RST 0x00008000 |
| #define MIIM_CR_INIT 0x00001000 |
| |
| #define MIIM_STATUS 0x1 |
| #define MIIM_STATUS_AN_DONE 0x00000020 |
| #define MIIM_STATUS_LINK 0x0004 |
| |
| #define MIIM_PHYIR1 0x2 |
| #define MIIM_PHYIR2 0x3 |
| |
| #define MIIM_ANAR 0x4 |
| #define MIIM_ANAR_INIT 0x1e1 |
| |
| #define MIIM_TBI_ANLPBPA 0x5 |
| #define MIIM_TBI_ANLPBPA_HALF 0x00000040 |
| #define MIIM_TBI_ANLPBPA_FULL 0x00000020 |
| |
| #define MIIM_TBI_ANEX 0x6 |
| #define MIIM_TBI_ANEX_NP 0x00000004 |
| #define MIIM_TBI_ANEX_PRX 0x00000002 |
| |
| #define MIIM_GBIT_CONTROL 0x9 |
| #define MIIM_GBIT_CONTROL_INIT 0xe00 |
| |
| #define MIIM_EXT_PAGE_ACCESS 0x1f |
| |
| /* 88E1011 PHY Status Register */ |
| #define MIIM_88E1011_PHY_STATUS 0x11 |
| #define MIIM_88E1011_PHYSTAT_SPEED 0xc000 |
| #define MIIM_88E1011_PHYSTAT_GBIT 0x8000 |
| #define MIIM_88E1011_PHYSTAT_100 0x4000 |
| #define MIIM_88E1011_PHYSTAT_DUPLEX 0x2000 |
| #define MIIM_88E1011_PHYSTAT_SPDDONE 0x0800 |
| #define MIIM_88E1011_PHYSTAT_LINK 0x0400 |
| |
| #define MIIM_88E1011_PHY_SCR 0x10 |
| #define MIIM_88E1011_PHY_MDI_X_AUTO 0x0060 |
| |
| #define MIIM_88E1111_PHY_EXT_CR 0x14 |
| #define MIIM_88E1111_PHY_EXT_SR 0x1b |
| |
| /* 88E1111 PHY LED Control Register */ |
| #define MIIM_88E1111_PHY_LED_CONTROL 24 |
| #define MIIM_88E1111_PHY_LED_DIRECT 0x4100 |
| #define MIIM_88E1111_PHY_LED_COMBINE 0x411C |
| |
| #define MIIM_READ_COMMAND 0x00000001 |
| |
| /* struct phy_info: a structure which defines attributes for a PHY |
| * id will contain a number which represents the PHY. During |
| * startup, the driver will poll the PHY to find out what its |
| * UID--as defined by registers 2 and 3--is. The 32-bit result |
| * gotten from the PHY will be shifted right by "shift" bits to |
| * discard any bits which may change based on revision numbers |
| * unimportant to functionality |
| * |
| * The struct phy_cmd entries represent pointers to an arrays of |
| * commands which tell the driver what to do to the PHY. |
| */ |
| struct phy_info { |
| uint id; |
| char *name; |
| uint shift; |
| /* Called to configure the PHY, and modify the controller |
| * based on the results */ |
| struct phy_cmd *config; |
| |
| /* Called when starting up the controller */ |
| struct phy_cmd *startup; |
| |
| /* Called when bringing down the controller */ |
| struct phy_cmd *shutdown; |
| }; |
| |
| /* SGDMA Stuff */ |
| #define ALT_SGDMA_STATUS_ERROR_MSK (0x00000001) |
| #define ALT_SGDMA_STATUS_EOP_ENCOUNTERED_MSK (0x00000002) |
| #define ALT_SGDMA_STATUS_DESC_COMPLETED_MSK (0x00000004) |
| #define ALT_SGDMA_STATUS_CHAIN_COMPLETED_MSK (0x00000008) |
| #define ALT_SGDMA_STATUS_BUSY_MSK (0x00000010) |
| |
| #define ALT_SGDMA_CONTROL_IE_ERROR_MSK (0x00000001) |
| #define ALT_SGDMA_CONTROL_IE_EOP_ENCOUNTERED_MSK (0x00000002) |
| #define ALT_SGDMA_CONTROL_IE_DESC_COMPLETED_MSK (0x00000004) |
| #define ALT_SGDMA_CONTROL_IE_CHAIN_COMPLETED_MSK (0x00000008) |
| #define ALT_SGDMA_CONTROL_IE_GLOBAL_MSK (0x00000010) |
| #define ALT_SGDMA_CONTROL_RUN_MSK (0x00000020) |
| #define ALT_SGDMA_CONTROL_STOP_DMA_ER_MSK (0x00000040) |
| #define ALT_SGDMA_CONTROL_IE_MAX_DESC_PROCESSED_MSK (0x00000080) |
| #define ALT_SGDMA_CONTROL_MAX_DESC_PROCESSED_MSK (0x0000FF00) |
| #define ALT_SGDMA_CONTROL_SOFTWARERESET_MSK (0x00010000) |
| #define ALT_SGDMA_CONTROL_PARK_MSK (0x00020000) |
| #define ALT_SGDMA_CONTROL_CLEAR_INTERRUPT_MSK (0x80000000) |
| |
| #define ALTERA_TSE_SGDMA_INTR_MASK (ALT_SGDMA_CONTROL_IE_CHAIN_COMPLETED_MSK \ |
| | ALT_SGDMA_STATUS_DESC_COMPLETED_MSK \ |
| | ALT_SGDMA_CONTROL_IE_GLOBAL_MSK) |
| |
| /* |
| * Descriptor control bit masks & offsets |
| * |
| * Note: The control byte physically occupies bits [31:24] in memory. |
| * The following bit-offsets are expressed relative to the LSB of |
| * the control register bitfield. |
| */ |
| #define ALT_SGDMA_DESCRIPTOR_CONTROL_GENERATE_EOP_MSK (0x00000001) |
| #define ALT_SGDMA_DESCRIPTOR_CONTROL_READ_FIXED_ADDRESS_MSK (0x00000002) |
| #define ALT_SGDMA_DESCRIPTOR_CONTROL_WRITE_FIXED_ADDRESS_MSK (0x00000004) |
| #define ALT_SGDMA_DESCRIPTOR_CONTROL_ATLANTIC_CHANNEL_MSK (0x00000008) |
| #define ALT_SGDMA_DESCRIPTOR_CONTROL_OWNED_BY_HW_MSK (0x00000080) |
| |
| /* |
| * Descriptor status bit masks & offsets |
| * |
| * Note: The status byte physically occupies bits [23:16] in memory. |
| * The following bit-offsets are expressed relative to the LSB of |
| * the status register bitfield. |
| */ |
| #define ALT_SGDMA_DESCRIPTOR_STATUS_E_CRC_MSK (0x00000001) |
| #define ALT_SGDMA_DESCRIPTOR_STATUS_E_PARITY_MSK (0x00000002) |
| #define ALT_SGDMA_DESCRIPTOR_STATUS_E_OVERFLOW_MSK (0x00000004) |
| #define ALT_SGDMA_DESCRIPTOR_STATUS_E_SYNC_MSK (0x00000008) |
| #define ALT_SGDMA_DESCRIPTOR_STATUS_E_UEOP_MSK (0x00000010) |
| #define ALT_SGDMA_DESCRIPTOR_STATUS_E_MEOP_MSK (0x00000020) |
| #define ALT_SGDMA_DESCRIPTOR_STATUS_E_MSOP_MSK (0x00000040) |
| #define ALT_SGDMA_DESCRIPTOR_STATUS_TERMINATED_BY_EOP_MSK (0x00000080) |
| #define ALT_SGDMA_DESCRIPTOR_STATUS_ERROR_MSK (0x0000007F) |
| |
| /* |
| * The SGDMA controller buffer descriptor allocates |
| * 64 bits for each address. To support ANSI C, the |
| * struct implementing a descriptor places 32-bits |
| * of padding directly above each address; each pad must |
| * be cleared when initializing a descriptor. |
| */ |
| |
| /* |
| * Buffer Descriptor data structure |
| * |
| */ |
| struct alt_sgdma_descriptor { |
| unsigned int *source; /* the address of data to be read. */ |
| unsigned int source_pad; |
| |
| unsigned int *destination; /* the address to write data */ |
| unsigned int destination_pad; |
| |
| unsigned int *next; /* the next descriptor in the list. */ |
| unsigned int next_pad; |
| |
| unsigned short bytes_to_transfer; /* the number of bytes to transfer */ |
| unsigned char read_burst; |
| unsigned char write_burst; |
| |
| unsigned short actual_bytes_transferred;/* bytes transferred by DMA */ |
| unsigned char descriptor_status; |
| unsigned char descriptor_control; |
| |
| } __packed_1_; |
| |
| /* SG-DMA Control/Status Slave registers map */ |
| |
| struct alt_sgdma_registers { |
| unsigned int status; |
| unsigned int status_pad[3]; |
| unsigned int control; |
| unsigned int control_pad[3]; |
| unsigned int next_descriptor_pointer; |
| unsigned int descriptor_pad[3]; |
| }; |
| |
| /* TSE Stuff */ |
| #define ALTERA_TSE_CMD_TX_ENA_MSK (0x00000001) |
| #define ALTERA_TSE_CMD_RX_ENA_MSK (0x00000002) |
| #define ALTERA_TSE_CMD_XON_GEN_MSK (0x00000004) |
| #define ALTERA_TSE_CMD_ETH_SPEED_MSK (0x00000008) |
| #define ALTERA_TSE_CMD_PROMIS_EN_MSK (0x00000010) |
| #define ALTERA_TSE_CMD_PAD_EN_MSK (0x00000020) |
| #define ALTERA_TSE_CMD_CRC_FWD_MSK (0x00000040) |
| #define ALTERA_TSE_CMD_PAUSE_FWD_MSK (0x00000080) |
| #define ALTERA_TSE_CMD_PAUSE_IGNORE_MSK (0x00000100) |
| #define ALTERA_TSE_CMD_TX_ADDR_INS_MSK (0x00000200) |
| #define ALTERA_TSE_CMD_HD_ENA_MSK (0x00000400) |
| #define ALTERA_TSE_CMD_EXCESS_COL_MSK (0x00000800) |
| #define ALTERA_TSE_CMD_LATE_COL_MSK (0x00001000) |
| #define ALTERA_TSE_CMD_SW_RESET_MSK (0x00002000) |
| #define ALTERA_TSE_CMD_MHASH_SEL_MSK (0x00004000) |
| #define ALTERA_TSE_CMD_LOOPBACK_MSK (0x00008000) |
| /* Bits (18:16) = address select */ |
| #define ALTERA_TSE_CMD_TX_ADDR_SEL_MSK (0x00070000) |
| #define ALTERA_TSE_CMD_MAGIC_ENA_MSK (0x00080000) |
| #define ALTERA_TSE_CMD_SLEEP_MSK (0x00100000) |
| #define ALTERA_TSE_CMD_WAKEUP_MSK (0x00200000) |
| #define ALTERA_TSE_CMD_XOFF_GEN_MSK (0x00400000) |
| #define ALTERA_TSE_CMD_CNTL_FRM_ENA_MSK (0x00800000) |
| #define ALTERA_TSE_CMD_NO_LENGTH_CHECK_MSK (0x01000000) |
| #define ALTERA_TSE_CMD_ENA_10_MSK (0x02000000) |
| #define ALTERA_TSE_CMD_RX_ERR_DISC_MSK (0x04000000) |
| /* Bits (30..27) reserved */ |
| #define ALTERA_TSE_CMD_CNT_RESET_MSK (0x80000000) |
| |
| #define ALTERA_TSE_TX_CMD_STAT_TX_SHIFT16 (0x00040000) |
| #define ALTERA_TSE_TX_CMD_STAT_OMIT_CRC (0x00020000) |
| |
| #define ALTERA_TSE_RX_CMD_STAT_RX_SHIFT16 (0x02000000) |
| |
| #define ALT_TSE_SW_RESET_WATCHDOG_CNTR 10000 |
| #define ALT_TSE_SGDMA_BUSY_WATCHDOG_CNTR 90000000 |
| |
| /* Command_Config Register Bit Definitions */ |
| |
| typedef volatile union __alt_tse_command_config { |
| unsigned int image; |
| struct { |
| unsigned int |
| transmit_enable:1, /* bit 0 */ |
| receive_enable:1, /* bit 1 */ |
| pause_frame_xon_gen:1, /* bit 2 */ |
| ethernet_speed:1, /* bit 3 */ |
| promiscuous_enable:1, /* bit 4 */ |
| pad_enable:1, /* bit 5 */ |
| crc_forward:1, /* bit 6 */ |
| pause_frame_forward:1, /* bit 7 */ |
| pause_frame_ignore:1, /* bit 8 */ |
| set_mac_address_on_tx:1, /* bit 9 */ |
| halfduplex_enable:1, /* bit 10 */ |
| excessive_collision:1, /* bit 11 */ |
| late_collision:1, /* bit 12 */ |
| software_reset:1, /* bit 13 */ |
| multicast_hash_mode_sel:1, /* bit 14 */ |
| loopback_enable:1, /* bit 15 */ |
| src_mac_addr_sel_on_tx:3, /* bit 18:16 */ |
| magic_packet_detect:1, /* bit 19 */ |
| sleep_mode_enable:1, /* bit 20 */ |
| wake_up_request:1, /* bit 21 */ |
| pause_frame_xoff_gen:1, /* bit 22 */ |
| control_frame_enable:1, /* bit 23 */ |
| payload_len_chk_disable:1, /* bit 24 */ |
| enable_10mbps_intf:1, /* bit 25 */ |
| rx_error_discard_enable:1, /* bit 26 */ |
| reserved_bits:4, /* bit 30:27 */ |
| self_clear_counter_reset:1; /* bit 31 */ |
| } __packed_1_ bits; |
| } __packed_1_ alt_tse_command_config; |
| |
| /* Tx_Cmd_Stat Register Bit Definitions */ |
| |
| typedef volatile union __alt_tse_tx_cmd_stat { |
| unsigned int image; |
| struct { |
| unsigned int reserved_lsbs:17, /* bit 16:0 */ |
| omit_crc:1, /* bit 17 */ |
| tx_shift16:1, /* bit 18 */ |
| reserved_msbs:13; /* bit 31:19 */ |
| |
| } __packed_1_ bits; |
| } alt_tse_tx_cmd_stat; |
| |
| /* Rx_Cmd_Stat Register Bit Definitions */ |
| |
| typedef volatile union __alt_tse_rx_cmd_stat { |
| unsigned int image; |
| struct { |
| unsigned int reserved_lsbs:25, /* bit 24:0 */ |
| rx_shift16:1, /* bit 25 */ |
| reserved_msbs:6; /* bit 31:26 */ |
| |
| } __packed_1_ bits; |
| } alt_tse_rx_cmd_stat; |
| |
| struct alt_tse_mdio { |
| unsigned int control; /*PHY device operation control register */ |
| unsigned int status; /*PHY device operation status register */ |
| unsigned int phy_id1; /*Bits 31:16 of PHY identifier. */ |
| unsigned int phy_id2; /*Bits 15:0 of PHY identifier. */ |
| unsigned int auto_negotiation_advertisement; |
| unsigned int remote_partner_base_page_ability; |
| |
| unsigned int reg6; |
| unsigned int reg7; |
| unsigned int reg8; |
| unsigned int reg9; |
| unsigned int rega; |
| unsigned int regb; |
| unsigned int regc; |
| unsigned int regd; |
| unsigned int rege; |
| unsigned int regf; |
| unsigned int reg10; |
| unsigned int reg11; |
| unsigned int reg12; |
| unsigned int reg13; |
| unsigned int reg14; |
| unsigned int reg15; |
| unsigned int reg16; |
| unsigned int reg17; |
| unsigned int reg18; |
| unsigned int reg19; |
| unsigned int reg1a; |
| unsigned int reg1b; |
| unsigned int reg1c; |
| unsigned int reg1d; |
| unsigned int reg1e; |
| unsigned int reg1f; |
| }; |
| |
| /* MAC register Space */ |
| |
| struct alt_tse_mac { |
| unsigned int megacore_revision; |
| unsigned int scratch_pad; |
| alt_tse_command_config command_config; |
| unsigned int mac_addr_0; |
| unsigned int mac_addr_1; |
| unsigned int max_frame_length; |
| unsigned int pause_quanta; |
| unsigned int rx_sel_empty_threshold; |
| unsigned int rx_sel_full_threshold; |
| unsigned int tx_sel_empty_threshold; |
| unsigned int tx_sel_full_threshold; |
| unsigned int rx_almost_empty_threshold; |
| unsigned int rx_almost_full_threshold; |
| unsigned int tx_almost_empty_threshold; |
| unsigned int tx_almost_full_threshold; |
| unsigned int mdio_phy0_addr; |
| unsigned int mdio_phy1_addr; |
| |
| /* only if 100/1000 BaseX PCS, reserved otherwise */ |
| unsigned int reservedx44[5]; |
| |
| unsigned int reg_read_access_status; |
| unsigned int min_tx_ipg_length; |
| |
| /* IEEE 802.3 oEntity Managed Object Support */ |
| unsigned int aMACID_1; /*The MAC addresses */ |
| unsigned int aMACID_2; |
| unsigned int aFramesTransmittedOK; |
| unsigned int aFramesReceivedOK; |
| unsigned int aFramesCheckSequenceErrors; |
| unsigned int aAlignmentErrors; |
| unsigned int aOctetsTransmittedOK; |
| unsigned int aOctetsReceivedOK; |
| |
| /* IEEE 802.3 oPausedEntity Managed Object Support */ |
| unsigned int aTxPAUSEMACCtrlFrames; |
| unsigned int aRxPAUSEMACCtrlFrames; |
| |
| /* IETF MIB (MIB-II) Object Support */ |
| unsigned int ifInErrors; |
| unsigned int ifOutErrors; |
| unsigned int ifInUcastPkts; |
| unsigned int ifInMulticastPkts; |
| unsigned int ifInBroadcastPkts; |
| unsigned int ifOutDiscards; |
| unsigned int ifOutUcastPkts; |
| unsigned int ifOutMulticastPkts; |
| unsigned int ifOutBroadcastPkts; |
| |
| /* IETF RMON MIB Object Support */ |
| unsigned int etherStatsDropEvent; |
| unsigned int etherStatsOctets; |
| unsigned int etherStatsPkts; |
| unsigned int etherStatsUndersizePkts; |
| unsigned int etherStatsOversizePkts; |
| unsigned int etherStatsPkts64Octets; |
| unsigned int etherStatsPkts65to127Octets; |
| unsigned int etherStatsPkts128to255Octets; |
| unsigned int etherStatsPkts256to511Octets; |
| unsigned int etherStatsPkts512to1023Octets; |
| unsigned int etherStatsPkts1024to1518Octets; |
| |
| unsigned int etherStatsPkts1519toXOctets; |
| unsigned int etherStatsJabbers; |
| unsigned int etherStatsFragments; |
| |
| unsigned int reservedxE4; |
| |
| /*FIFO control register. */ |
| alt_tse_tx_cmd_stat tx_cmd_stat; |
| alt_tse_rx_cmd_stat rx_cmd_stat; |
| |
| unsigned int ipaccTxConf; |
| unsigned int ipaccRxConf; |
| unsigned int ipaccRxStat; |
| unsigned int ipaccRxStatSum; |
| |
| /*Multicast address resolution table */ |
| unsigned int hash_table[64]; |
| |
| /*Registers 0 to 31 within PHY device 0/1 */ |
| struct alt_tse_mdio mdio_phy0; |
| struct alt_tse_mdio mdio_phy1; |
| |
| /*4 Supplemental MAC Addresses */ |
| unsigned int supp_mac_addr_0_0; |
| unsigned int supp_mac_addr_0_1; |
| unsigned int supp_mac_addr_1_0; |
| unsigned int supp_mac_addr_1_1; |
| unsigned int supp_mac_addr_2_0; |
| unsigned int supp_mac_addr_2_1; |
| unsigned int supp_mac_addr_3_0; |
| unsigned int supp_mac_addr_3_1; |
| |
| unsigned int reservedx320[56]; |
| }; |
| |
| /* flags: TSE MII modes */ |
| /* GMII/MII = 0 */ |
| /* RGMII = 1 */ |
| /* RGMII_ID = 2 */ |
| /* RGMII_TXID = 3 */ |
| /* RGMII_RXID = 4 */ |
| /* SGMII = 5 */ |
| struct altera_tse_priv { |
| char devname[16]; |
| volatile struct alt_tse_mac *mac_dev; |
| volatile struct alt_sgdma_registers *sgdma_rx; |
| volatile struct alt_sgdma_registers *sgdma_tx; |
| unsigned int rx_sgdma_irq; |
| unsigned int tx_sgdma_irq; |
| unsigned int has_descriptor_mem; |
| unsigned int descriptor_mem_base; |
| unsigned int descriptor_mem_size; |
| volatile struct alt_sgdma_descriptor *rx_desc; |
| volatile struct alt_sgdma_descriptor *tx_desc; |
| volatile unsigned char *rx_buf; |
| struct phy_info *phyinfo; |
| unsigned int phyaddr; |
| unsigned int flags; |
| unsigned int link; |
| unsigned int duplexity; |
| unsigned int speed; |
| }; |
| |
| /* Phy stuff continued */ |
| /* |
| * struct phy_cmd: A command for reading or writing a PHY register |
| * |
| * mii_reg: The register to read or write |
| * |
| * mii_data: For writes, the value to put in the register. |
| * A value of -1 indicates this is a read. |
| * |
| * funct: A function pointer which is invoked for each command. |
| * For reads, this function will be passed the value read |
| * from the PHY, and process it. |
| * For writes, the result of this function will be written |
| * to the PHY register |
| */ |
| struct phy_cmd { |
| uint mii_reg; |
| uint mii_data; |
| uint(*funct) (uint mii_reg, struct altera_tse_priv *priv); |
| }; |
| #endif /* _ALTERA_TSE_H_ */ |