blob: 600f98cf0d40525fa758057d8a273664f3dec8a1 [file] [log] [blame]
/*
* (C) Copyright 2006-2007
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2006
* Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol@fr.ibm.com
* Alain Saurel, AMCC/IBM, alain.saurel@fr.ibm.com
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/************************************************************************
* sequoia.h - configuration for Sequoia & Rainier boards
***********************************************************************/
#ifndef __CONFIG_H
#define __CONFIG_H
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
/* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */
#ifndef CONFIG_RAINIER
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
#else
#define CONFIG_440GRX 1 /* Specific PPC440GRx */
#endif
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
/* Detect Sequoia PLL input clock automatically via CPLD bit */
#define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \
33333333 : 33000000)
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
#define CFG_BOOT_BASE_ADDR 0xf0000000
#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */
#define CFG_OCM_BASE 0xe0010000 /* ocm */
#define CFG_OCM_DATA_ADDR CFG_OCM_BASE
#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
/* Don't change either of these */
#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
#define CFG_USB2D0_BASE 0xe0000100
#define CFG_USB_DEVICE 0xe0000000
#define CFG_USB_HOST 0xe0000400
#define CFG_BCSR_BASE 0xc0000000
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer
*----------------------------------------------------------------------*/
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
#define CFG_INIT_RAM_END (4 << 10)
#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
#define CONFIG_BAUDRATE 115200
#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#else
#define CFG_ENV_IS_IN_NAND 1 /* use NAND for environment vars */
#define CFG_ENV_IS_EMBEDDED 1 /* use embedded environment */
#endif
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CFG_FLASH_CFI /* The flash is CFI compatible */
#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
#ifdef CFG_ENV_IS_IN_FLASH
#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#endif
/*
* IPL (Initial Program Loader, integrated inside CPU)
* Will load first 4k from NAND (SPL) into cache and execute it from there.
*
* SPL (Secondary Program Loader)
* Will load special U-Boot version (NUB) from NAND and execute it. This SPL
* has to fit into 4kByte. It sets up the CPU and configures the SDRAM
* controller and the NAND controller so that the special U-Boot image can be
* loaded from NAND to SDRAM.
*
* NUB (NAND U-Boot)
* This NAND U-Boot (NUB) is a special U-Boot version which can be started
* from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
*
* On 440EPx the SPL is copied to SDRAM before the NAND controller is
* set up. While still running from cache, I experienced problems accessing
* the NAND controller. sr - 2006-08-25
*/
#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */
#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
/*
* Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
*/
#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
/*
* Now the NAND chip has to be defined (no autodetection used!)
*/
#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
#define CFG_NAND_ECCSIZE 256
#define CFG_NAND_ECCBYTES 3
#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
#define CFG_NAND_OOBSIZE 16
#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
#ifdef CFG_ENV_IS_IN_NAND
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
* look at the file board/amcc/sequoia/u-boot-nand.lds for details.
*/
#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
#endif
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CFG_MBYTES_SDRAM (256) /* 256MB */
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
#endif
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
#define CFG_I2C_EEPROM_ADDR_LEN 1
#define CFG_EEPROM_PAGE_WRITE_ENABLE
#define CFG_EEPROM_PAGE_WRITE_BITS 3
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_AD7414 1 /* use AD7414 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
#define CFG_DTT_MAX_TEMP 70
#define CFG_DTT_LOW_TEMP -30
#define CFG_DTT_HYSTERESIS 3
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
/* Setup some board specific values for the default environment variables */
#ifndef CONFIG_RAINIER
#define CONFIG_HOSTNAME sequoia
#define CFG_BOOTFILE "bootfile=/tftpboot/sequoia/uImage\0"
#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0"
#else
#define CONFIG_HOSTNAME rainier
#define CFG_BOOTFILE "bootfile=/tftpboot/rainier/uImage\0"
#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0"
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
CFG_BOOTFILE \
CFG_ROOTPATH \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_nfs=run nfsargs addip addtty;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
"kernel_addr=FC000000\0" \
"ramdisk_addr=FC180000\0" \
"load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \
"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
"cp.b 200000 FFFA0000 60000\0" \
"upd=run load;run update\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_HAS_ETH0
#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 1
/* USB */
#ifdef CONFIG_440EPX
#define CONFIG_USB_OHCI
#define CONFIG_USB_STORAGE
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
#endif /* CONFIG_440EPX */
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DTT
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NET
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#ifdef CONFIG_440EPX
#define CONFIG_CMD_USB
#endif
#ifndef CONFIG_RAINIER
#define CFG_POST_FPU_ON CFG_POST_FPU
#else
#define CFG_POST_FPU_ON 0
#endif
/* POST support */
#define CONFIG_POST (CFG_POST_MEMORY | \
CFG_POST_CPU | \
CFG_POST_UART | \
CFG_POST_I2C | \
CFG_POST_CACHE | \
CFG_POST_FPU_ON | \
CFG_POST_ETHER | \
CFG_POST_SPR)
#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
#define CONFIG_LOGBUFFER
#define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */
#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
#define CONFIG_SUPPORT_VFAT
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*----------------------------------------------------------------------*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* General PCI */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
/* Board-specific PCI */
#define CFG_PCI_TARGET_INIT
#define CFG_PCI_MASTER_INIT
#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
/*
* On Sequoia CS0 and CS3 are switched when configuring for NAND booting
*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CFG_NAND_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
#define CFG_EBC_PB0AP 0x03017200
#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
/* Memory Bank 3 (NAND-FLASH) initialization */
#define CFG_EBC_PB3AP 0x018003c0
#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000)
#else
#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
/* Memory Bank 3 (NOR-FLASH) initialization */
#define CFG_EBC_PB3AP 0x03017200
#define CFG_EBC_PB3CR (CFG_FLASH_BASE | 0xda000)
/* Memory Bank 0 (NAND-FLASH) initialization */
#define CFG_EBC_PB0AP 0x018003c0
#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000)
#endif
/* Memory Bank 2 (CPLD) initialization */
#define CFG_EBC_PB2AP 0x24814580
#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x38000)
#define CFG_BCSR5_PCI66EN 0x80
/*-----------------------------------------------------------------------
* NAND FLASH
*----------------------------------------------------------------------*/
#define CFG_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
/*-----------------------------------------------------------------------
* Cache Configuration
*----------------------------------------------------------------------*/
#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
#define CFG_CACHELINE_SIZE 32 /* ... */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#endif /* __CONFIG_H */