include/configs/sbc8349.h - github/trini/u-boot - Gitiles

 /*
  * WindRiver SBC8349 U-Boot configuration file.
  * Copyright (c) 2006, 2007 Wind River Systems, Inc.
  *
  * Paul Gortmaker <paul.gortmaker@windriver.com>
  * Based on the MPC8349EMDS config.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /*
  * sbc8349 board configuration file.
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_DISPLAY_BOARDINFO

 /*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1	/* E300 Family */
 #define CONFIG_MPC834x		1	/* MPC834x family */
 #define CONFIG_MPC8349		1	/* MPC8349 specific */
 #define CONFIG_SBC8349		1	/* WRS SBC8349 board specific */

 #define	CONFIG_SYS_TEXT_BASE	0xFF800000

 /* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
 #undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */

 /*
  * The default if PCI isn't enabled, or if no PCI clk setting is given
  * is 66MHz; this is what the board defaults to when the PCI slot is
  * physically empty.  The board will automatically (i.e w/o jumpers)
  * clock down to 33MHz if you insert a 33MHz PCI card.
  */
 #ifdef CONFIG_PCI_33M
 #define CONFIG_83XX_CLKIN	33000000	/* in Hz */
 #else	/* 66M */
 #define CONFIG_83XX_CLKIN	66000000	/* in Hz */
 #endif

 #ifndef CONFIG_SYS_CLK_FREQ
 #ifdef CONFIG_PCI_33M
 #define CONFIG_SYS_CLK_FREQ	33000000
 #define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_8X1
 #else	/* 66M */
 #define CONFIG_SYS_CLK_FREQ	66000000
 #define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_4X1
 #endif
 #endif

 #undef CONFIG_BOARD_EARLY_INIT_F		/* call board_pre_init */

 #define CONFIG_SYS_IMMR		0xE0000000

 #undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
 #define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x00100000

 /*
  * DDR Setup
  */
 #undef CONFIG_DDR_ECC			/* only for ECC DDR module */
 #undef CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
 #define CONFIG_SPD_EEPROM		/* use SPD EEPROM for DDR setup*/
 #define CONFIG_SYS_83XX_DDR_USES_CS0	/* WRS; Fsl board uses CS2/CS3 */

 /*
  * 32-bit data path mode.
  *
  * Please note that using this mode for devices with the real density of 64-bit
  * effectively reduces the amount of available memory due to the effect of
  * wrapping around while translating address to row/columns, for example in the
  * 256MB module the upper 128MB get aliased with contents of the lower
  * 128MB); normally this define should be used for devices with real 32-bit
  * data path.
  */
 #undef CONFIG_DDR_32BIT

 #define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
 				DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
 #define CONFIG_DDR_2T_TIMING

 #if defined(CONFIG_SPD_EEPROM)
 /*
  * Determine DDR configuration from I2C interface.
  */
 #define SPD_EEPROM_ADDRESS	0x52		/* DDR DIMM */

 #else
 /*
  * Manually set up DDR parameters
  * NB: manual DDR setup untested on sbc834x
  */
 #define CONFIG_SYS_DDR_SIZE		256		/* MB */
 #define CONFIG_SYS_DDR_CS2_CONFIG	(CSCONFIG_EN \
 					| CSCONFIG_ROW_BIT_13 \
 					| CSCONFIG_COL_BIT_10)
 #define CONFIG_SYS_DDR_TIMING_1	0x36332321
 #define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
 #define CONFIG_SYS_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
 #define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */

 #if defined(CONFIG_DDR_32BIT)
 /* set burst length to 8 for 32-bit data path */
 				/* DLL,normal,seq,4/2.5, 8 burst len */
 #define CONFIG_SYS_DDR_MODE	0x00000023
 #else
 /* the default burst length is 4 - for 64-bit data path */
 				/* DLL,normal,seq,4/2.5, 4 burst len */
 #define CONFIG_SYS_DDR_MODE	0x00000022
 #endif
 #endif

 /*
  * SDRAM on the Local Bus
  */
 #define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* Localbus SDRAM */
 #define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */

 /*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
 #define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
 #define CONFIG_SYS_FLASH_BASE		0xFF800000	/* start of FLASH   */
 #define CONFIG_SYS_FLASH_SIZE		8		/* flash size in MB */
 /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */

 #define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE \
 					| BR_PS_16	/* 16 bit port */ \
 					| BR_MS_GPCM	/* MSEL = GPCM */ \
 					| BR_V)		/* valid */

 #define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 					| OR_GPCM_XAM \
 					| OR_GPCM_CSNT \
 					| OR_GPCM_ACS_DIV2 \
 					| OR_GPCM_XACS \
 					| OR_GPCM_SCY_15 \
 					| OR_GPCM_TRLX_SET \
 					| OR_GPCM_EHTR_SET \
 					| OR_GPCM_EAD)
 					/* 0xFF806FF7 */

 					/* window base at flash base */
 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	64	/* sectors per device */

 #undef CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #else
 #undef  CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_SYS_INIT_RAM_LOCK	1
 					/* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000
 					/* Size of used area in RAM*/
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000

 #define CONFIG_SYS_GBL_DATA_OFFSET	\
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN	(256 * 1024)	/* Reserve 256 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(256 * 1024)	/* Reserved for malloc */

 /*
  * Local Bus LCRR and LBCR regs
  *    LCRR:  DLL bypass, Clock divider is 4
  * External Local Bus rate is
  *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
  */
 #define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
 #define CONFIG_SYS_LCRR_CLKDIV	LCRR_CLKDIV_4
 #define CONFIG_SYS_LBC_LBCR	0x00000000

 #undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */

 #ifdef CONFIG_SYS_LB_SDRAM
 /* Local bus BR2, OR2 definition for SDRAM if soldered on the board*/
 /*
  * Base Register 2 and Option Register 2 configure SDRAM.
  * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
  *
  * For BR2, need:
  *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
  *    port-size = 32-bits = BR2[19:20] = 11
  *    no parity checking = BR2[21:22] = 00
  *    SDRAM for MSEL = BR2[24:26] = 011
  *    Valid = BR[31] = 1
  *
  * 0    4    8    12   16   20   24   28
  * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
  */

 #define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_LBC_SDRAM_BASE \
 					| BR_PS_32 \
 					| BR_MS_SDRAM \
 					| BR_V)
 					/* 0xF0001861 */
 #define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_LBC_SDRAM_BASE
 #define CONFIG_SYS_LBLAWAR2_PRELIM	(LBLAWAR_EN | LBLAWAR_64MB)

 /*
  * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
  *
  * For OR2, need:
  *    64MB mask for AM, OR2[0:7] = 1111 1100
  *                 XAM, OR2[17:18] = 11
  *    9 columns OR2[19-21] = 010
  *    13 rows   OR2[23-25] = 100
  *    EAD set for extra time OR[31] = 1
  *
  * 0    4    8    12   16   20   24   28
  * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
  */

 #define CONFIG_SYS_OR2_PRELIM	(MEG_TO_AM(CONFIG_SYS_LBC_SDRAM_SIZE) \
 			| OR_SDRAM_XAM \
 			| ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
 			| ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
 			| OR_SDRAM_EAD)
 			/* 0xFC006901 */

 				/* LB sdram refresh timer, about 6us */
 #define CONFIG_SYS_LBC_LSRT	0x32000000
 				/* LB refresh timer prescal, 266MHz/32 */
 #define CONFIG_SYS_LBC_MRTPR	0x20000000

 #define CONFIG_SYS_LBC_LSDMR_COMMON	(LSDMR_RFEN \
 					| LSDMR_BSMA1516 \
 					| LSDMR_RFCR8 \
 					| LSDMR_PRETOACT6 \
 					| LSDMR_ACTTORW3 \
 					| LSDMR_BL8 \
 					| LSDMR_WRC3 \
 					| LSDMR_CL3)

 /*
  * SDRAM Controller configuration sequence.
  */
 #define CONFIG_SYS_LBC_LSDMR_1	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
 #define CONFIG_SYS_LBC_LSDMR_2	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 #define CONFIG_SYS_LBC_LSDMR_3	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 #define CONFIG_SYS_LBC_LSDMR_4	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 #define CONFIG_SYS_LBC_LSDMR_5	(CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 #endif

 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX     1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

 #define CONFIG_SYS_BAUDRATE_TABLE  \
 		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)

 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_AUTO_COMPLETE		/* add autocompletion support   */

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69}, {1, 0x69} }
 /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */

 /* TSEC */
 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 #define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 #define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
 #define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
 #define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
 #define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
 #define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI1_IO_BASE		0x00000000
 #define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
 #define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */

 #define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
 #define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
 #define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
 #define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
 #define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI2_IO_BASE		0x00000000
 #define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
 #define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */

 #if defined(CONFIG_PCI)

 #define PCI_64BIT
 #define PCI_ONE_PCI1
 #if defined(PCI_64BIT)
 #undef PCI_ALL_PCI1
 #undef PCI_TWO_PCI1
 #undef PCI_ONE_PCI1
 #endif

 #define CONFIG_PCI_PNP		/* do pci plug-and-play */

 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP

 #if !defined(CONFIG_PCI_PNP)
 	#define PCI_ENET0_IOADDR	0xFIXME
 	#define PCI_ENET0_MEMADDR	0xFIXME
 	#define PCI_IDSEL_NUMBER	0xFIXME
 #endif

 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */

 #endif	/* CONFIG_PCI */

 /*
  * TSEC configuration
  */
 #define CONFIG_TSEC_ENET		/* TSEC ethernet support */

 #if defined(CONFIG_TSEC_ENET)

 #define CONFIG_TSEC1	1
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
 #define CONFIG_PHY_BCM5421S	1
 #define TSEC1_PHY_ADDR		0x19
 #define TSEC2_PHY_ADDR		0x1a
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 #define TSEC1_FLAGS		TSEC_GIGABIT
 #define TSEC2_FLAGS		TSEC_GIGABIT

 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"

 #endif	/* CONFIG_TSEC_ENET */

 /*
  * Environment
  */
 #ifndef CONFIG_SYS_RAMBOOT
 	#define CONFIG_ENV_IS_IN_FLASH	1
 	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x40000)
 	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
 	#define CONFIG_ENV_SIZE		0x2000

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

 #else
 	#define CONFIG_SYS_NO_FLASH	1	/* Flash is not usable now */
 	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
 	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 	#define CONFIG_ENV_SIZE		0x2000
 #endif

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME

 /*
  * Command line configuration.
  */
 #define CONFIG_CMD_MII

 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
 #endif

 #undef CONFIG_WATCHDOG			/* watchdog disabled */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */

 #if defined(CONFIG_CMD_KGDB)
 	#define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
 #else
 	#define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
 #endif

 				/* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
 				/* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 256 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 				/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20)

 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */

 #if 1 /*528/264*/
 #define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
 	HRCWL_VCO_1X2 |\
 	HRCWL_CORE_TO_CSB_2X1)
 #elif 0 /*396/132*/
 #define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
 	HRCWL_VCO_1X4 |\
 	HRCWL_CORE_TO_CSB_3X1)
 #elif 0 /*264/132*/
 #define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
 	HRCWL_VCO_1X4 |\
 	HRCWL_CORE_TO_CSB_2X1)
 #elif 0 /*132/132*/
 #define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
 	HRCWL_VCO_1X4 |\
 	HRCWL_CORE_TO_CSB_1X1)
 #elif 0 /*264/264 */
 #define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
 	HRCWL_VCO_1X4 |\
 	HRCWL_CORE_TO_CSB_1X1)
 #endif

 #if defined(PCI_64BIT)
 #define CONFIG_SYS_HRCW_HIGH (\
 	HRCWH_PCI_HOST |\
 	HRCWH_64_BIT_PCI |\
 	HRCWH_PCI1_ARBITER_ENABLE |\
 	HRCWH_PCI2_ARBITER_DISABLE |\
 	HRCWH_CORE_ENABLE |\
 	HRCWH_FROM_0X00000100 |\
 	HRCWH_BOOTSEQ_DISABLE |\
 	HRCWH_SW_WATCHDOG_DISABLE |\
 	HRCWH_ROM_LOC_LOCAL_16BIT |\
 	HRCWH_TSEC1M_IN_GMII |\
 	HRCWH_TSEC2M_IN_GMII)
 #else
 #define CONFIG_SYS_HRCW_HIGH (\
 	HRCWH_PCI_HOST |\
 	HRCWH_32_BIT_PCI |\
 	HRCWH_PCI1_ARBITER_ENABLE |\
 	HRCWH_PCI2_ARBITER_ENABLE |\
 	HRCWH_CORE_ENABLE |\
 	HRCWH_FROM_0X00000100 |\
 	HRCWH_BOOTSEQ_DISABLE |\
 	HRCWH_SW_WATCHDOG_DISABLE |\
 	HRCWH_ROM_LOC_LOCAL_16BIT |\
 	HRCWH_TSEC1M_IN_GMII |\
 	HRCWH_TSEC2M_IN_GMII)
 #endif

 /* System IO Config */
 #define CONFIG_SYS_SICRH 0
 #define CONFIG_SYS_SICRL SICRL_LDP_A

 #define CONFIG_SYS_HID0_INIT	0x000000000
 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK \
 				| HID0_ENABLE_INSTRUCTION_CACHE)

 /* #define CONFIG_SYS_HID0_FINAL	(\
 	HID0_ENABLE_INSTRUCTION_CACHE |\
 	HID0_ENABLE_M_BIT |\
 	HID0_ENABLE_ADDRESS_BROADCAST) */

 #define CONFIG_SYS_HID2 HID2_HBE

 #define CONFIG_HIGH_BATS	1	/* High BATs supported */

 /* DDR @ 0x00000000 */
 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
 				| BATL_PP_RW \
 				| BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)

 /* PCI @ 0x80000000 */
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE \
 				| BATL_PP_RW \
 				| BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE \
 				| BATL_PP_RW \
 				| BATL_CACHEINHIBIT \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)
 #else
 #define CONFIG_SYS_IBAT1L	(0)
 #define CONFIG_SYS_IBAT1U	(0)
 #define CONFIG_SYS_IBAT2L	(0)
 #define CONFIG_SYS_IBAT2U	(0)
 #endif

 #ifdef CONFIG_MPC83XX_PCI2
 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI2_MEM_BASE \
 				| BATL_PP_RW \
 				| BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI2_MEM_BASE \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)
 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI2_MMIO_BASE \
 				| BATL_PP_RW \
 				| BATL_CACHEINHIBIT \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI2_MMIO_BASE \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)
 #else
 #define CONFIG_SYS_IBAT3L	(0)
 #define CONFIG_SYS_IBAT3U	(0)
 #define CONFIG_SYS_IBAT4L	(0)
 #define CONFIG_SYS_IBAT4U	(0)
 #endif

 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
 #define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR \
 				| BATL_PP_RW \
 				| BATL_CACHEINHIBIT \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)

 /* LBC SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
 #define CONFIG_SYS_IBAT6L	(CONFIG_SYS_LBC_SDRAM_BASE \
 				| BATL_PP_RW \
 				| BATL_MEMCOHERENCE \
 				| BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT6U	(CONFIG_SYS_LBC_SDRAM_BASE \
 				| BATU_BL_256M \
 				| BATU_VS \
 				| BATU_VP)

 #define CONFIG_SYS_IBAT7L	(0)
 #define CONFIG_SYS_IBAT7U	(0)

 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
 #define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
 #define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
 #define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
 #define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
 #define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
 #define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
 #define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
 #define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
 #define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
 #define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_ENV_OVERWRITE

 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #endif

 #define CONFIG_HOSTNAME		SBC8349
 #define CONFIG_ROOTPATH		"/tftpboot/rootfs"
 #define CONFIG_BOOTFILE		"uImage"

 				/* default location for tftp and bootm */
 #define CONFIG_LOADADDR		800000

 #define CONFIG_BOOTDELAY	6	/* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */

 #define CONFIG_BAUDRATE	 115200

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"hostname=sbc8349\0"						\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 	"flash_nfs=run nfsargs addip addtty;"				\
 		"bootm ${kernel_addr}\0"				\
 	"flash_self=run ramargs addip addtty;"				\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
 		"bootm\0"						\
 	"load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0"		\
 	"update=protect off ff800000 ff83ffff; "			\
 		"era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
 	"upd=run load update\0"						\
 	"fdtaddr=780000\0"						\
 	"fdtfile=sbc8349.dtb\0"						\
 	""

 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv bootargs root=/dev/nfs rw "				\
 		"nfsroot=$serverip:$rootpath "				\
 		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
 							"$netdev:off "	\
 		"console=$consoledev,$baudrate $othbootargs;"		\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND						\
 	"setenv bootargs root=/dev/ram rw "				\
 		"console=$consoledev,$baudrate $othbootargs;"		\
 	"tftp $ramdiskaddr $ramdiskfile;"				\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr $ramdiskaddr $fdtaddr"

 #define CONFIG_BOOTCOMMAND	"run flash_self"

 #endif	/* __CONFIG_H */
	/*
	* WindRiver SBC8349 U-Boot configuration file.
	* Copyright (c) 2006, 2007 Wind River Systems, Inc.
	*
	* Paul Gortmaker <paul.gortmaker@windriver.com>
	* Based on the MPC8349EMDS config.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/*
	* sbc8349 board configuration file.
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_DISPLAY_BOARDINFO

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_E300 1 /* E300 Family */
	#define CONFIG_MPC834x 1 /* MPC834x family */
	#define CONFIG_MPC8349 1 /* MPC8349 specific */
	#define CONFIG_SBC8349 1 /* WRS SBC8349 board specific */

	#define CONFIG_SYS_TEXT_BASE 0xFF800000

	/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
	#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */

	/*
	* The default if PCI isn't enabled, or if no PCI clk setting is given
	* is 66MHz; this is what the board defaults to when the PCI slot is
	* physically empty. The board will automatically (i.e w/o jumpers)
	* clock down to 33MHz if you insert a 33MHz PCI card.
	*/
	#ifdef CONFIG_PCI_33M
	#define CONFIG_83XX_CLKIN 33000000 /* in Hz */
	#else /* 66M */
	#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
	#endif

	#ifndef CONFIG_SYS_CLK_FREQ
	#ifdef CONFIG_PCI_33M
	#define CONFIG_SYS_CLK_FREQ 33000000
	#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
	#else /* 66M */
	#define CONFIG_SYS_CLK_FREQ 66000000
	#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
	#endif
	#endif

	#undef CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */

	#define CONFIG_SYS_IMMR 0xE0000000

	#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
	#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
	#define CONFIG_SYS_MEMTEST_END 0x00100000

	/*
	* DDR Setup
	*/
	#undef CONFIG_DDR_ECC /* only for ECC DDR module */
	#undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
	#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
	#define CONFIG_SYS_83XX_DDR_USES_CS0 /* WRS; Fsl board uses CS2/CS3 */

	/*
	* 32-bit data path mode.
	*
	* Please note that using this mode for devices with the real density of 64-bit
	* effectively reduces the amount of available memory due to the effect of
	* wrapping around while translating address to row/columns, for example in the
	* 256MB module the upper 128MB get aliased with contents of the lower
	* 128MB); normally this define should be used for devices with real 32-bit
	* data path.
	*/
	#undef CONFIG_DDR_32BIT

	#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \| \
	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
	#define CONFIG_DDR_2T_TIMING

	#if defined(CONFIG_SPD_EEPROM)
	/*
	* Determine DDR configuration from I2C interface.
	*/
	#define SPD_EEPROM_ADDRESS 0x52 /* DDR DIMM */

	#else
	/*
	* Manually set up DDR parameters
	* NB: manual DDR setup untested on sbc834x
	*/
	#define CONFIG_SYS_DDR_SIZE 256 /* MB */
	#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \
	\| CSCONFIG_ROW_BIT_13 \
	\| CSCONFIG_COL_BIT_10)
	#define CONFIG_SYS_DDR_TIMING_1 0x36332321
	#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
	#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
	#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */

	#if defined(CONFIG_DDR_32BIT)
	/* set burst length to 8 for 32-bit data path */
	/* DLL,normal,seq,4/2.5, 8 burst len */
	#define CONFIG_SYS_DDR_MODE 0x00000023
	#else
	/* the default burst length is 4 - for 64-bit data path */
	/* DLL,normal,seq,4/2.5, 4 burst len */
	#define CONFIG_SYS_DDR_MODE 0x00000022
	#endif
	#endif

	/*
	* SDRAM on the Local Bus
	*/
	#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */
	#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */

	/*
	* FLASH on the Local Bus
	*/
	#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
	#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
	#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* start of FLASH */
	#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */
	/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */

	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
	\| BR_PS_16 /* 16 bit port */ \
	\| BR_MS_GPCM /* MSEL = GPCM */ \
	\| BR_V) /* valid */

	#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
	\| OR_GPCM_XAM \
	\| OR_GPCM_CSNT \
	\| OR_GPCM_ACS_DIV2 \
	\| OR_GPCM_XACS \
	\| OR_GPCM_SCY_15 \
	\| OR_GPCM_TRLX_SET \
	\| OR_GPCM_EHTR_SET \
	\| OR_GPCM_EAD)
	/* 0xFF806FF7 */

	/* window base at flash base */
	#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN \| LBLAWAR_8MB)

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */

	#undef CONFIG_SYS_FLASH_CHECKSUM
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */

	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT
	#else
	#undef CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_SYS_INIT_RAM_LOCK 1
	/* Initial RAM address */
	#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000
	/* Size of used area in RAM*/
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000

	#define CONFIG_SYS_GBL_DATA_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */

	/*
	* Local Bus LCRR and LBCR regs
	* LCRR: DLL bypass, Clock divider is 4
	* External Local Bus rate is
	* CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
	*/
	#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
	#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
	#define CONFIG_SYS_LBC_LBCR 0x00000000

	#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */

	#ifdef CONFIG_SYS_LB_SDRAM
	/* Local bus BR2, OR2 definition for SDRAM if soldered on the board*/
	/*
	* Base Register 2 and Option Register 2 configure SDRAM.
	* The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
	*
	* For BR2, need:
	* Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
	* port-size = 32-bits = BR2[19:20] = 11
	* no parity checking = BR2[21:22] = 00
	* SDRAM for MSEL = BR2[24:26] = 011
	* Valid = BR[31] = 1
	*
	* 0 4 8 12 16 20 24 28
	* 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
	*/

	#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LBC_SDRAM_BASE \
	\| BR_PS_32 \
	\| BR_MS_SDRAM \
	\| BR_V)
	/* 0xF0001861 */
	#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE
	#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN \| LBLAWAR_64MB)

	/*
	* The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
	*
	* For OR2, need:
	* 64MB mask for AM, OR2[0:7] = 1111 1100
	* XAM, OR2[17:18] = 11
	* 9 columns OR2[19-21] = 010
	* 13 rows OR2[23-25] = 100
	* EAD set for extra time OR[31] = 1
	*
	* 0 4 8 12 16 20 24 28
	* 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
	*/

	#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_LBC_SDRAM_SIZE) \
	\| OR_SDRAM_XAM \
	\| ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \
	\| ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \
	\| OR_SDRAM_EAD)
	/* 0xFC006901 */

	/* LB sdram refresh timer, about 6us */
	#define CONFIG_SYS_LBC_LSRT 0x32000000
	/* LB refresh timer prescal, 266MHz/32 */
	#define CONFIG_SYS_LBC_MRTPR 0x20000000

	#define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \
	\| LSDMR_BSMA1516 \
	\| LSDMR_RFCR8 \
	\| LSDMR_PRETOACT6 \
	\| LSDMR_ACTTORW3 \
	\| LSDMR_BL8 \
	\| LSDMR_WRC3 \
	\| LSDMR_CL3)

	/*
	* SDRAM Controller configuration sequence.
	*/
	#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_PCHALL)
	#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_ARFRSH)
	#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_ARFRSH)
	#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_MRW)
	#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON \| LSDMR_OP_NORMAL)
	#endif

	/*
	* Serial Port
	*/
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)

	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
	#define CONFIG_AUTO_COMPLETE /* add autocompletion support */

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69}, {1, 0x69} }
	/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */

	/* TSEC */
	#define CONFIG_SYS_TSEC1_OFFSET 0x24000
	#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
	#define CONFIG_SYS_TSEC2_OFFSET 0x25000
	#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
	#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
	#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
	#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
	#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
	#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
	#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */

	#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
	#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
	#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
	#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
	#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
	#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
	#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */

	#if defined(CONFIG_PCI)

	#define PCI_64BIT
	#define PCI_ONE_PCI1
	#if defined(PCI_64BIT)
	#undef PCI_ALL_PCI1
	#undef PCI_TWO_PCI1
	#undef PCI_ONE_PCI1
	#endif

	#define CONFIG_PCI_PNP /* do pci plug-and-play */

	#undef CONFIG_EEPRO100
	#undef CONFIG_TULIP

	#if !defined(CONFIG_PCI_PNP)
	#define PCI_ENET0_IOADDR 0xFIXME
	#define PCI_ENET0_MEMADDR 0xFIXME
	#define PCI_IDSEL_NUMBER 0xFIXME
	#endif

	#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */

	#endif /* CONFIG_PCI */

	/*
	* TSEC configuration
	*/
	#define CONFIG_TSEC_ENET /* TSEC ethernet support */

	#if defined(CONFIG_TSEC_ENET)

	#define CONFIG_TSEC1 1
	#define CONFIG_TSEC1_NAME "TSEC0"
	#define CONFIG_TSEC2 1
	#define CONFIG_TSEC2_NAME "TSEC1"
	#define CONFIG_PHY_BCM5421S 1
	#define TSEC1_PHY_ADDR 0x19
	#define TSEC2_PHY_ADDR 0x1a
	#define TSEC1_PHYIDX 0
	#define TSEC2_PHYIDX 0
	#define TSEC1_FLAGS TSEC_GIGABIT
	#define TSEC2_FLAGS TSEC_GIGABIT

	/* Options are: TSEC[0-1] */
	#define CONFIG_ETHPRIME "TSEC0"

	#endif /* CONFIG_TSEC_ENET */

	/*
	* Environment
	*/
	#ifndef CONFIG_SYS_RAMBOOT
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
	#define CONFIG_ENV_SIZE 0x2000

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)

	#else
	#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
	#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE 0x2000
	#endif

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME

	/*
	* Command line configuration.
	*/
	#define CONFIG_CMD_MII

	#if defined(CONFIG_PCI)
	#define CONFIG_CMD_PCI
	#endif

	#undef CONFIG_WATCHDOG /* watchdog disabled */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif

	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 256 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	/* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTMAPSZ (256 << 20)

	#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */

	#if 1 /528/264/
	#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	HRCWL_DDR_TO_SCB_CLK_1X1 \|\
	HRCWL_CSB_TO_CLKIN \|\
	HRCWL_VCO_1X2 \|\
	HRCWL_CORE_TO_CSB_2X1)
	#elif 0 /396/132/
	#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	HRCWL_DDR_TO_SCB_CLK_1X1 \|\
	HRCWL_CSB_TO_CLKIN \|\
	HRCWL_VCO_1X4 \|\
	HRCWL_CORE_TO_CSB_3X1)
	#elif 0 /264/132/
	#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	HRCWL_DDR_TO_SCB_CLK_1X1 \|\
	HRCWL_CSB_TO_CLKIN \|\
	HRCWL_VCO_1X4 \|\
	HRCWL_CORE_TO_CSB_2X1)
	#elif 0 /132/132/
	#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	HRCWL_DDR_TO_SCB_CLK_1X1 \|\
	HRCWL_CSB_TO_CLKIN \|\
	HRCWL_VCO_1X4 \|\
	HRCWL_CORE_TO_CSB_1X1)
	#elif 0 /264/264 /
	#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \|\
	HRCWL_DDR_TO_SCB_CLK_1X1 \|\
	HRCWL_CSB_TO_CLKIN \|\
	HRCWL_VCO_1X4 \|\
	HRCWL_CORE_TO_CSB_1X1)
	#endif

	#if defined(PCI_64BIT)
	#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_HOST \|\
	HRCWH_64_BIT_PCI \|\
	HRCWH_PCI1_ARBITER_ENABLE \|\
	HRCWH_PCI2_ARBITER_DISABLE \|\
	HRCWH_CORE_ENABLE \|\
	HRCWH_FROM_0X00000100 \|\
	HRCWH_BOOTSEQ_DISABLE \|\
	HRCWH_SW_WATCHDOG_DISABLE \|\
	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	HRCWH_TSEC1M_IN_GMII \|\
	HRCWH_TSEC2M_IN_GMII)
	#else
	#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_PCI_HOST \|\
	HRCWH_32_BIT_PCI \|\
	HRCWH_PCI1_ARBITER_ENABLE \|\
	HRCWH_PCI2_ARBITER_ENABLE \|\
	HRCWH_CORE_ENABLE \|\
	HRCWH_FROM_0X00000100 \|\
	HRCWH_BOOTSEQ_DISABLE \|\
	HRCWH_SW_WATCHDOG_DISABLE \|\
	HRCWH_ROM_LOC_LOCAL_16BIT \|\
	HRCWH_TSEC1M_IN_GMII \|\
	HRCWH_TSEC2M_IN_GMII)
	#endif

	/* System IO Config */
	#define CONFIG_SYS_SICRH 0
	#define CONFIG_SYS_SICRL SICRL_LDP_A

	#define CONFIG_SYS_HID0_INIT 0x000000000
	#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \
	\| HID0_ENABLE_INSTRUCTION_CACHE)

	/* #define CONFIG_SYS_HID0_FINAL (\
	HID0_ENABLE_INSTRUCTION_CACHE \|\
	HID0_ENABLE_M_BIT \|\
	HID0_ENABLE_ADDRESS_BROADCAST) */

	#define CONFIG_SYS_HID2 HID2_HBE

	#define CONFIG_HIGH_BATS 1 /* High BATs supported */

	/* DDR @ 0x00000000 */
	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \
	\| BATL_PP_RW \
	\| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)

	/* PCI @ 0x80000000 */
	#ifdef CONFIG_PCI
	#define CONFIG_PCI_INDIRECT_BRIDGE
	#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \
	\| BATL_PP_RW \
	\| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \
	\| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)
	#else
	#define CONFIG_SYS_IBAT1L (0)
	#define CONFIG_SYS_IBAT1U (0)
	#define CONFIG_SYS_IBAT2L (0)
	#define CONFIG_SYS_IBAT2U (0)
	#endif

	#ifdef CONFIG_MPC83XX_PCI2
	#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \
	\| BATL_PP_RW \
	\| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)
	#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \
	\| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)
	#else
	#define CONFIG_SYS_IBAT3L (0)
	#define CONFIG_SYS_IBAT3U (0)
	#define CONFIG_SYS_IBAT4L (0)
	#define CONFIG_SYS_IBAT4U (0)
	#endif

	/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */
	#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \
	\| BATL_PP_RW \
	\| BATL_CACHEINHIBIT \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)

	/* LBC SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
	#define CONFIG_SYS_IBAT6L (CONFIG_SYS_LBC_SDRAM_BASE \
	\| BATL_PP_RW \
	\| BATL_MEMCOHERENCE \
	\| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT6U (CONFIG_SYS_LBC_SDRAM_BASE \
	\| BATU_BL_256M \
	\| BATU_VS \
	\| BATU_VP)

	#define CONFIG_SYS_IBAT7L (0)
	#define CONFIG_SYS_IBAT7U (0)

	#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
	#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
	#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
	#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
	#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
	#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
	#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
	#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
	#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
	#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
	#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
	#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_ENV_OVERWRITE

	#if defined(CONFIG_TSEC_ENET)
	#define CONFIG_HAS_ETH0
	#define CONFIG_HAS_ETH1
	#endif

	#define CONFIG_HOSTNAME SBC8349
	#define CONFIG_ROOTPATH "/tftpboot/rootfs"
	#define CONFIG_BOOTFILE "uImage"

	/* default location for tftp and bootm */
	#define CONFIG_LOADADDR 800000

	#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
	#undef CONFIG_BOOTARGS /* the boot command will set bootargs */

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"hostname=sbc8349\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
	"flash_nfs=run nfsargs addip addtty;" \
	"bootm ${kernel_addr}\0" \
	"flash_self=run ramargs addip addtty;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
	"bootm\0" \
	"load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0" \
	"update=protect off ff800000 ff83ffff; " \
	"era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
	"upd=run load update\0" \
	"fdtaddr=780000\0" \
	"fdtfile=sbc8349.dtb\0" \
	""

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
	"$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_BOOTCOMMAND "run flash_self"

	#endif /* __CONFIG_H */