| /* |
| * Configuration settings for the Sentec Cobra Board. |
| * |
| * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * configuration for ASTRO "Urmel" board. |
| * Originating from Cobra5272 configuration, messed up by |
| * Wolfgang Wegner <w.wegner@astro-kom.de> |
| * Please do not bother the original author with bug reports |
| * concerning this file. |
| */ |
| |
| #ifndef _CONFIG_ASTRO_MCF5373L_H |
| #define _CONFIG_ASTRO_MCF5373L_H |
| |
| #include <linux/stringify.h> |
| |
| /* |
| * set the card type to actually compile for; either of |
| * the possibilities listed below has to be used! |
| */ |
| #define CONFIG_ASTRO_V532 1 |
| |
| #if CONFIG_ASTRO_V532 |
| #define ASTRO_ID 0xF8 |
| #elif CONFIG_ASTRO_V512 |
| #define ASTRO_ID 0xFA |
| #elif CONFIG_ASTRO_TWIN7S2 |
| #define ASTRO_ID 0xF9 |
| #elif CONFIG_ASTRO_V912 |
| #define ASTRO_ID 0xFC |
| #elif CONFIG_ASTRO_COFDMDUOS2 |
| #define ASTRO_ID 0xFB |
| #else |
| #error No card type defined! |
| #endif |
| |
| #define CONFIG_ASTRO5373L /* define board type */ |
| |
| /* Command line configuration */ |
| /* |
| * CONFIG_RAM defines if u-boot is loaded via BDM (or started from |
| * a different bootloader that has already performed RAM setup) or |
| * started directly from flash, which is the regular case for production |
| * boards. |
| */ |
| #ifdef CONFIG_RAM |
| #define CONFIG_MONITOR_IS_IN_RAM |
| #define CONFIG_SYS_TEXT_BASE 0x40020000 |
| #define ENABLE_JFFS 0 |
| #else |
| #define CONFIG_SYS_TEXT_BASE 0x00000000 |
| #define ENABLE_JFFS 1 |
| #endif |
| |
| /* Define which commands should be available at u-boot command prompt */ |
| |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_DATE |
| #if ENABLE_JFFS |
| #define CONFIG_CMD_JFFS2 |
| #endif |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_FPGA_LOADMK |
| #define CONFIG_CMDLINE_EDITING |
| |
| #define CONFIG_MCFRTC |
| #undef RTC_DEBUG |
| |
| /* Timer */ |
| #define CONFIG_MCFTMR |
| #undef CONFIG_MCFPIT |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 80000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 |
| #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR |
| |
| /* |
| * Defines processor clock - important for correct timings concerning serial |
| * interface etc. |
| */ |
| |
| #define CONFIG_SYS_CLK 80000000 |
| #define CONFIG_SYS_CPU_CLK (CONFIG_SYS_CLK * 3) |
| #define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */ |
| |
| #define CONFIG_SYS_CORE_SRAM_SIZE 0x8000 |
| #define CONFIG_SYS_CORE_SRAM 0x80000000 |
| |
| #define CONFIG_SYS_UNIFY_CACHE |
| |
| /* |
| * Define baudrate for UART1 (console output, tftp, ...) |
| * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud |
| * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected |
| * in u-boot command interface |
| */ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_MCFUART |
| #define CONFIG_SYS_UART_PORT (2) |
| #define CONFIG_SYS_UART2_ALT3_GPIO |
| |
| /* |
| * Watchdog configuration; Watchdog is disabled for running from RAM |
| * and set to highest possible value else. Beware there is no check |
| * in the watchdog code to validate the timeout value set here! |
| */ |
| |
| #ifndef CONFIG_MONITOR_IS_IN_RAM |
| #define CONFIG_WATCHDOG |
| #define CONFIG_WATCHDOG_TIMEOUT 3355 /* timeout in milliseconds */ |
| #endif |
| |
| /* |
| * Configuration for environment |
| * Environment is located in the last sector of the flash |
| */ |
| |
| #ifndef CONFIG_MONITOR_IS_IN_RAM |
| #define CONFIG_ENV_OFFSET 0x1FF8000 |
| #define CONFIG_ENV_SECT_SIZE 0x8000 |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #else |
| /* |
| * environment in RAM - This is used to use a single PC-based application |
| * to load an image, load U-Boot, load an environment and then start U-Boot |
| * to execute the commands from the environment. Feedback is done via setting |
| * and reading memory locations. |
| */ |
| #define CONFIG_ENV_ADDR 0x40060000 |
| #define CONFIG_ENV_SECT_SIZE 0x8000 |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #endif |
| |
| /* here we put our FPGA configuration... */ |
| #define CONFIG_MISC_INIT_R 1 |
| |
| /* Define user parameters that have to be customized most likely */ |
| |
| /* AUTOBOOT settings - booting images automatically by u-boot after power on */ |
| |
| /* |
| * used for autoboot, delay in seconds u-boot will wait before starting |
| * defined (auto-)boot command, setting to -1 disables delay, setting to |
| * 0 will too prevent access to u-boot command interface: u-boot then has |
| * to be reflashed |
| * beware - watchdog is not serviced during autoboot delay time! |
| */ |
| #ifdef CONFIG_MONITOR_IS_IN_RAM |
| #define CONFIG_BOOTDELAY 1 |
| #else |
| #define CONFIG_BOOTDELAY 1 |
| #endif |
| |
| /* |
| * The following settings will be contained in the environment block ; if you |
| * want to use a neutral environment all those settings can be manually set in |
| * u-boot: 'set' command |
| */ |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "loaderversion=11\0" \ |
| "card_id="__stringify(ASTRO_ID)"\0" \ |
| "alterafile=0\0" \ |
| "xilinxfile=0\0" \ |
| "xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\ |
| "fpga load 0 0x41000000 $filesize\0" \ |
| "alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\ |
| "fpga load 1 0x41000000 $filesize\0" \ |
| "env_default=1\0" \ |
| "env_check=if test $env_default -eq 1;"\ |
| " then setenv env_default 0;saveenv;fi\0" |
| |
| /* |
| * "update" is a non-standard command that has to be supplied |
| * by external update.c; This is not included in mainline because |
| * it needs non-blocking CFI routines. |
| */ |
| #ifdef CONFIG_MONITOR_IS_IN_RAM |
| #define CONFIG_BOOTCOMMAND "" /* no autoboot in this case */ |
| #else |
| #if CONFIG_ASTRO_V532 |
| #define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\ |
| "run xilinxload&&run alteraload&&bootm 0x80000;"\ |
| "update;reset" |
| #else |
| #define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\ |
| "run xilinxload&&bootm 0x80000;update;reset" |
| #endif |
| #endif |
| |
| /* default bootargs that are considered during boot */ |
| #define CONFIG_BOOTARGS " console=ttyS2,115200 rootfstype=romfs"\ |
| " loaderversion=$loaderversion" |
| |
| /* default RAM address for user programs */ |
| #define CONFIG_SYS_LOAD_ADDR 0x20000 |
| |
| #define CONFIG_SYS_LONGHELP |
| |
| #if (CONFIG_COMMANDS & CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 |
| #else |
| #define CONFIG_SYS_CBSIZE 256 |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) |
| #define CONFIG_SYS_MAXARGS 16 |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE |
| |
| #define CONFIG_FPGA_COUNT 1 |
| #define CONFIG_FPGA |
| #define CONFIG_FPGA_XILINX |
| #define CONFIG_FPGA_SPARTAN3 |
| #define CONFIG_FPGA_ALTERA |
| #define CONFIG_FPGA_CYCLON2 |
| #define CONFIG_SYS_FPGA_PROG_FEEDBACK |
| #define CONFIG_SYS_FPGA_WAIT 1000 |
| |
| /* End of user parameters to be customized */ |
| |
| /* Defines memory range for test */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x40020000 |
| #define CONFIG_SYS_MEMTEST_END 0x41ffffff |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| |
| /* Base register address */ |
| |
| #define CONFIG_SYS_MBAR 0xFC000000 /* Register Base Addrs */ |
| |
| /* System Conf. Reg. & System Protection Reg. */ |
| |
| #define CONFIG_SYS_SCR 0x0003; |
| #define CONFIG_SYS_SPR 0xffff; |
| |
| /* |
| * Definitions for initial stack pointer and data area (in internal SRAM) |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x8000 |
| #define CONFIG_SYS_INIT_RAM_CTRL 0x221 |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * for MCF5373, the allowable range is 0x40000000 to 0x7FF00000 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x40000000 |
| |
| /* |
| * Chipselect bank definitions |
| * |
| * CS0 - Flash 32MB (first 16MB) |
| * CS1 - Flash 32MB (second half) |
| * CS2 - FPGA |
| * CS3 - FPGA |
| * CS4 - unused |
| * CS5 - unused |
| */ |
| #define CONFIG_SYS_CS0_BASE 0 |
| #define CONFIG_SYS_CS0_MASK 0x00ff0001 |
| #define CONFIG_SYS_CS0_CTRL 0x00001fc0 |
| |
| #define CONFIG_SYS_CS1_BASE 0x01000000 |
| #define CONFIG_SYS_CS1_MASK 0x00ff0001 |
| #define CONFIG_SYS_CS1_CTRL 0x00001fc0 |
| |
| #define CONFIG_SYS_CS2_BASE 0x20000000 |
| #define CONFIG_SYS_CS2_MASK 0x00ff0001 |
| #define CONFIG_SYS_CS2_CTRL 0x0000fec0 |
| |
| #define CONFIG_SYS_CS3_BASE 0x21000000 |
| #define CONFIG_SYS_CS3_MASK 0x00ff0001 |
| #define CONFIG_SYS_CS3_CTRL 0x0000fec0 |
| |
| #define CONFIG_SYS_FLASH_BASE 0x00000000 |
| |
| #ifdef CONFIG_MONITOR_IS_IN_RAM |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #else |
| /* This is mainly used during relocation in start.S */ |
| #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) |
| #endif |
| /* Reserve 256 kB for Monitor */ |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) |
| |
| #define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) |
| /* Reserve 128 kB for malloc() */ |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization ?? |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ |
| (CONFIG_SYS_SDRAM_SIZE << 20)) |
| |
| /* FLASH organization */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| #define CONFIG_SYS_MAX_FLASH_SECT 259 |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 |
| |
| #define CONFIG_SYS_FLASH_CFI 1 |
| #define CONFIG_FLASH_CFI_DRIVER 1 |
| #define CONFIG_SYS_FLASH_SIZE 0x2000000 |
| #define CONFIG_SYS_FLASH_PROTECTION 1 |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 |
| #define CONFIG_SYS_FLASH_CFI_NONBLOCK 1 |
| |
| #define LDS_BOARD_TEXT \ |
| . = DEFINED(env_offset) ? env_offset : .; \ |
| common/env_embedded.o (.text*) |
| |
| #if ENABLE_JFFS |
| /* JFFS Partition offset set */ |
| #define CONFIG_SYS_JFFS2_FIRST_BANK 0 |
| #define CONFIG_SYS_JFFS2_NUM_BANKS 1 |
| /* 512k reserved for u-boot */ |
| #define CONFIG_SYS_JFFS2_FIRST_SECTOR 0x40 |
| #endif |
| |
| /* Cache Configuration */ |
| #define CONFIG_SYS_CACHELINE_SIZE 16 |
| |
| #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ |
| CONFIG_SYS_INIT_RAM_SIZE - 8) |
| #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ |
| CONFIG_SYS_INIT_RAM_SIZE - 4) |
| #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA) |
| #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ |
| CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ |
| CF_ACR_EN | CF_ACR_SM_ALL) |
| #define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \ |
| CF_CACR_DCM_P) |
| |
| #endif /* _CONFIG_ASTRO_MCF5373L_H */ |