| /* |
| * (C) Copyright 2004 |
| * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_405EP 1 /* This is a PPC405 CPU */ |
| #define CONFIG_G2000 1 /* ...on a PLU405 board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFFC0000 |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ |
| #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ |
| |
| #if 0 /* test-only */ |
| #define CONFIG_BAUDRATE 115200 |
| #else |
| #define CONFIG_BAUDRATE 9600 |
| #endif |
| |
| #define CONFIG_PREBOOT |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off\0" \ |
| "addmisc=setenv bootargs ${bootargs} " \ |
| "console=ttyS0,${baudrate} " \ |
| "panic=1\0" \ |
| "flash_nfs=run nfsargs addip addmisc;" \ |
| "bootm ${kernel_addr}\0" \ |
| "flash_self=run ramargs addip addmisc;" \ |
| "bootm ${kernel_addr} ${ramdisk_addr}\0" \ |
| "net_nfs=tftp 200000 ${bootfile};" \ |
| "run nfsargs addip addmisc;bootm\0" \ |
| "rootpath=/opt/eldk/ppc_4xx\0" \ |
| "bootfile=/tftpboot/g2000/pImage\0" \ |
| "kernel_addr=ff800000\0" \ |
| "ramdisk_addr=ff900000\0" \ |
| "pciconfighost=yes\0" \ |
| "" |
| #define CONFIG_BOOTCOMMAND "run net_nfs" |
| |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| |
| #define CONFIG_PPC4xx_EMAC |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_PHY_ADDR 0 /* PHY address */ |
| #define CONFIG_PHY1_ADDR 1 /* PHY address */ |
| |
| #if 0 /* test-only */ |
| #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ |
| #endif |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_BSP |
| #define CONFIG_CMD_EEPROM |
| |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| #if 0 /* test-only */ |
| #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| |
| #undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ |
| |
| #define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ |
| |
| #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_serial_clock() |
| |
| #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ |
| #define CONFIG_SYS_BASE_BAUD 691200 |
| |
| /* The following table includes the supported baudrates */ |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ |
| 57600, 115200, 230400, 460800, 921600 } |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ |
| |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ |
| #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ |
| |
| #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ |
| |
| #define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ |
| |
| /*----------------------------------------------------------------------------*/ |
| /* adding Ethernet setting: FTS OUI 00:11:0B */ |
| /*----------------------------------------------------------------------------*/ |
| #define CONFIG_ETHADDR 00:11:0B:00:00:01 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_ETH1ADDR 00:11:0B:00:00:02 |
| #define CONFIG_IPADDR 10.48.8.178 |
| #define CONFIG_IP1ADDR 10.48.8.188 |
| #define CONFIG_NETMASK 255.255.255.128 |
| #define CONFIG_SERVERIP 10.48.8.138 |
| |
| /*----------------------------------------------------------------------- |
| * RTC stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_RTC_DS1337 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| |
| #if 0 /* test-only */ |
| /*----------------------------------------------------------------------- |
| * NAND-FLASH stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ |
| |
| #define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */ |
| #define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ |
| #define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ |
| #define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ |
| |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ |
| #define PCI_HOST_FORCE 1 /* configure as pci host */ |
| #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ |
| |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #define CONFIG_PCI_HOST PCI_HOST_HOST /* select pci host function */ |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| /* resource configuration */ |
| |
| #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ |
| |
| #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/ |
| |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ |
| #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */ |
| #define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ |
| #define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ |
| #define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ |
| #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ |
| #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ |
| #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ |
| #define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #if 0 /* APC405 */ |
| #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ |
| #undef CONFIG_SYS_FLASH_PROTECTION /* don't use hardware protection */ |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* test-only...*/ |
| #define CONFIG_SYS_FLASH_INCREMENT 0x01000000 /* test-only */ |
| #else /* G2000 */ |
| #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #undef CONFIG_SYS_FLASH_PROTECTION /* don't use hardware protection */ |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| #define CONFIG_SYS_FLASH_BASE 0xFF800000 /* test-only...*/ |
| #define CONFIG_SYS_FLASH_INCREMENT 0x01000000 /* test-only */ |
| #endif |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| |
| #define CONFIG_SYS_JFFS2_FIRST_BANK 0 /* use for JFFS2 */ |
| #define CONFIG_SYS_JFFS2_NUM_BANKS 1 /* ! second bank contains u-boot */ |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_MONITOR_BASE 0xFFFC0000 |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ |
| #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ |
| |
| /*----------------------------------------------------------------------- |
| * Environment Variable setup |
| */ |
| #if 1 /* test-only */ |
| #define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ |
| #define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */ |
| #define CONFIG_ENV_SIZE 0x700 /* 2048 bytes may be used for env vars*/ |
| /* total size of a CAT24WC16 is 2048 bytes */ |
| |
| #else /* DEFAULT: environment in flash, using redundand flash sectors */ |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ |
| #define CONFIG_ENV_ADDR 0xFFFA0000 /* environment starts before u-boot */ |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k bytes may be used for env vars*/ |
| |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * I2C EEPROM (CAT24WC16) for environment |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_PPC4XX |
| #define CONFIG_SYS_I2C_PPC4XX_CH0 |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 |
| #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT24WC08 */ |
| /* CAT24WC08/16... */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| /* mask of address bits that overflow into the "EEPROM chip address" */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ |
| /* 16 byte page write mode using*/ |
| /* last 4 bits of the address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ |
| |
| /*----------------------------------------------------------------------- |
| * External Bus Controller (EBC) Setup |
| */ |
| |
| /* Memory Bank 0 (Intel Strata Flash) initialization */ |
| #define CONFIG_SYS_EBC_PB0AP 0x92015480 |
| #define CONFIG_SYS_EBC_PB0CR 0xFF87A000 /* BAS=0xFF8,BS=08MB,BU=R/W,BW=16bit*/ |
| |
| /* Memory Bank 1 ( Power TAU) initialization */ |
| /* #define CONFIG_SYS_EBC_PB1AP 0x04041000 */ |
| /* #define CONFIG_SYS_EBC_PB1CR 0xF0018000 */ /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ |
| #define CONFIG_SYS_EBC_PB1AP 0x00000000 |
| #define CONFIG_SYS_EBC_PB1CR 0x00000000 |
| |
| /* Memory Bank 2 (Intel Flash) initialization */ |
| #define CONFIG_SYS_EBC_PB2AP 0x00000000 |
| #define CONFIG_SYS_EBC_PB2CR 0x00000000 |
| |
| /* Memory Bank 3 (NAND) initialization */ |
| #define CONFIG_SYS_EBC_PB3AP 0x92015480 |
| #define CONFIG_SYS_EBC_PB3CR 0xF40B8000 /*addr 0xF40, BS=32M,BU=R/W, BW=8bit */ |
| |
| /* Memory Bank 4 (FPGA regs) initialization */ |
| #define CONFIG_SYS_EBC_PB4AP 0x00000000 |
| #define CONFIG_SYS_EBC_PB4CR 0x00000000 /* leave it blank */ |
| |
| #define CONFIG_SYS_NAND_BASE 0xF4000000 |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in data cache) |
| */ |
| /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ |
| #define CONFIG_SYS_TEMP_STACK_OCM 1 |
| |
| /* On Chip Memory location */ |
| #define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 |
| #define CONFIG_SYS_OCM_DATA_SIZE 0x1000 |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ |
| #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for GPIO setup (PPC405EP specific) |
| * |
| * GPIO0[0] - External Bus Controller BLAST output |
| * GPIO0[1-9] - Instruction trace outputs |
| * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs |
| * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs |
| * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs |
| * GPIO0[24-27] - UART0 control signal inputs/outputs |
| * GPIO0[28-29] - UART1 data signal input/output |
| * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs |
| * |
| * following GPIO setting changed for G20000, 080304 |
| */ |
| #define CONFIG_SYS_GPIO0_OSRL 0x40005555 |
| #define CONFIG_SYS_GPIO0_OSRH 0x40000110 |
| #define CONFIG_SYS_GPIO0_ISR1L 0x00000000 |
| #define CONFIG_SYS_GPIO0_ISR1H 0x15555445 |
| #define CONFIG_SYS_GPIO0_TSRL 0x00000000 |
| #define CONFIG_SYS_GPIO0_TSRH 0x00000000 |
| #define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 |
| |
| /* |
| * Default speed selection (cpu_plb_opb_ebc) in mhz. |
| * This value will be set if iic boot eprom is disabled. |
| */ |
| #if 1 |
| #define PLLMR0_DEFAULT PLLMR0_266_66_33_33 |
| #define PLLMR1_DEFAULT PLLMR1_266_66_33_33 |
| #endif |
| #if 0 |
| #define PLLMR0_DEFAULT PLLMR0_266_133_66_33 |
| #define PLLMR1_DEFAULT PLLMR1_266_133_66_33 |
| #endif |
| #if 0 |
| #define PLLMR0_DEFAULT PLLMR0_200_100_50_33 |
| #define PLLMR1_DEFAULT PLLMR1_200_100_50_33 |
| #endif |
| #if 0 |
| #define PLLMR0_DEFAULT PLLMR0_133_66_66_33 |
| #define PLLMR1_DEFAULT PLLMR1_133_66_66_33 |
| #endif |
| |
| #endif /* __CONFIG_H */ |