| /* |
| * (C) Copyright 2010 |
| * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * Designware ethernet IP driver for U-Boot |
| */ |
| |
| #include <common.h> |
| #include <dm.h> |
| #include <errno.h> |
| #include <miiphy.h> |
| #include <malloc.h> |
| #include <pci.h> |
| #include <linux/compiler.h> |
| #include <linux/err.h> |
| #include <asm/io.h> |
| #include "designware.h" |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| static int dw_mdio_read(struct mii_dev *bus, int addr, int devad, int reg) |
| { |
| struct eth_mac_regs *mac_p = bus->priv; |
| ulong start; |
| u16 miiaddr; |
| int timeout = CONFIG_MDIO_TIMEOUT; |
| |
| miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | |
| ((reg << MIIREGSHIFT) & MII_REGMSK); |
| |
| writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr); |
| |
| start = get_timer(0); |
| while (get_timer(start) < timeout) { |
| if (!(readl(&mac_p->miiaddr) & MII_BUSY)) |
| return readl(&mac_p->miidata); |
| udelay(10); |
| }; |
| |
| return -ETIMEDOUT; |
| } |
| |
| static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg, |
| u16 val) |
| { |
| struct eth_mac_regs *mac_p = bus->priv; |
| ulong start; |
| u16 miiaddr; |
| int ret = -ETIMEDOUT, timeout = CONFIG_MDIO_TIMEOUT; |
| |
| writel(val, &mac_p->miidata); |
| miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | |
| ((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE; |
| |
| writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr); |
| |
| start = get_timer(0); |
| while (get_timer(start) < timeout) { |
| if (!(readl(&mac_p->miiaddr) & MII_BUSY)) { |
| ret = 0; |
| break; |
| } |
| udelay(10); |
| }; |
| |
| return ret; |
| } |
| |
| static int dw_mdio_init(const char *name, struct eth_mac_regs *mac_regs_p) |
| { |
| struct mii_dev *bus = mdio_alloc(); |
| |
| if (!bus) { |
| printf("Failed to allocate MDIO bus\n"); |
| return -ENOMEM; |
| } |
| |
| bus->read = dw_mdio_read; |
| bus->write = dw_mdio_write; |
| snprintf(bus->name, sizeof(bus->name), "%s", name); |
| |
| bus->priv = (void *)mac_regs_p; |
| |
| return mdio_register(bus); |
| } |
| |
| static void tx_descs_init(struct dw_eth_dev *priv) |
| { |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| struct dmamacdescr *desc_table_p = &priv->tx_mac_descrtable[0]; |
| char *txbuffs = &priv->txbuffs[0]; |
| struct dmamacdescr *desc_p; |
| u32 idx; |
| |
| for (idx = 0; idx < CONFIG_TX_DESCR_NUM; idx++) { |
| desc_p = &desc_table_p[idx]; |
| desc_p->dmamac_addr = &txbuffs[idx * CONFIG_ETH_BUFSIZE]; |
| desc_p->dmamac_next = &desc_table_p[idx + 1]; |
| |
| #if defined(CONFIG_DW_ALTDESCRIPTOR) |
| desc_p->txrx_status &= ~(DESC_TXSTS_TXINT | DESC_TXSTS_TXLAST | |
| DESC_TXSTS_TXFIRST | DESC_TXSTS_TXCRCDIS | |
| DESC_TXSTS_TXCHECKINSCTRL | |
| DESC_TXSTS_TXRINGEND | DESC_TXSTS_TXPADDIS); |
| |
| desc_p->txrx_status |= DESC_TXSTS_TXCHAIN; |
| desc_p->dmamac_cntl = 0; |
| desc_p->txrx_status &= ~(DESC_TXSTS_MSK | DESC_TXSTS_OWNBYDMA); |
| #else |
| desc_p->dmamac_cntl = DESC_TXCTRL_TXCHAIN; |
| desc_p->txrx_status = 0; |
| #endif |
| } |
| |
| /* Correcting the last pointer of the chain */ |
| desc_p->dmamac_next = &desc_table_p[0]; |
| |
| /* Flush all Tx buffer descriptors at once */ |
| flush_dcache_range((unsigned int)priv->tx_mac_descrtable, |
| (unsigned int)priv->tx_mac_descrtable + |
| sizeof(priv->tx_mac_descrtable)); |
| |
| writel((ulong)&desc_table_p[0], &dma_p->txdesclistaddr); |
| priv->tx_currdescnum = 0; |
| } |
| |
| static void rx_descs_init(struct dw_eth_dev *priv) |
| { |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| struct dmamacdescr *desc_table_p = &priv->rx_mac_descrtable[0]; |
| char *rxbuffs = &priv->rxbuffs[0]; |
| struct dmamacdescr *desc_p; |
| u32 idx; |
| |
| /* Before passing buffers to GMAC we need to make sure zeros |
| * written there right after "priv" structure allocation were |
| * flushed into RAM. |
| * Otherwise there's a chance to get some of them flushed in RAM when |
| * GMAC is already pushing data to RAM via DMA. This way incoming from |
| * GMAC data will be corrupted. */ |
| flush_dcache_range((unsigned int)rxbuffs, (unsigned int)rxbuffs + |
| RX_TOTAL_BUFSIZE); |
| |
| for (idx = 0; idx < CONFIG_RX_DESCR_NUM; idx++) { |
| desc_p = &desc_table_p[idx]; |
| desc_p->dmamac_addr = &rxbuffs[idx * CONFIG_ETH_BUFSIZE]; |
| desc_p->dmamac_next = &desc_table_p[idx + 1]; |
| |
| desc_p->dmamac_cntl = |
| (MAC_MAX_FRAME_SZ & DESC_RXCTRL_SIZE1MASK) | |
| DESC_RXCTRL_RXCHAIN; |
| |
| desc_p->txrx_status = DESC_RXSTS_OWNBYDMA; |
| } |
| |
| /* Correcting the last pointer of the chain */ |
| desc_p->dmamac_next = &desc_table_p[0]; |
| |
| /* Flush all Rx buffer descriptors at once */ |
| flush_dcache_range((unsigned int)priv->rx_mac_descrtable, |
| (unsigned int)priv->rx_mac_descrtable + |
| sizeof(priv->rx_mac_descrtable)); |
| |
| writel((ulong)&desc_table_p[0], &dma_p->rxdesclistaddr); |
| priv->rx_currdescnum = 0; |
| } |
| |
| static int _dw_write_hwaddr(struct dw_eth_dev *priv, u8 *mac_id) |
| { |
| struct eth_mac_regs *mac_p = priv->mac_regs_p; |
| u32 macid_lo, macid_hi; |
| |
| macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) + |
| (mac_id[3] << 24); |
| macid_hi = mac_id[4] + (mac_id[5] << 8); |
| |
| writel(macid_hi, &mac_p->macaddr0hi); |
| writel(macid_lo, &mac_p->macaddr0lo); |
| |
| return 0; |
| } |
| |
| static void dw_adjust_link(struct eth_mac_regs *mac_p, |
| struct phy_device *phydev) |
| { |
| u32 conf = readl(&mac_p->conf) | FRAMEBURSTENABLE | DISABLERXOWN; |
| |
| if (!phydev->link) { |
| printf("%s: No link.\n", phydev->dev->name); |
| return; |
| } |
| |
| if (phydev->speed != 1000) |
| conf |= MII_PORTSELECT; |
| else |
| conf &= ~MII_PORTSELECT; |
| |
| if (phydev->speed == 100) |
| conf |= FES_100; |
| |
| if (phydev->duplex) |
| conf |= FULLDPLXMODE; |
| |
| writel(conf, &mac_p->conf); |
| |
| printf("Speed: %d, %s duplex%s\n", phydev->speed, |
| (phydev->duplex) ? "full" : "half", |
| (phydev->port == PORT_FIBRE) ? ", fiber mode" : ""); |
| } |
| |
| static void _dw_eth_halt(struct dw_eth_dev *priv) |
| { |
| struct eth_mac_regs *mac_p = priv->mac_regs_p; |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| |
| writel(readl(&mac_p->conf) & ~(RXENABLE | TXENABLE), &mac_p->conf); |
| writel(readl(&dma_p->opmode) & ~(RXSTART | TXSTART), &dma_p->opmode); |
| |
| phy_shutdown(priv->phydev); |
| } |
| |
| static int _dw_eth_init(struct dw_eth_dev *priv, u8 *enetaddr) |
| { |
| struct eth_mac_regs *mac_p = priv->mac_regs_p; |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| unsigned int start; |
| int ret; |
| |
| writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode); |
| |
| start = get_timer(0); |
| while (readl(&dma_p->busmode) & DMAMAC_SRST) { |
| if (get_timer(start) >= CONFIG_MACRESET_TIMEOUT) { |
| printf("DMA reset timeout\n"); |
| return -ETIMEDOUT; |
| } |
| |
| mdelay(100); |
| }; |
| |
| /* |
| * Soft reset above clears HW address registers. |
| * So we have to set it here once again. |
| */ |
| _dw_write_hwaddr(priv, enetaddr); |
| |
| rx_descs_init(priv); |
| tx_descs_init(priv); |
| |
| writel(FIXEDBURST | PRIORXTX_41 | DMA_PBL, &dma_p->busmode); |
| |
| #ifndef CONFIG_DW_MAC_FORCE_THRESHOLD_MODE |
| writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD, |
| &dma_p->opmode); |
| #else |
| writel(readl(&dma_p->opmode) | FLUSHTXFIFO, |
| &dma_p->opmode); |
| #endif |
| |
| writel(readl(&dma_p->opmode) | RXSTART | TXSTART, &dma_p->opmode); |
| |
| #ifdef CONFIG_DW_AXI_BURST_LEN |
| writel((CONFIG_DW_AXI_BURST_LEN & 0x1FF >> 1), &dma_p->axibus); |
| #endif |
| |
| /* Start up the PHY */ |
| ret = phy_startup(priv->phydev); |
| if (ret) { |
| printf("Could not initialize PHY %s\n", |
| priv->phydev->dev->name); |
| return ret; |
| } |
| |
| dw_adjust_link(mac_p, priv->phydev); |
| |
| if (!priv->phydev->link) |
| return -EIO; |
| |
| writel(readl(&mac_p->conf) | RXENABLE | TXENABLE, &mac_p->conf); |
| |
| return 0; |
| } |
| |
| static int _dw_eth_send(struct dw_eth_dev *priv, void *packet, int length) |
| { |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| u32 desc_num = priv->tx_currdescnum; |
| struct dmamacdescr *desc_p = &priv->tx_mac_descrtable[desc_num]; |
| uint32_t desc_start = (uint32_t)desc_p; |
| uint32_t desc_end = desc_start + |
| roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); |
| uint32_t data_start = (uint32_t)desc_p->dmamac_addr; |
| uint32_t data_end = data_start + |
| roundup(length, ARCH_DMA_MINALIGN); |
| /* |
| * Strictly we only need to invalidate the "txrx_status" field |
| * for the following check, but on some platforms we cannot |
| * invalidate only 4 bytes, so we flush the entire descriptor, |
| * which is 16 bytes in total. This is safe because the |
| * individual descriptors in the array are each aligned to |
| * ARCH_DMA_MINALIGN and padded appropriately. |
| */ |
| invalidate_dcache_range(desc_start, desc_end); |
| |
| /* Check if the descriptor is owned by CPU */ |
| if (desc_p->txrx_status & DESC_TXSTS_OWNBYDMA) { |
| printf("CPU not owner of tx frame\n"); |
| return -EPERM; |
| } |
| |
| memcpy(desc_p->dmamac_addr, packet, length); |
| |
| /* Flush data to be sent */ |
| flush_dcache_range(data_start, data_end); |
| |
| #if defined(CONFIG_DW_ALTDESCRIPTOR) |
| desc_p->txrx_status |= DESC_TXSTS_TXFIRST | DESC_TXSTS_TXLAST; |
| desc_p->dmamac_cntl |= (length << DESC_TXCTRL_SIZE1SHFT) & |
| DESC_TXCTRL_SIZE1MASK; |
| |
| desc_p->txrx_status &= ~(DESC_TXSTS_MSK); |
| desc_p->txrx_status |= DESC_TXSTS_OWNBYDMA; |
| #else |
| desc_p->dmamac_cntl |= ((length << DESC_TXCTRL_SIZE1SHFT) & |
| DESC_TXCTRL_SIZE1MASK) | DESC_TXCTRL_TXLAST | |
| DESC_TXCTRL_TXFIRST; |
| |
| desc_p->txrx_status = DESC_TXSTS_OWNBYDMA; |
| #endif |
| |
| /* Flush modified buffer descriptor */ |
| flush_dcache_range(desc_start, desc_end); |
| |
| /* Test the wrap-around condition. */ |
| if (++desc_num >= CONFIG_TX_DESCR_NUM) |
| desc_num = 0; |
| |
| priv->tx_currdescnum = desc_num; |
| |
| /* Start the transmission */ |
| writel(POLL_DATA, &dma_p->txpolldemand); |
| |
| return 0; |
| } |
| |
| static int _dw_eth_recv(struct dw_eth_dev *priv, uchar **packetp) |
| { |
| u32 status, desc_num = priv->rx_currdescnum; |
| struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num]; |
| int length = -EAGAIN; |
| uint32_t desc_start = (uint32_t)desc_p; |
| uint32_t desc_end = desc_start + |
| roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); |
| uint32_t data_start = (uint32_t)desc_p->dmamac_addr; |
| uint32_t data_end; |
| |
| /* Invalidate entire buffer descriptor */ |
| invalidate_dcache_range(desc_start, desc_end); |
| |
| status = desc_p->txrx_status; |
| |
| /* Check if the owner is the CPU */ |
| if (!(status & DESC_RXSTS_OWNBYDMA)) { |
| |
| length = (status & DESC_RXSTS_FRMLENMSK) >> |
| DESC_RXSTS_FRMLENSHFT; |
| |
| /* Invalidate received data */ |
| data_end = data_start + roundup(length, ARCH_DMA_MINALIGN); |
| invalidate_dcache_range(data_start, data_end); |
| *packetp = desc_p->dmamac_addr; |
| } |
| |
| return length; |
| } |
| |
| static int _dw_free_pkt(struct dw_eth_dev *priv) |
| { |
| u32 desc_num = priv->rx_currdescnum; |
| struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num]; |
| uint32_t desc_start = (uint32_t)desc_p; |
| uint32_t desc_end = desc_start + |
| roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); |
| |
| /* |
| * Make the current descriptor valid again and go to |
| * the next one |
| */ |
| desc_p->txrx_status |= DESC_RXSTS_OWNBYDMA; |
| |
| /* Flush only status field - others weren't changed */ |
| flush_dcache_range(desc_start, desc_end); |
| |
| /* Test the wrap-around condition. */ |
| if (++desc_num >= CONFIG_RX_DESCR_NUM) |
| desc_num = 0; |
| priv->rx_currdescnum = desc_num; |
| |
| return 0; |
| } |
| |
| static int dw_phy_init(struct dw_eth_dev *priv, void *dev) |
| { |
| struct phy_device *phydev; |
| int mask = 0xffffffff, ret; |
| |
| #ifdef CONFIG_PHY_ADDR |
| mask = 1 << CONFIG_PHY_ADDR; |
| #endif |
| |
| phydev = phy_find_by_mask(priv->bus, mask, priv->interface); |
| if (!phydev) |
| return -ENODEV; |
| |
| phy_connect_dev(phydev, dev); |
| |
| phydev->supported &= PHY_GBIT_FEATURES; |
| if (priv->max_speed) { |
| ret = phy_set_supported(phydev, priv->max_speed); |
| if (ret) |
| return ret; |
| } |
| phydev->advertising = phydev->supported; |
| |
| priv->phydev = phydev; |
| phy_config(phydev); |
| |
| return 0; |
| } |
| |
| #ifndef CONFIG_DM_ETH |
| static int dw_eth_init(struct eth_device *dev, bd_t *bis) |
| { |
| return _dw_eth_init(dev->priv, dev->enetaddr); |
| } |
| |
| static int dw_eth_send(struct eth_device *dev, void *packet, int length) |
| { |
| return _dw_eth_send(dev->priv, packet, length); |
| } |
| |
| static int dw_eth_recv(struct eth_device *dev) |
| { |
| uchar *packet; |
| int length; |
| |
| length = _dw_eth_recv(dev->priv, &packet); |
| if (length == -EAGAIN) |
| return 0; |
| net_process_received_packet(packet, length); |
| |
| _dw_free_pkt(dev->priv); |
| |
| return 0; |
| } |
| |
| static void dw_eth_halt(struct eth_device *dev) |
| { |
| return _dw_eth_halt(dev->priv); |
| } |
| |
| static int dw_write_hwaddr(struct eth_device *dev) |
| { |
| return _dw_write_hwaddr(dev->priv, dev->enetaddr); |
| } |
| |
| int designware_initialize(ulong base_addr, u32 interface) |
| { |
| struct eth_device *dev; |
| struct dw_eth_dev *priv; |
| |
| dev = (struct eth_device *) malloc(sizeof(struct eth_device)); |
| if (!dev) |
| return -ENOMEM; |
| |
| /* |
| * Since the priv structure contains the descriptors which need a strict |
| * buswidth alignment, memalign is used to allocate memory |
| */ |
| priv = (struct dw_eth_dev *) memalign(ARCH_DMA_MINALIGN, |
| sizeof(struct dw_eth_dev)); |
| if (!priv) { |
| free(dev); |
| return -ENOMEM; |
| } |
| |
| memset(dev, 0, sizeof(struct eth_device)); |
| memset(priv, 0, sizeof(struct dw_eth_dev)); |
| |
| sprintf(dev->name, "dwmac.%lx", base_addr); |
| dev->iobase = (int)base_addr; |
| dev->priv = priv; |
| |
| priv->dev = dev; |
| priv->mac_regs_p = (struct eth_mac_regs *)base_addr; |
| priv->dma_regs_p = (struct eth_dma_regs *)(base_addr + |
| DW_DMA_BASE_OFFSET); |
| |
| dev->init = dw_eth_init; |
| dev->send = dw_eth_send; |
| dev->recv = dw_eth_recv; |
| dev->halt = dw_eth_halt; |
| dev->write_hwaddr = dw_write_hwaddr; |
| |
| eth_register(dev); |
| |
| priv->interface = interface; |
| |
| dw_mdio_init(dev->name, priv->mac_regs_p); |
| priv->bus = miiphy_get_dev_by_name(dev->name); |
| |
| return dw_phy_init(priv, dev); |
| } |
| #endif |
| |
| #ifdef CONFIG_DM_ETH |
| static int designware_eth_start(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| |
| return _dw_eth_init(dev->priv, pdata->enetaddr); |
| } |
| |
| static int designware_eth_send(struct udevice *dev, void *packet, int length) |
| { |
| struct dw_eth_dev *priv = dev_get_priv(dev); |
| |
| return _dw_eth_send(priv, packet, length); |
| } |
| |
| static int designware_eth_recv(struct udevice *dev, int flags, uchar **packetp) |
| { |
| struct dw_eth_dev *priv = dev_get_priv(dev); |
| |
| return _dw_eth_recv(priv, packetp); |
| } |
| |
| static int designware_eth_free_pkt(struct udevice *dev, uchar *packet, |
| int length) |
| { |
| struct dw_eth_dev *priv = dev_get_priv(dev); |
| |
| return _dw_free_pkt(priv); |
| } |
| |
| static void designware_eth_stop(struct udevice *dev) |
| { |
| struct dw_eth_dev *priv = dev_get_priv(dev); |
| |
| return _dw_eth_halt(priv); |
| } |
| |
| static int designware_eth_write_hwaddr(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| struct dw_eth_dev *priv = dev_get_priv(dev); |
| |
| return _dw_write_hwaddr(priv, pdata->enetaddr); |
| } |
| |
| static int designware_eth_bind(struct udevice *dev) |
| { |
| #ifdef CONFIG_DM_PCI |
| static int num_cards; |
| char name[20]; |
| |
| /* Create a unique device name for PCI type devices */ |
| if (device_is_on_pci_bus(dev)) { |
| sprintf(name, "eth_designware#%u", num_cards++); |
| device_set_name(dev, name); |
| } |
| #endif |
| |
| return 0; |
| } |
| |
| static int designware_eth_probe(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| struct dw_eth_dev *priv = dev_get_priv(dev); |
| u32 iobase = pdata->iobase; |
| int ret; |
| |
| #ifdef CONFIG_DM_PCI |
| /* |
| * If we are on PCI bus, either directly attached to a PCI root port, |
| * or via a PCI bridge, fill in platdata before we probe the hardware. |
| */ |
| if (device_is_on_pci_bus(dev)) { |
| dm_pci_read_config32(dev, PCI_BASE_ADDRESS_0, &iobase); |
| iobase &= PCI_BASE_ADDRESS_MEM_MASK; |
| iobase = dm_pci_mem_to_phys(dev, iobase); |
| |
| pdata->iobase = iobase; |
| pdata->phy_interface = PHY_INTERFACE_MODE_RMII; |
| } |
| #endif |
| |
| debug("%s, iobase=%x, priv=%p\n", __func__, iobase, priv); |
| priv->mac_regs_p = (struct eth_mac_regs *)iobase; |
| priv->dma_regs_p = (struct eth_dma_regs *)(iobase + DW_DMA_BASE_OFFSET); |
| priv->interface = pdata->phy_interface; |
| priv->max_speed = pdata->max_speed; |
| |
| dw_mdio_init(dev->name, priv->mac_regs_p); |
| priv->bus = miiphy_get_dev_by_name(dev->name); |
| |
| ret = dw_phy_init(priv, dev); |
| debug("%s, ret=%d\n", __func__, ret); |
| |
| return ret; |
| } |
| |
| static int designware_eth_remove(struct udevice *dev) |
| { |
| struct dw_eth_dev *priv = dev_get_priv(dev); |
| |
| free(priv->phydev); |
| mdio_unregister(priv->bus); |
| mdio_free(priv->bus); |
| |
| return 0; |
| } |
| |
| static const struct eth_ops designware_eth_ops = { |
| .start = designware_eth_start, |
| .send = designware_eth_send, |
| .recv = designware_eth_recv, |
| .free_pkt = designware_eth_free_pkt, |
| .stop = designware_eth_stop, |
| .write_hwaddr = designware_eth_write_hwaddr, |
| }; |
| |
| static int designware_eth_ofdata_to_platdata(struct udevice *dev) |
| { |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| const char *phy_mode; |
| const fdt32_t *cell; |
| |
| pdata->iobase = dev_get_addr(dev); |
| pdata->phy_interface = -1; |
| phy_mode = fdt_getprop(gd->fdt_blob, dev->of_offset, "phy-mode", NULL); |
| if (phy_mode) |
| pdata->phy_interface = phy_get_interface_by_name(phy_mode); |
| if (pdata->phy_interface == -1) { |
| debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode); |
| return -EINVAL; |
| } |
| |
| pdata->max_speed = 0; |
| cell = fdt_getprop(gd->fdt_blob, dev->of_offset, "max-speed", NULL); |
| if (cell) |
| pdata->max_speed = fdt32_to_cpu(*cell); |
| |
| return 0; |
| } |
| |
| static const struct udevice_id designware_eth_ids[] = { |
| { .compatible = "allwinner,sun7i-a20-gmac" }, |
| { .compatible = "altr,socfpga-stmmac" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(eth_designware) = { |
| .name = "eth_designware", |
| .id = UCLASS_ETH, |
| .of_match = designware_eth_ids, |
| .ofdata_to_platdata = designware_eth_ofdata_to_platdata, |
| .bind = designware_eth_bind, |
| .probe = designware_eth_probe, |
| .remove = designware_eth_remove, |
| .ops = &designware_eth_ops, |
| .priv_auto_alloc_size = sizeof(struct dw_eth_dev), |
| .platdata_auto_alloc_size = sizeof(struct eth_pdata), |
| .flags = DM_FLAG_ALLOC_PRIV_DMA, |
| }; |
| |
| static struct pci_device_id supported[] = { |
| { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_QRK_EMAC) }, |
| { } |
| }; |
| |
| U_BOOT_PCI_DEVICE(eth_designware, supported); |
| #endif |