blob: 39ca7930baf81d537fe00ca5ed58c886ccd594e5 [file] [log] [blame]
/*
* (C) Copyright 2010
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* t3corp.h - configuration for T3CORP (460GT)
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_460GT 1 /* Specific PPC460GT */
#define CONFIG_440 1
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_HOSTNAME t3corp
/*
* Include common defines/options for all AMCC/APM eval boards
*/
#include "amcc-common.h"
#define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_BOARD_TYPES 1 /* support board types */
#define CONFIG_FIT
#define CFG_ALT_MEMTEST
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
#define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE
#define CONFIG_SYS_PCIE_MEMBASE 0xb0000000 /* mapped PCIe mem */
#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* incr for PCIe */
#define CONFIG_SYS_PCIE_BASE 0xc4000000 /* PCIe UTL regs */
#define CONFIG_SYS_PCIE0_CFGBASE 0xc0000000
#define CONFIG_SYS_PCIE1_CFGBASE 0xc1000000
#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000
#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000
#define CONFIG_SYS_PCIE0_UTLBASE 0xc08010000ULL /* 36bit phys addr */
/* base address of inbound PCIe window */
#define CONFIG_SYS_PCIE_INBOUND_BASE 0x000000000ULL /* 36bit phys addr */
/* EBC stuff */
#define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped here */
#define CONFIG_SYS_FLASH_SIZE (64 << 20)
#define CONFIG_SYS_FPGA1_BASE 0xe0000000
#define CONFIG_SYS_FPGA2_BASE 0xe2000000
#define CONFIG_SYS_FPGA3_BASE 0xe4000000
#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space */
#define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4
#define CONFIG_SYS_FLASH_BASE_PHYS_L 0xCC000000
#define CONFIG_SYS_FLASH_BASE_PHYS \
(((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) \
| (u64)CONFIG_SYS_FLASH_BASE_PHYS_L)
#define CONFIG_SYS_OCM_BASE 0xE7000000 /* OCM: 64k */
#define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */
#define CONFIG_SYS_SRAM_SIZE (256 << 10)
#define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000
/*
* Initial RAM & stack pointer (placed in OCM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
#define CONFIG_SYS_INIT_RAM_END (4 << 10)
#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET \
(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
/*
* Environment
*/
/*
* Define here the location of the environment variables (flash).
*/
#define CONFIG_ENV_IS_IN_FLASH /* use flash for environment vars */
/*
* Flash related
*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* Use AMD reset cmd */
#define CONFIG_SYS_CFI_FLASH_STATUS_POLL /* use status poll method */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sectors p. chip*/
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase/ms*/
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write/ms*/
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buff'd writes (20x faster)*/
#define CONFIG_SYS_FLASH_EMPTY_INFO /* 'E' for empty sector on flinfo */
#define CONFIG_ENV_SECT_SIZE 0x20000 /* sector size */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - \
CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x4000 /* env sector size */
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
/*
* DDR2 SDRAM
*/
#define CONFIG_SYS_MBYTES_SDRAM 256
#define CONFIG_DDR_ECC
#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */
#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */
#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */
#undef CONFIG_PPC4xx_DDR_METHOD_A
#define CONFIG_DDR_RFDC_FIXED 0x000001D7 /* optimal value */
/* DDR1/2 SDRAM Device Control Register Data Values */
/* Memory Queue */
#define CONFIG_SYS_SDRAM_R0BAS (SDRAM_RXBAS_SDBA_ENCODE(0) | \
SDRAM_RXBAS_SDSZ_256)
#define CONFIG_SYS_SDRAM_R1BAS 0x00000000
#define CONFIG_SYS_SDRAM_R2BAS 0x00000000
#define CONFIG_SYS_SDRAM_R3BAS 0x00000000
#define CONFIG_SYS_SDRAM_PLBADDULL 0x00000000
#define CONFIG_SYS_SDRAM_PLBADDUHB 0x00000008
#define CONFIG_SYS_SDRAM_CONF1LL 0x80001C00
#define CONFIG_SYS_SDRAM_CONF1HB 0x80001C80
#define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000
#define CAS_LATENCY JEDEC_MA_MR_CL_DDR2_5_0_CLK
/* DDR1/2 SDRAM Device Control Register Data Values */
#define CONFIG_SYS_SDRAM0_MB0CF (SDRAM_RXBAS_SDAM_MODE7 | \
SDRAM_RXBAS_SDBE_ENABLE)
#define CONFIG_SYS_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE
#define CONFIG_SYS_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
#define CONFIG_SYS_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
#define CONFIG_SYS_SDRAM0_MCOPT1 (SDRAM_MCOPT1_MCHK_GEN | \
SDRAM_MCOPT1_PMU_OPEN | \
SDRAM_MCOPT1_DMWD_32 | \
SDRAM_MCOPT1_8_BANKS | \
SDRAM_MCOPT1_DDR2_TYPE | \
SDRAM_MCOPT1_QDEP | \
SDRAM_MCOPT1_RWOO_DISABLED | \
SDRAM_MCOPT1_WOOO_DISABLED | \
SDRAM_MCOPT1_DREF_NORMAL)
#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000
#define CONFIG_SYS_SDRAM0_MODT0 SDRAM_MODT_EB0W_ENABLE
#define CONFIG_SYS_SDRAM0_MODT1 0x00000000
#define CONFIG_SYS_SDRAM0_MODT2 0x00000000
#define CONFIG_SYS_SDRAM0_MODT3 0x00000000
#define CONFIG_SYS_SDRAM0_CODT (SDRAM_CODT_RK0R_ON | \
SDRAM_CODT_DQS_1_8_V_DDR2 | \
SDRAM_CODT_IO_NMODE)
#define CONFIG_SYS_SDRAM0_RTR SDRAM_RTR_RINT_ENCODE(1560)
#define CONFIG_SYS_SDRAM0_INITPLR0 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(80) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_NOP))
#define CONFIG_SYS_SDRAM0_INITPLR1 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(3) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
#define CONFIG_SYS_SDRAM0_INITPLR2 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR2) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR2_TEMP_COMMERCIAL))
#define CONFIG_SYS_SDRAM0_INITPLR3 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR3) | \
SDRAM_INITPLR_IMA_ENCODE(0))
#define CONFIG_SYS_SDRAM0_INITPLR4 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_DQS_ENABLE | \
JEDEC_MA_EMR_RTT_150OHM))
#define CONFIG_SYS_SDRAM0_INITPLR5 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(200) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \
CAS_LATENCY | \
JEDEC_MA_MR_BLEN_4 | \
JEDEC_MA_MR_DLL_RESET))
#define CONFIG_SYS_SDRAM0_INITPLR6 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(3) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \
SDRAM_INITPLR_IBA_ENCODE(0x0) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL))
#define CONFIG_SYS_SDRAM0_INITPLR7 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(26) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
#define CONFIG_SYS_SDRAM0_INITPLR8 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(26) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
#define CONFIG_SYS_SDRAM0_INITPLR9 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(26) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
#define CONFIG_SYS_SDRAM0_INITPLR10 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(26) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH))
#define CONFIG_SYS_SDRAM0_INITPLR11 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \
CAS_LATENCY | \
JEDEC_MA_MR_BLEN_4))
#define CONFIG_SYS_SDRAM0_INITPLR12 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_ENTER | \
JEDEC_MA_EMR_RDQS_DISABLE | \
JEDEC_MA_EMR_DQS_ENABLE | \
JEDEC_MA_EMR_RTT_150OHM | \
JEDEC_MA_EMR_ODS_NORMAL))
#define CONFIG_SYS_SDRAM0_INITPLR13 \
(SDRAM_INITPLR_ENABLE | \
SDRAM_INITPLR_IMWT_ENCODE(2) | \
SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \
SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \
SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_OCD_EXIT | \
JEDEC_MA_EMR_RDQS_DISABLE | \
JEDEC_MA_EMR_DQS_ENABLE | \
JEDEC_MA_EMR_RTT_150OHM | \
JEDEC_MA_EMR_ODS_NORMAL))
#define CONFIG_SYS_SDRAM0_INITPLR14 SDRAM_INITPLR_DISABLE
#define CONFIG_SYS_SDRAM0_INITPLR15 SDRAM_INITPLR_DISABLE
#define CONFIG_SYS_SDRAM0_RQDC (SDRAM_RQDC_RQDE_ENABLE | \
SDRAM_RQDC_RQFD_ENCODE(56))
#define CONFIG_SYS_SDRAM0_RFDC SDRAM_RFDC_RFFD_ENCODE(599)
#define CONFIG_SYS_SDRAM0_RDCC (SDRAM_RDCC_RDSS_T2)
#define CONFIG_SYS_SDRAM0_DLCR (SDRAM_DLCR_DCLM_AUTO | \
SDRAM_DLCR_DLCS_CONT_DONE | \
SDRAM_DLCR_DLCV_ENCODE(155))
#define CONFIG_SYS_SDRAM0_CLKTR SDRAM_CLKTR_CLKP_90_DEG_ADV
#define CONFIG_SYS_SDRAM0_WRDTR SDRAM_WRDTR_WTR_90_DEG_ADV
#define CONFIG_SYS_SDRAM0_SDTR1 (SDRAM_SDTR1_LDOF_2_CLK | \
SDRAM_SDTR1_RTW_2_CLK | \
SDRAM_SDTR1_RTRO_1_CLK)
#define CONFIG_SYS_SDRAM0_SDTR2 (SDRAM_SDTR2_RCD_3_CLK | \
SDRAM_SDTR2_WTR_2_CLK | \
SDRAM_SDTR2_XSNR_32_CLK | \
SDRAM_SDTR2_WPC_4_CLK | \
SDRAM_SDTR2_RPC_2_CLK | \
SDRAM_SDTR2_RP_3_CLK | \
SDRAM_SDTR2_RRD_2_CLK)
#define CONFIG_SYS_SDRAM0_SDTR3 (SDRAM_SDTR3_RAS_ENCODE(8) | \
SDRAM_SDTR3_RC_ENCODE(11) | \
SDRAM_SDTR3_XCS | \
SDRAM_SDTR3_RFC_ENCODE(26))
#define CONFIG_SYS_SDRAM0_MMODE (SDRAM_MMODE_WR_DDR2_3_CYC | \
CAS_LATENCY | \
SDRAM_MMODE_BLEN_4)
#define CONFIG_SYS_SDRAM0_MEMODE (SDRAM_MEMODE_DQS_ENABLE | \
SDRAM_MEMODE_RTT_150OHM)
/*
* I2C
*/
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed */
#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/* I2C bootstrap EEPROM */
#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52
#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0
#define CONFIG_4xx_CONFIG_BLOCKSIZE 16
/*
* Ethernet
*/
#define CONFIG_IBM_EMAC4_V4 1
#define CONFIG_HAS_ETH0
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_M88E1111_PHY
/* Disable fiber since fiber/copper auto-selection doesn't seem to work */
#define CONFIG_M88E1111_DISABLE_FIBER
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_PHY_DYNAMIC_ANEG 1
/*
* Default environment variables
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_AMCC_DEF_ENV \
CONFIG_AMCC_DEF_ENV_POWERPC \
CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
/*
* Commands additional to the ones defined in amcc-common.h
*/
#define CONFIG_CMD_CHIP_CONFIG
#define CONFIG_CMD_ECCTEST
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
/*
* PCI stuff
*/
/* General PCI */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_PCI_CONFIG_HOST_BRIDGE
/* Board-specific PCI, no PCI support, only PCIe */
#undef CONFIG_SYS_PCI_TARGET_INIT
#undef CONFIG_SYS_PCI_MASTER_INIT
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
/*
* External Bus Controller (EBC) Setup
*/
/*
* T3CORP has 64MBytes of NOR flash (Spansion 29GL512), but the
* boot EBC mapping only supports a maximum of 16MBytes
* (4.ff00.0000 - 4.ffff.ffff).
* To solve this problem, the flash has to get remapped to another
* EBC address which accepts bigger regions:
*
* 0xfc00.0000 -> 4.cc00.0000
*/
/* Memory Bank 0 (NOR-flash) */
#define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(16) | \
EBC_BXAP_BCE_DISABLE | \
EBC_BXAP_BCT_2TRANS | \
EBC_BXAP_CSN_ENCODE(1) | \
EBC_BXAP_OEN_ENCODE(1) | \
EBC_BXAP_WBN_ENCODE(1) | \
EBC_BXAP_WBF_ENCODE(1) | \
EBC_BXAP_TH_ENCODE(7) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_WRITEONLY | \
EBC_BXAP_PEN_DISABLED)
#define CONFIG_SYS_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_BOOT_BASE_ADDR) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_16BIT)
/* Memory Bank 1 (FPGA 1) */
#define CONFIG_SYS_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(5) | \
EBC_BXAP_CSN_ENCODE(0) | \
EBC_BXAP_OEN_ENCODE(3) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(1) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_RW | \
EBC_BXAP_PEN_DISABLED)
#define CONFIG_SYS_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA1_BASE) | \
EBC_BXCR_BS_32MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_32BIT)
/* Memory Bank 2 (FPGA 2) */
#define CONFIG_SYS_EBC_PB2AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(5) | \
EBC_BXAP_CSN_ENCODE(0) | \
EBC_BXAP_OEN_ENCODE(3) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(1) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_RW | \
EBC_BXAP_PEN_DISABLED)
#define CONFIG_SYS_EBC_PB2CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA2_BASE) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_32BIT)
/* Memory Bank 3 (FPGA 3) */
#define CONFIG_SYS_EBC_PB3AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(5) | \
EBC_BXAP_CSN_ENCODE(0) | \
EBC_BXAP_OEN_ENCODE(3) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(1) | \
EBC_BXAP_RE_DISABLED | \
EBC_BXAP_SOR_DELAYED | \
EBC_BXAP_BEM_RW | \
EBC_BXAP_PEN_DISABLED)
#define CONFIG_SYS_EBC_PB3CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA3_BASE) | \
EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_32BIT)
/*
* PPC4xx GPIO Configuration
*/
#define CONFIG_SYS_4xx_GPIO_TABLE { /* GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \
{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 NFCLE */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 NFALE */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO27 IRQ(0) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO28 IRQ(1) */ \
{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) */ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO30 PerPar0 DMAReq2 IRQ(7)*/ \
{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO31 PerPar1 DMAAck2 IRQ(8)*/ \
}, \
{ \
/* GPIO Core 1 */ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 PerPar2 EOT2/TC2 IRQ(9)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 PerPar3 DMAReq3 IRQ(4)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N DMAAck3 UART3_SIN*/ \
{GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EOT3/TC3 UART3_SOUT*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \
{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 PerAddr(6) DMAAck0 IRQ(14)*/ \
{GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 PerAddr(7) EOT/TC0 IRQ(15)*/ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO55 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \
{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \
} \
}
#endif /* __CONFIG_H */