include/configs/omap3_sdp3430.h - github/trini/u-boot - Gitiles

 /*
  * (C) Copyright 2006-2009
  * Texas Instruments Incorporated.
  * Richard Woodruff <r-woodruff2@ti.com>
  * Syed Mohammed Khasim <x0khasim@ti.com>
  * Nishanth Menon <nm@ti.com>
  *
  * Configuration settings for the 3430 TI SDP3430 board.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /* TODO: REMOVE THE FOLLOWING
  * Retained the following till size.h is removed in u-boot
  */
 #include <asm/sizes.h>
 /*
  * High Level Configuration Options
  */
 #define CONFIG_ARMCORTEXA8	1	/* This is an ARM V7 CPU core */
 #define CONFIG_OMAP		1	/* in a TI OMAP core */
 #define CONFIG_OMAP34XX		1	/* which is a 34XX */
 #define CONFIG_OMAP3430		1	/* which is in a 3430 */
 #define CONFIG_OMAP3_3430SDP	1	/* working with SDP Rev2 */

 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>

 /*
  * NOTE:  these #defines presume standard SDP jumper settings.
  * In particular:
  *  - 26 MHz clock (not 19.2 or 38.4 MHz)
  *  - Boot from 128MB NOR, not NAND or OneNAND
  *
  * At this writing, OMAP3 U-Boot support doesn't permit concurrent
  * support for all the flash types the board supports.
  */
 #define CONFIG_DISPLAY_CPUINFO		1
 #define CONFIG_DISPLAY_BOARDINFO	1

 /* Clock Defines */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)

 #undef CONFIG_USE_IRQ			/* no support for IRQs */
 #define CONFIG_MISC_INIT_R

 #define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS	1
 #define CONFIG_INITRD_TAG		1
 #define CONFIG_REVISION_TAG		1

 /*
  * Size of malloc() pool
  * Total Size Environment - 256k
  * Malloc - add 256k
  */
 #define CONFIG_ENV_SIZE			(256 << 10)
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (256 << 10))
 #define CONFIG_SYS_GBL_DATA_SIZE	128	/* bytes reserved for */
 						/* initial data */

 /*--------------------------------------------------------------------------*/

 /*
  * Hardware drivers
  */

 /*
  * TWL4030
  */
 #define CONFIG_TWL4030_POWER		1

 /*
  * serial port - NS16550 compatible
  */
 #define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */

 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
 #define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK

 /* Original SDP u-boot used UART1 and thus J8 (innermost); that can be
  * swapped with UART2 via jumpering.  Downsides of using J8:  it doesn't
  * support UART boot (that's only for UART3); it prevents sharing a Linux
  * kernel (LL_DEBUG_UART3) or filesystem (getty ttyS2) with most boards.
  *
  * UART boot uses UART3 on J9, and the SDP user's guide says to use
  * that for console.  Downsides of using J9:  you can't use IRDA too;
  * since UART3 isn't in the CORE power domain, it may be a bit less
  * usable in certain PM-sensitive debug scenarios.
  */
 #undef CONSOLE_J9			/* else J8/UART1 (innermost) */

 #ifdef CONSOLE_J9
 #define CONFIG_CONS_INDEX		3
 #define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
 #define CONFIG_SERIAL3			3	/* UART3 */
 #else
 #define CONFIG_CONS_INDEX		1
 #define CONFIG_SYS_NS16550_COM1		OMAP34XX_UART1
 #define CONFIG_SERIAL1			1	/* UART1 */
 #endif

 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}

 /*
  * I2C for power management setup
  */
 #define CONFIG_HARD_I2C			1
 #define CONFIG_SYS_I2C_SPEED		100000
 #define CONFIG_SYS_I2C_SLAVE		1
 #define CONFIG_SYS_I2C_BUS		0
 #define CONFIG_SYS_I2C_BUS_SELECT	1
 #define CONFIG_DRIVER_OMAP34XX_I2C	1

 /* DDR - I use Infineon DDR */
 #define CONFIG_OMAP3_INFINEON_DDR	1

 /* OMITTED:  single 1 Gbit MT29F1G NAND flash */

 /*
  * NOR boot support - single 1 Gbit PF48F6000M0 Strataflash
  */
 #define CONFIG_SYS_FLASH_BASE		0x10000000
 #define CONFIG_FLASH_CFI_DRIVER		1	/* Use drivers/cfi_flash.c */
 #define CONFIG_SYS_FLASH_CFI		1	/* use CFI geometry data */
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* ~10x faster writes */
 #define CONFIG_SYS_FLASH_PROTECTION	1	/* hardware sector protection */
 #define CONFIG_SYS_FLASH_EMPTY_INFO	1	/* flinfo 'E' for empty */
 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE}
 #define CONFIG_SYS_MAX_FLASH_BANKS      1	/* max number of flash banks */

 #define CONFIG_SYS_FLASH_CFI_WIDTH	2
 #define PHYS_FLASH_SIZE			(128 << 20)
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* max sectors on one chip */

 /* timeout values are in milliseconds */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	(100 * CONFIG_SYS_HZ)
 #define CONFIG_SYS_FLASH_WRITE_TOUT	(100 * CONFIG_SYS_HZ)

 /* OMITTED:  single 2 Gbit KFM2G16 OneNAND flash */

 #define CONFIG_ENV_IS_IN_FLASH		1
 #define CONFIG_SYS_ENV_SECT_SIZE	(256 << 10)
 #define CONFIG_ENV_OFFSET		CONFIG_SYS_ENV_SECT_SIZE
 #define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_ENV_SECT_SIZE)
 /*--------------------------------------------------------------------------*/

 /* commands to include */
 #include <config_cmd_default.h>

 /* Enabled commands */
 #define CONFIG_CMD_DHCP		/* DHCP Support			*/
 #define CONFIG_CMD_EXT2		/* EXT2 Support			*/
 #define CONFIG_CMD_FAT		/* FAT support			*/
 #define CONFIG_CMD_I2C		/* I2C serial bus support	*/
 #define CONFIG_CMD_JFFS2	/* JFFS2 Support		*/
 #define CONFIG_CMD_MMC		/* MMC support			*/
 #define CONFIG_CMD_NET

 /* Disabled commands */
 #undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
 #undef CONFIG_CMD_IMLS		/* List all found images	*/

 /*--------------------------------------------------------------------------*/
 /*
  * MMC boot support
  */

 #if defined(CONFIG_CMD_MMC)
 #define CONFIG_MMC			1
 #define CONFIG_OMAP3_MMC		1
 #define CONFIG_DOS_PARTITION		1
 #endif

 /*----------------------------------------------------------------------------
  * SMSC9115 Ethernet from SMSC9118 family
  *----------------------------------------------------------------------------
  */
 #if defined(CONFIG_CMD_NET)

 #define CONFIG_NET_MULTI
 #define CONFIG_LAN91C96
 #define CONFIG_LAN91C96_BASE	DEBUG_BASE
 #define CONFIG_LAN91C96_EXT_PHY

 #define CONFIG_BOOTP_SEND_HOSTNAME
 /*
  * BOOTP fields
  */
 #define CONFIG_BOOTP_SUBNETMASK		0x00000001
 #define CONFIG_BOOTP_GATEWAY		0x00000002
 #define CONFIG_BOOTP_HOSTNAME		0x00000004
 #define CONFIG_BOOTP_BOOTPATH		0x00000010
 #endif /* (CONFIG_CMD_NET) */

 /*
  * Environment setup
  *
  * Default boot order:  mmc bootscript, MMC uImage, NOR image.
  * Network booting environment must be configured at site.
  */

 /* allow overwriting serial config and ethaddr */
 #define CONFIG_ENV_OVERWRITE

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x82000000\0" \
 	"console=ttyS0,115200n8\0" \
 	"mmcargs=setenv bootargs console=${console} " \
 		"root=/dev/mmcblk0p2 rw " \
 		"rootfstype=ext3 rootwait\0" \
 	"norargs=setenv bootargs console=${console} " \
 		"root=/dev/mtdblock3 rw " \
 		"rootfstype=jffs2\0" \
 	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
 	"bootscript=echo Running bootscript from MMC/SD ...; " \
 		"autoscr ${loadaddr}\0" \
 	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
 	"mmcboot=echo Booting from MMC/SD ...; " \
 		"run mmcargs; " \
 		"bootm ${loadaddr}\0" \
 	"norboot=echo Booting from NOR ...; " \
 		"run norargs; " \
 		"bootm 0x80000\0" \

 #define CONFIG_BOOTCOMMAND \
 	"if mmcinit; then " \
 		"if run loadbootscript; then " \
 			"run bootscript; " \
 		"else " \
 			"if run loaduimage; then " \
 				"run mmcboot; " \
 			"else run norboot; " \
 			"fi; " \
 		"fi; " \
 	"else run norboot; fi"

 #define CONFIG_AUTO_COMPLETE		1

 /*--------------------------------------------------------------------------*/

 /*
  * Miscellaneous configurable options
  */

 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
 #define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
 #define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 #define CONFIG_SYS_PROMPT		"OMAP34XX SDP # "
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		16	/* max number of command args */
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)

 /* SDRAM Test range - start at 16 meg boundary -ends at 32Meg -
  * a basic sanity check ONLY
  * IF you would like to increase coverage, increase the end address
  * or run the test with custom options
  */
 #define CONFIG_SYS_MEMTEST_START	(OMAP34XX_SDRC_CS0 + 0x01000000)
 #define CONFIG_SYS_MEMTEST_END		(OMAP34XX_SDRC_CS0 + (32 << 20))

 /* Default load address */
 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)

 /*--------------------------------------------------------------------------*/

 /*
  * 3430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
  * 32KHz clk, or from external sig. This rate is divided by a local divisor.
  */
 #define CONFIG_SYS_TIMERBASE		(OMAP34XX_GPT2)
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
 #define CONFIG_SYS_HZ			1000

 /*
  * Stack sizes
  *
  * The stack sizes are set up in start.S using the settings below
  */
 #define CONFIG_STACKSIZE	(128 << 10) /* Regular stack */
 #ifdef CONFIG_USE_IRQ
 #define CONFIG_STACKSIZE_IRQ	(4 << 10) /* IRQ stack */
 #define CONFIG_STACKSIZE_FIQ	(4 << 10) /* FIQ stack */
 #endif

 /*
  * SDRAM Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
 #define PHYS_SDRAM_1_SIZE	(32 << 20) /* at least 32 meg */
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1

 /* SDRAM Bank Allocation method */
 #define SDRC_R_B_C		1

 /*--------------------------------------------------------------------------*/

 /*
  * NOR FLASH usage ... default nCS0:
  *  - one 256KB sector for U-Boot
  *  - one 256KB sector for its parameters (not all used)
  *  - eight sectors (2 MB) for kernel
  *  - rest for JFFS2
  */

 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)

 #define CONFIG_SYS_JFFS2_FIRST_BANK	CONFIG_SYS_MAX_FLASH_BANKS
 #define CONFIG_SYS_JFFS2_NUM_BANKS	1

 /*
  * NAND FLASH usage ... default nCS1:
  *  - four 128KB sectors for X-Loader
  *  - four 128KB sectors for U-Boot
  *  - two 128KB sector for its parameters
  *  - 32 sectors (4 MB) for kernel
  *  - rest for filesystem
  */

 /*
  * OneNAND FLASH usage ... default nCS2:
  *  - four 128KB sectors for X-Loader
  *  - two 128KB sectors for U-Boot
  *  - one 128KB sector for its parameters
  *  - sixteen sectors (2 MB) for kernel
  *  - rest for filesystem
  */

 /*--------------------------------------------------------------------------*/

 #ifndef __ASSEMBLY__
 extern unsigned int boot_flash_base;
 extern volatile unsigned int boot_flash_env_addr;
 extern unsigned int boot_flash_off;
 extern unsigned int boot_flash_sec;
 extern unsigned int boot_flash_type;
 #endif

 #endif				/* __CONFIG_H */
	/*
	* (C) Copyright 2006-2009
	* Texas Instruments Incorporated.
	* Richard Woodruff <r-woodruff2@ti.com>
	* Syed Mohammed Khasim <x0khasim@ti.com>
	* Nishanth Menon <nm@ti.com>
	*
	* Configuration settings for the 3430 TI SDP3430 board.
	*
	* See file CREDITS for list of people who contributed to this
	* project.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	* MA 02111-1307 USA
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/* TODO: REMOVE THE FOLLOWING
	* Retained the following till size.h is removed in u-boot
	*/
	#include <asm/sizes.h>
	/*
	* High Level Configuration Options
	*/
	#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
	#define CONFIG_OMAP 1 /* in a TI OMAP core */
	#define CONFIG_OMAP34XX 1 /* which is a 34XX */
	#define CONFIG_OMAP3430 1 /* which is in a 3430 */
	#define CONFIG_OMAP3_3430SDP 1 /* working with SDP Rev2 */

	#include <asm/arch/cpu.h> /* get chip and board defs */
	#include <asm/arch/omap3.h>

	/*
	* NOTE: these #defines presume standard SDP jumper settings.
	* In particular:
	* - 26 MHz clock (not 19.2 or 38.4 MHz)
	* - Boot from 128MB NOR, not NAND or OneNAND
	*
	* At this writing, OMAP3 U-Boot support doesn't permit concurrent
	* support for all the flash types the board supports.
	*/
	#define CONFIG_DISPLAY_CPUINFO 1
	#define CONFIG_DISPLAY_BOARDINFO 1

	/* Clock Defines */
	#define V_OSCK 26000000 /* Clock output from T2 */
	#define V_SCLK (V_OSCK >> 1)

	#undef CONFIG_USE_IRQ /* no support for IRQs */
	#define CONFIG_MISC_INIT_R

	#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
	#define CONFIG_SETUP_MEMORY_TAGS 1
	#define CONFIG_INITRD_TAG 1
	#define CONFIG_REVISION_TAG 1

	/*
	* Size of malloc() pool
	* Total Size Environment - 256k
	* Malloc - add 256k
	*/
	#define CONFIG_ENV_SIZE (256 << 10)
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (256 << 10))
	#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
	/* initial data */

	/--------------------------------------------------------------------------/

	/*
	* Hardware drivers
	*/

	/*
	* TWL4030
	*/
	#define CONFIG_TWL4030_POWER 1

	/*
	* serial port - NS16550 compatible
	*/
	#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */

	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE (-4)
	#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK

	/* Original SDP u-boot used UART1 and thus J8 (innermost); that can be
	* swapped with UART2 via jumpering. Downsides of using J8: it doesn't
	* support UART boot (that's only for UART3); it prevents sharing a Linux
	* kernel (LL_DEBUG_UART3) or filesystem (getty ttyS2) with most boards.
	*
	* UART boot uses UART3 on J9, and the SDP user's guide says to use
	* that for console. Downsides of using J9: you can't use IRDA too;
	* since UART3 isn't in the CORE power domain, it may be a bit less
	* usable in certain PM-sensitive debug scenarios.
	*/
	#undef CONSOLE_J9 /* else J8/UART1 (innermost) */

	#ifdef CONSOLE_J9
	#define CONFIG_CONS_INDEX 3
	#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
	#define CONFIG_SERIAL3 3 /* UART3 */
	#else
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
	#define CONFIG_SERIAL1 1 /* UART1 */
	#endif

	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_BAUDRATE 115200
	#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
	115200}

	/*
	* I2C for power management setup
	*/
	#define CONFIG_HARD_I2C 1
	#define CONFIG_SYS_I2C_SPEED 100000
	#define CONFIG_SYS_I2C_SLAVE 1
	#define CONFIG_SYS_I2C_BUS 0
	#define CONFIG_SYS_I2C_BUS_SELECT 1
	#define CONFIG_DRIVER_OMAP34XX_I2C 1

	/* DDR - I use Infineon DDR */
	#define CONFIG_OMAP3_INFINEON_DDR 1

	/* OMITTED: single 1 Gbit MT29F1G NAND flash */

	/*
	* NOR boot support - single 1 Gbit PF48F6000M0 Strataflash
	*/
	#define CONFIG_SYS_FLASH_BASE 0x10000000
	#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
	#define CONFIG_SYS_FLASH_CFI 1 /* use CFI geometry data */
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* ~10x faster writes */
	#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware sector protection */
	#define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* flinfo 'E' for empty */
	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */

	#define CONFIG_SYS_FLASH_CFI_WIDTH 2
	#define PHYS_FLASH_SIZE (128 << 20)
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors on one chip */

	/* timeout values are in milliseconds */
	#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
	#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)

	/* OMITTED: single 2 Gbit KFM2G16 OneNAND flash */

	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_SYS_ENV_SECT_SIZE (256 << 10)
	#define CONFIG_ENV_OFFSET CONFIG_SYS_ENV_SECT_SIZE
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_ENV_SECT_SIZE)
	/--------------------------------------------------------------------------/

	/* commands to include */
	#include <config_cmd_default.h>

	/* Enabled commands */
	#define CONFIG_CMD_DHCP /* DHCP Support */
	#define CONFIG_CMD_EXT2 /* EXT2 Support */
	#define CONFIG_CMD_FAT /* FAT support */
	#define CONFIG_CMD_I2C /* I2C serial bus support */
	#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
	#define CONFIG_CMD_MMC /* MMC support */
	#define CONFIG_CMD_NET

	/* Disabled commands */
	#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
	#undef CONFIG_CMD_IMLS /* List all found images */

	/--------------------------------------------------------------------------/
	/*
	* MMC boot support
	*/

	#if defined(CONFIG_CMD_MMC)
	#define CONFIG_MMC 1
	#define CONFIG_OMAP3_MMC 1
	#define CONFIG_DOS_PARTITION 1
	#endif

	/*----------------------------------------------------------------------------
	* SMSC9115 Ethernet from SMSC9118 family
	*----------------------------------------------------------------------------
	*/
	#if defined(CONFIG_CMD_NET)

	#define CONFIG_NET_MULTI
	#define CONFIG_LAN91C96
	#define CONFIG_LAN91C96_BASE DEBUG_BASE
	#define CONFIG_LAN91C96_EXT_PHY

	#define CONFIG_BOOTP_SEND_HOSTNAME
	/*
	* BOOTP fields
	*/
	#define CONFIG_BOOTP_SUBNETMASK 0x00000001
	#define CONFIG_BOOTP_GATEWAY 0x00000002
	#define CONFIG_BOOTP_HOSTNAME 0x00000004
	#define CONFIG_BOOTP_BOOTPATH 0x00000010
	#endif /* (CONFIG_CMD_NET) */

	/*
	* Environment setup
	*
	* Default boot order: mmc bootscript, MMC uImage, NOR image.
	* Network booting environment must be configured at site.
	*/

	/* allow overwriting serial config and ethaddr */
	#define CONFIG_ENV_OVERWRITE

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"loadaddr=0x82000000\0" \
	"console=ttyS0,115200n8\0" \
	"mmcargs=setenv bootargs console=${console} " \
	"root=/dev/mmcblk0p2 rw " \
	"rootfstype=ext3 rootwait\0" \
	"norargs=setenv bootargs console=${console} " \
	"root=/dev/mtdblock3 rw " \
	"rootfstype=jffs2\0" \
	"loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
	"bootscript=echo Running bootscript from MMC/SD ...; " \
	"autoscr ${loadaddr}\0" \
	"loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
	"mmcboot=echo Booting from MMC/SD ...; " \
	"run mmcargs; " \
	"bootm ${loadaddr}\0" \
	"norboot=echo Booting from NOR ...; " \
	"run norargs; " \
	"bootm 0x80000\0" \

	#define CONFIG_BOOTCOMMAND \
	"if mmcinit; then " \
	"if run loadbootscript; then " \
	"run bootscript; " \
	"else " \
	"if run loaduimage; then " \
	"run mmcboot; " \
	"else run norboot; " \
	"fi; " \
	"fi; " \
	"else run norboot; fi"

	#define CONFIG_AUTO_COMPLETE 1

	/--------------------------------------------------------------------------/

	/*
	* Miscellaneous configurable options
	*/

	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
	#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
	#define CONFIG_SYS_PROMPT "OMAP34XX SDP # "
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)

	/* SDRAM Test range - start at 16 meg boundary -ends at 32Meg -
	* a basic sanity check ONLY
	* IF you would like to increase coverage, increase the end address
	* or run the test with custom options
	*/
	#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x01000000)
	#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + (32 << 20))

	/* Default load address */
	#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0)

	/--------------------------------------------------------------------------/

	/*
	* 3430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
	* 32KHz clk, or from external sig. This rate is divided by a local divisor.
	*/
	#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
	#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
	#define CONFIG_SYS_HZ 1000

	/*
	* Stack sizes
	*
	* The stack sizes are set up in start.S using the settings below
	*/
	#define CONFIG_STACKSIZE (128 << 10) /* Regular stack */
	#ifdef CONFIG_USE_IRQ
	#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack */
	#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack */
	#endif

	/*
	* SDRAM Memory Map
	*/
	#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
	#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
	#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 meg */
	#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1

	/* SDRAM Bank Allocation method */
	#define SDRC_R_B_C 1

	/--------------------------------------------------------------------------/

	/*
	* NOR FLASH usage ... default nCS0:
	* - one 256KB sector for U-Boot
	* - one 256KB sector for its parameters (not all used)
	* - eight sectors (2 MB) for kernel
	* - rest for JFFS2
	*/

	/* Monitor at start of flash */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_MONITOR_LEN (256 << 10)

	#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
	#define CONFIG_SYS_JFFS2_NUM_BANKS 1

	/*
	* NAND FLASH usage ... default nCS1:
	* - four 128KB sectors for X-Loader
	* - four 128KB sectors for U-Boot
	* - two 128KB sector for its parameters
	* - 32 sectors (4 MB) for kernel
	* - rest for filesystem
	*/

	/*
	* OneNAND FLASH usage ... default nCS2:
	* - four 128KB sectors for X-Loader
	* - two 128KB sectors for U-Boot
	* - one 128KB sector for its parameters
	* - sixteen sectors (2 MB) for kernel
	* - rest for filesystem
	*/

	/--------------------------------------------------------------------------/

	#ifndef __ASSEMBLY__
	extern unsigned int boot_flash_base;
	extern volatile unsigned int boot_flash_env_addr;
	extern unsigned int boot_flash_off;
	extern unsigned int boot_flash_sec;
	extern unsigned int boot_flash_type;
	#endif

	#endif /* __CONFIG_H */