include/configs/mccmon6.h - github/trini/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright (C) 2016-2017
  * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #include "mx6_common.h"

 #define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + 0x80000)

 /*
  * Below defines are set but NOT really used since we by
  * design force U-Boot run when we boot in development
  * mode from SD card (SD2)
  */

 #define CONFIG_MXC_UART_BASE		UART1_BASE

 /* MMC Configuration */
 #define CFG_SYS_FSL_USDHC_NUM	2
 #define CFG_SYS_FSL_ESDHC_ADDR	0

 /* NOR 16-bit mode */
 #define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
 #define CONFIG_FLASH_VERIFY

 /* NOR Flash MTD */
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ (CONFIG_SYS_FLASH_BASE) }
 #define CONFIG_SYS_FLASH_BANKS_SIZES	{ (32 * SZ_1M) }

 /* Ethernet Configuration */
 #define CONFIG_FEC_MXC_PHYADDR		1

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"console=ttymxc0,115200 quiet\0" \
 	"fdt_high=0xffffffff\0" \
 	"initrd_high=0xffffffff\0" \
 	"boot_os=yes\0" \
 	"kernelsize=0x300000\0" \
 	"disable_giga=yes\0" \
 	"download_kernel=" \
 		"tftpboot ${loadaddr} ${kernel_file};\0" \
 	"get_boot_medium=" \
 		"setenv boot_medium nor;" \
 		"setexpr.l _src_sbmr1 *0x020d8004;" \
 		"setexpr _b_medium ${_src_sbmr1} '&' 0x00000040;" \
 		"if test ${_b_medium} = 40; then " \
 			"setenv boot_medium sdcard;" \
 		"fi\0" \
 	"kernel_file=fitImage\0" \
 	"boot_sd=" \
 		"echo '#######################';" \
 		"echo '# Factory SDcard Boot #';" \
 		"echo '#######################';" \
 		"setenv mmcdev 1;" \
 		"setenv mmcfactorydev 0;" \
 		"setenv mmcfactorypart 1;" \
 		"run factory_flash_img;\0" \
 	"boot_nor=" \
 		"setenv kernelnor 0x08180000;" \
 		"setenv bootargs console=${console} " \
 		CONFIG_MTDPARTS_DEFAULT " " \
 		"root=/dev/mmcblk1 rootfstype=ext4 rw rootwait noinitrd;" \
 		"cp.l ${kernelnor} ${loadaddr} ${kernelsize};" \
 		"bootm ${loadaddr};reset;\0" \
 	"boot_recovery=" \
 		"echo '#######################';" \
 		"echo '# RECOVERY SWU Boot   #';" \
 		"echo '#######################';" \
 		"setenv rootfsloadaddr 0x13000000;" \
 		"setenv swukernelnor 0x08980000;" \
 		"setenv swurootfsnor 0x09180000;" \
 		"setenv bootargs console=${console} " \
 		CONFIG_MTDPARTS_DEFAULT " " \
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
 		    ":${hostname}::off root=/dev/ram rw;" \
 		"cp.l ${swurootfsnor} ${rootfsloadaddr} 0x200000;" \
 		"cp.l ${swukernelnor} ${loadaddr} ${kernelsize};" \
 		"bootm ${loadaddr} ${rootfsloadaddr};reset;\0" \
 	"boot_tftp=" \
 		"echo '#######################';" \
 		"echo '# TFTP Boot           #';" \
 		"echo '#######################';" \
 		"if run download_kernel; then " \
 		     "setenv bootargs console=${console} " \
 		     "root=/dev/mmcblk0p2 rootwait;" \
 		     "bootm $loadaddr};reset;" \
 		"fi\0" \
 	"bootcmd=" \
 		"if test -n ${recovery_status}; then " \
 		     "run boot_recovery;" \
 		"else " \
 		     "if test ! -n ${boot_medium}; then " \
 			  "run get_boot_medium;" \
 			  "if test ${boot_medium} = sdcard; then " \
 			      "run boot_sd;" \
 			  "else " \
 			      "run boot_nor;" \
 			  "fi;" \
 		     "else " \
 			  "if test ${boot_medium} = tftp; then " \
 			      "run boot_tftp;" \
 			  "fi;" \
 		     "fi;" \
 		"fi\0" \
 	"bootdev=1\0" \
 	"bootpart=1\0" \
 	"netdev=eth0\0" \
 	"load_addr=0x11000000\0" \
 	"uboot_file=u-boot.img\0" \
 	"SPL_file=SPL\0" \
 	"load_uboot=tftp ${load_addr} ${uboot_file}\0" \
 	"nor_img_addr=0x11000000\0" \
 	"nor_img_file=core-image-lwn-mccmon6.nor\0" \
 	"emmc_img_file=core-image-lwn-mccmon6.ext4\0" \
 	"nor_bank_start=" __stringify(CONFIG_SYS_FLASH_BASE) "\0" \
 	"nor_img_size=0x02000000\0" \
 	"factory_script_file=factory.scr\0" \
 	"factory_load_script=" \
 		"if test -e mmc ${mmcdev}:${mmcfactorypart} " \
 		    "${factory_script_file}; then " \
 		    "load mmc ${mmcdev}:${mmcfactorypart} " \
 		     "${loadaddr} ${factory_script_file};" \
 		"fi\0" \
 	"factory_script=echo Running factory script from mmc${mmcdev} ...; " \
 		"source ${loadaddr}\0" \
 	"factory_flash_img="\
 		"echo 'Flash mccmon6 with factory images'; " \
 		"if run factory_load_script; then " \
 			"run factory_script;" \
 		"else " \
 		    "echo No factory script: ${factory_script_file} found on " \
 		    "device ${mmcdev};" \
 		    "run factory_nor_img;" \
 		    "run factory_eMMC_img;" \
 		    "run factory_SPL_falcon_setup;" \
 		"fi\0" \
 	"factory_eMMC_img="\
 		"echo 'Update mccmon6 eMMC image'; " \
 		"if load mmc ${mmcdev}:${mmcfactorypart} " \
 		    "${loadaddr} ${emmc_img_file}; then " \
 		    "setexpr fw_sz ${filesize} / 0x200;" \
 		    "setexpr fw_sz ${fw_sz} + 1;" \
 		    "mmc dev ${mmcfactorydev};" \
 		    "mmc write ${loadaddr} 0x0 ${fw_sz};" \
 		"fi\0" \
 	"factory_nor_img="\
 		"echo 'Update mccmon6 NOR image'; " \
 		"if load mmc ${mmcdev}:${mmcfactorypart} " \
 		    "${nor_img_addr} ${nor_img_file}; then " \
 			"run nor_update;" \
 		"fi\0" \
 	"nor_update=" \
 		    "protect off ${nor_bank_start} +${nor_img_size};" \
 		    "erase ${nor_bank_start} +${nor_img_size};" \
 		    "setexpr nor_img_size ${nor_img_size} / 4; " \
 		    "cp.l ${nor_img_addr} ${nor_bank_start} ${nor_img_size}\0" \
 	"factory_SPL_falcon_setup="\
 		"echo 'Write Falcon boot data'; " \
 		"setenv kernelnor 0x08180000;" \
 		"cp.l ${kernelnor} ${loadaddr} ${kernelsize};" \
 		"spl export fdt ${loadaddr};" \
 		"setenv nor_img_addr ${fdtargsaddr};" \
 		"setenv nor_img_size 0x20000;" \
 		"setenv nor_bank_start " \
 				__stringify(CONFIG_CMD_SPL_NOR_OFS)";" \
 		"run nor_update\0" \
 	"tftp_nor_uboot="\
 		"echo 'Update mccmon6 NOR U-BOOT via TFTP'; " \
 		"setenv nor_img_file u-boot.img; " \
 		"setenv nor_img_size 0x80000; " \
 		"setenv nor_bank_start 0x08080000; " \
 		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
 		    "run nor_update;" \
 		"fi\0" \
 	"tftp_nor_fitImg="\
 		"echo 'Update mccmon6 NOR fitImage via TFTP'; " \
 		"setenv nor_img_file fitImage; " \
 		"setenv nor_img_size 0x500000; " \
 		"setenv nor_bank_start 0x08180000; " \
 		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
 		    "run nor_update;" \
 		"fi\0" \
 	"tftp_nor_img="\
 		"echo 'Update mccmon6 NOR image via TFTP'; " \
 		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
 		    "run nor_update;" \
 		"fi\0" \
 	"tftp_nor_SPL="\
 		"if tftp ${load_addr} SPL_padded; then " \
 		    "erase 0x08000000 +0x20000;" \
 		    "cp.b ${load_addr} 0x08000000 0x20000;" \
 		"fi;\0" \
 	"tftp_sd_SPL="\
 	    "if mmc dev 1; then "      \
 		"if tftp ${load_addr} ${SPL_file}; then " \
 		    "setexpr fw_sz ${filesize} / 0x200; " \
 		    "setexpr fw_sz ${fw_sz} + 1; " \
 		    "mmc write ${load_addr} 0x2 ${fw_sz};" \
 		"fi;" \
 	    "fi;\0" \
 	"tftp_sd_uboot="\
 	    "if mmc dev 1; then "      \
 		"if run load_uboot; then " \
 		    "setexpr fw_sz ${filesize} / 0x200; " \
 		    "setexpr fw_sz ${fw_sz} + 1; " \
 		    "mmc write ${load_addr} 0x8A ${fw_sz};" \
 		"fi;" \
 	    "fi;\0"

 /* Physical Memory Map */
 #define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

 #define CFG_SYS_SDRAM_BASE		PHYS_SDRAM
 #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

 /* Environment organization */

 /* Envs are stored in NOR flash */

 #endif			       /* __CONFIG_H * */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright (C) 2016-2017
	* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#include "mx6_common.h"

	#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + 0x80000)

	/*
	* Below defines are set but NOT really used since we by
	* design force U-Boot run when we boot in development
	* mode from SD card (SD2)
	*/

	#define CONFIG_MXC_UART_BASE UART1_BASE

	/* MMC Configuration */
	#define CFG_SYS_FSL_USDHC_NUM 2
	#define CFG_SYS_FSL_ESDHC_ADDR 0

	/* NOR 16-bit mode */
	#define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR
	#define CONFIG_FLASH_VERIFY

	/* NOR Flash MTD */
	#define CONFIG_SYS_FLASH_BANKS_LIST { (CONFIG_SYS_FLASH_BASE) }
	#define CONFIG_SYS_FLASH_BANKS_SIZES { (32 * SZ_1M) }

	/* Ethernet Configuration */
	#define CONFIG_FEC_MXC_PHYADDR 1

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"console=ttymxc0,115200 quiet\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"boot_os=yes\0" \
	"kernelsize=0x300000\0" \
	"disable_giga=yes\0" \
	"download_kernel=" \
	"tftpboot ${loadaddr} ${kernel_file};\0" \
	"get_boot_medium=" \
	"setenv boot_medium nor;" \
	"setexpr.l _src_sbmr1 *0x020d8004;" \
	"setexpr _b_medium ${_src_sbmr1} '&' 0x00000040;" \
	"if test ${_b_medium} = 40; then " \
	"setenv boot_medium sdcard;" \
	"fi\0" \
	"kernel_file=fitImage\0" \
	"boot_sd=" \
	"echo '#######################';" \
	"echo '# Factory SDcard Boot #';" \
	"echo '#######################';" \
	"setenv mmcdev 1;" \
	"setenv mmcfactorydev 0;" \
	"setenv mmcfactorypart 1;" \
	"run factory_flash_img;\0" \
	"boot_nor=" \
	"setenv kernelnor 0x08180000;" \
	"setenv bootargs console=${console} " \
	CONFIG_MTDPARTS_DEFAULT " " \
	"root=/dev/mmcblk1 rootfstype=ext4 rw rootwait noinitrd;" \
	"cp.l ${kernelnor} ${loadaddr} ${kernelsize};" \
	"bootm ${loadaddr};reset;\0" \
	"boot_recovery=" \
	"echo '#######################';" \
	"echo '# RECOVERY SWU Boot #';" \
	"echo '#######################';" \
	"setenv rootfsloadaddr 0x13000000;" \
	"setenv swukernelnor 0x08980000;" \
	"setenv swurootfsnor 0x09180000;" \
	"setenv bootargs console=${console} " \
	CONFIG_MTDPARTS_DEFAULT " " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}::off root=/dev/ram rw;" \
	"cp.l ${swurootfsnor} ${rootfsloadaddr} 0x200000;" \
	"cp.l ${swukernelnor} ${loadaddr} ${kernelsize};" \
	"bootm ${loadaddr} ${rootfsloadaddr};reset;\0" \
	"boot_tftp=" \
	"echo '#######################';" \
	"echo '# TFTP Boot #';" \
	"echo '#######################';" \
	"if run download_kernel; then " \
	"setenv bootargs console=${console} " \
	"root=/dev/mmcblk0p2 rootwait;" \
	"bootm $loadaddr};reset;" \
	"fi\0" \
	"bootcmd=" \
	"if test -n ${recovery_status}; then " \
	"run boot_recovery;" \
	"else " \
	"if test ! -n ${boot_medium}; then " \
	"run get_boot_medium;" \
	"if test ${boot_medium} = sdcard; then " \
	"run boot_sd;" \
	"else " \
	"run boot_nor;" \
	"fi;" \
	"else " \
	"if test ${boot_medium} = tftp; then " \
	"run boot_tftp;" \
	"fi;" \
	"fi;" \
	"fi\0" \
	"bootdev=1\0" \
	"bootpart=1\0" \
	"netdev=eth0\0" \
	"load_addr=0x11000000\0" \
	"uboot_file=u-boot.img\0" \
	"SPL_file=SPL\0" \
	"load_uboot=tftp ${load_addr} ${uboot_file}\0" \
	"nor_img_addr=0x11000000\0" \
	"nor_img_file=core-image-lwn-mccmon6.nor\0" \
	"emmc_img_file=core-image-lwn-mccmon6.ext4\0" \
	"nor_bank_start=" __stringify(CONFIG_SYS_FLASH_BASE) "\0" \
	"nor_img_size=0x02000000\0" \
	"factory_script_file=factory.scr\0" \
	"factory_load_script=" \
	"if test -e mmc ${mmcdev}:${mmcfactorypart} " \
	"${factory_script_file}; then " \
	"load mmc ${mmcdev}:${mmcfactorypart} " \
	"${loadaddr} ${factory_script_file};" \
	"fi\0" \
	"factory_script=echo Running factory script from mmc${mmcdev} ...; " \
	"source ${loadaddr}\0" \
	"factory_flash_img="\
	"echo 'Flash mccmon6 with factory images'; " \
	"if run factory_load_script; then " \
	"run factory_script;" \
	"else " \
	"echo No factory script: ${factory_script_file} found on " \
	"device ${mmcdev};" \
	"run factory_nor_img;" \
	"run factory_eMMC_img;" \
	"run factory_SPL_falcon_setup;" \
	"fi\0" \
	"factory_eMMC_img="\
	"echo 'Update mccmon6 eMMC image'; " \
	"if load mmc ${mmcdev}:${mmcfactorypart} " \
	"${loadaddr} ${emmc_img_file}; then " \
	"setexpr fw_sz ${filesize} / 0x200;" \
	"setexpr fw_sz ${fw_sz} + 1;" \
	"mmc dev ${mmcfactorydev};" \
	"mmc write ${loadaddr} 0x0 ${fw_sz};" \
	"fi\0" \
	"factory_nor_img="\
	"echo 'Update mccmon6 NOR image'; " \
	"if load mmc ${mmcdev}:${mmcfactorypart} " \
	"${nor_img_addr} ${nor_img_file}; then " \
	"run nor_update;" \
	"fi\0" \
	"nor_update=" \
	"protect off ${nor_bank_start} +${nor_img_size};" \
	"erase ${nor_bank_start} +${nor_img_size};" \
	"setexpr nor_img_size ${nor_img_size} / 4; " \
	"cp.l ${nor_img_addr} ${nor_bank_start} ${nor_img_size}\0" \
	"factory_SPL_falcon_setup="\
	"echo 'Write Falcon boot data'; " \
	"setenv kernelnor 0x08180000;" \
	"cp.l ${kernelnor} ${loadaddr} ${kernelsize};" \
	"spl export fdt ${loadaddr};" \
	"setenv nor_img_addr ${fdtargsaddr};" \
	"setenv nor_img_size 0x20000;" \
	"setenv nor_bank_start " \
	__stringify(CONFIG_CMD_SPL_NOR_OFS)";" \
	"run nor_update\0" \
	"tftp_nor_uboot="\
	"echo 'Update mccmon6 NOR U-BOOT via TFTP'; " \
	"setenv nor_img_file u-boot.img; " \
	"setenv nor_img_size 0x80000; " \
	"setenv nor_bank_start 0x08080000; " \
	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
	"run nor_update;" \
	"fi\0" \
	"tftp_nor_fitImg="\
	"echo 'Update mccmon6 NOR fitImage via TFTP'; " \
	"setenv nor_img_file fitImage; " \
	"setenv nor_img_size 0x500000; " \
	"setenv nor_bank_start 0x08180000; " \
	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
	"run nor_update;" \
	"fi\0" \
	"tftp_nor_img="\
	"echo 'Update mccmon6 NOR image via TFTP'; " \
	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
	"run nor_update;" \
	"fi\0" \
	"tftp_nor_SPL="\
	"if tftp ${load_addr} SPL_padded; then " \
	"erase 0x08000000 +0x20000;" \
	"cp.b ${load_addr} 0x08000000 0x20000;" \
	"fi;\0" \
	"tftp_sd_SPL="\
	"if mmc dev 1; then " \
	"if tftp ${load_addr} ${SPL_file}; then " \
	"setexpr fw_sz ${filesize} / 0x200; " \
	"setexpr fw_sz ${fw_sz} + 1; " \
	"mmc write ${load_addr} 0x2 ${fw_sz};" \
	"fi;" \
	"fi;\0" \
	"tftp_sd_uboot="\
	"if mmc dev 1; then " \
	"if run load_uboot; then " \
	"setexpr fw_sz ${filesize} / 0x200; " \
	"setexpr fw_sz ${fw_sz} + 1; " \
	"mmc write ${load_addr} 0x8A ${fw_sz};" \
	"fi;" \
	"fi;\0"

	/* Physical Memory Map */
	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR

	#define CFG_SYS_SDRAM_BASE PHYS_SDRAM
	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE

	/* Environment organization */

	/* Envs are stored in NOR flash */

	#endif /* __CONFIG_H * */