blob: 281c3a1d6632b2e4b97b9feed9038107ca4c1610 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Driver for AT91/AT32 LCD Controller
*
* Copyright (C) 2007 Atmel Corporation
*/
#include <atmel_lcd.h>
#include <dm.h>
#include <fdtdec.h>
#include <log.h>
#include <part.h>
#include <video.h>
#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <bmp_layout.h>
#include <atmel_lcdc.h>
#include <linux/delay.h>
DECLARE_GLOBAL_DATA_PTR;
enum {
/* Maximum LCD size we support */
LCD_MAX_WIDTH = 1366,
LCD_MAX_HEIGHT = 768,
LCD_MAX_LOG2_BPP = VIDEO_BPP16,
};
struct atmel_fb_priv {
struct display_timing timing;
};
/* configurable parameters */
#define ATMEL_LCDC_CVAL_DEFAULT 0xc8
#define ATMEL_LCDC_DMA_BURST_LEN 8
#ifndef ATMEL_LCDC_GUARD_TIME
#define ATMEL_LCDC_GUARD_TIME 1
#endif
#if defined(CONFIG_AT91SAM9263)
#define ATMEL_LCDC_FIFO_SIZE 2048
#else
#define ATMEL_LCDC_FIFO_SIZE 512
#endif
#define lcdc_readl(mmio, reg) __raw_readl((mmio)+(reg))
#define lcdc_writel(mmio, reg, val) __raw_writel((val), (mmio)+(reg))
static void atmel_fb_init(ulong addr, struct display_timing *timing, int bpix,
bool tft, bool cont_pol_low, ulong lcdbase)
{
unsigned long value;
void *reg = (void *)addr;
/* Turn off the LCD controller and the DMA controller */
lcdc_writel(reg, ATMEL_LCDC_PWRCON,
ATMEL_LCDC_GUARD_TIME << ATMEL_LCDC_GUARDT_OFFSET);
/* Wait for the LCDC core to become idle */
while (lcdc_readl(reg, ATMEL_LCDC_PWRCON) & ATMEL_LCDC_BUSY)
udelay(10);
lcdc_writel(reg, ATMEL_LCDC_DMACON, 0);
/* Reset LCDC DMA */
lcdc_writel(reg, ATMEL_LCDC_DMACON, ATMEL_LCDC_DMARST);
/* ...set frame size and burst length = 8 words (?) */
value = (timing->hactive.typ * timing->vactive.typ *
(1 << bpix)) / 32;
value |= ((ATMEL_LCDC_DMA_BURST_LEN - 1) << ATMEL_LCDC_BLENGTH_OFFSET);
lcdc_writel(reg, ATMEL_LCDC_DMAFRMCFG, value);
/* Set pixel clock */
value = get_lcdc_clk_rate(0) / timing->pixelclock.typ;
if (get_lcdc_clk_rate(0) % timing->pixelclock.typ)
value++;
value = (value / 2) - 1;
if (!value) {
lcdc_writel(reg, ATMEL_LCDC_LCDCON1, ATMEL_LCDC_BYPASS);
} else
lcdc_writel(reg, ATMEL_LCDC_LCDCON1,
value << ATMEL_LCDC_CLKVAL_OFFSET);
/* Initialize control register 2 */
value = ATMEL_LCDC_MEMOR_LITTLE | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE;
if (tft)
value |= ATMEL_LCDC_DISTYPE_TFT;
if (!(timing->flags & DISPLAY_FLAGS_HSYNC_HIGH))
value |= ATMEL_LCDC_INVLINE_INVERTED;
if (!(timing->flags & DISPLAY_FLAGS_VSYNC_HIGH))
value |= ATMEL_LCDC_INVFRAME_INVERTED;
value |= bpix << 5;
lcdc_writel(reg, ATMEL_LCDC_LCDCON2, value);
/* Vertical timing */
value = (timing->vsync_len.typ - 1) << ATMEL_LCDC_VPW_OFFSET;
value |= timing->vback_porch.typ << ATMEL_LCDC_VBP_OFFSET;
value |= timing->vfront_porch.typ;
/* Magic! (Datasheet says "Bit 31 must be written to 1") */
value |= 1U << 31;
lcdc_writel(reg, ATMEL_LCDC_TIM1, value);
/* Horizontal timing */
value = (timing->hfront_porch.typ - 1) << ATMEL_LCDC_HFP_OFFSET;
value |= (timing->hsync_len.typ - 1) << ATMEL_LCDC_HPW_OFFSET;
value |= (timing->hback_porch.typ - 1);
lcdc_writel(reg, ATMEL_LCDC_TIM2, value);
/* Display size */
value = (timing->hactive.typ - 1) << ATMEL_LCDC_HOZVAL_OFFSET;
value |= timing->vactive.typ - 1;
lcdc_writel(reg, ATMEL_LCDC_LCDFRMCFG, value);
/* FIFO Threshold: Use formula from data sheet */
value = ATMEL_LCDC_FIFO_SIZE - (2 * ATMEL_LCDC_DMA_BURST_LEN + 3);
lcdc_writel(reg, ATMEL_LCDC_FIFO, value);
/* Toggle LCD_MODE every frame */
lcdc_writel(reg, ATMEL_LCDC_MVAL, 0);
/* Disable all interrupts */
lcdc_writel(reg, ATMEL_LCDC_IDR, ~0UL);
/* Set contrast */
value = ATMEL_LCDC_PS_DIV8 |
ATMEL_LCDC_ENA_PWMENABLE;
if (!cont_pol_low)
value |= ATMEL_LCDC_POL_POSITIVE;
lcdc_writel(reg, ATMEL_LCDC_CONTRAST_CTR, value);
lcdc_writel(reg, ATMEL_LCDC_CONTRAST_VAL, ATMEL_LCDC_CVAL_DEFAULT);
/* Set framebuffer DMA base address and pixel offset */
lcdc_writel(reg, ATMEL_LCDC_DMABADDR1, lcdbase);
lcdc_writel(reg, ATMEL_LCDC_DMACON, ATMEL_LCDC_DMAEN);
lcdc_writel(reg, ATMEL_LCDC_PWRCON,
(ATMEL_LCDC_GUARD_TIME << ATMEL_LCDC_GUARDT_OFFSET) | ATMEL_LCDC_PWR);
}
static int atmel_fb_lcd_probe(struct udevice *dev)
{
struct video_uc_plat *uc_plat = dev_get_uclass_plat(dev);
struct video_priv *uc_priv = dev_get_uclass_priv(dev);
struct atmel_fb_priv *priv = dev_get_priv(dev);
struct display_timing *timing = &priv->timing;
/*
* For now some values are hard-coded. We could use the device tree
* bindings in simple-framebuffer.txt to specify the format/bpp and
* some Atmel-specific binding for tft and cont_pol_low.
*/
atmel_fb_init(ATMEL_BASE_LCDC, timing, VIDEO_BPP16, true, false,
uc_plat->base);
uc_priv->xsize = timing->hactive.typ;
uc_priv->ysize = timing->vactive.typ;
uc_priv->bpix = VIDEO_BPP16;
video_set_flush_dcache(dev, true);
debug("LCD frame buffer at %lx, size %x, %dx%d pixels\n", uc_plat->base,
uc_plat->size, uc_priv->xsize, uc_priv->ysize);
return 0;
}
static int atmel_fb_of_to_plat(struct udevice *dev)
{
struct atmel_lcd_plat *plat = dev_get_plat(dev);
struct atmel_fb_priv *priv = dev_get_priv(dev);
struct display_timing *timing = &priv->timing;
const void *blob = gd->fdt_blob;
if (fdtdec_decode_display_timing(blob, dev_of_offset(dev),
plat->timing_index, timing)) {
debug("%s: Failed to decode display timing\n", __func__);
return -EINVAL;
}
return 0;
}
static int atmel_fb_lcd_bind(struct udevice *dev)
{
struct video_uc_plat *uc_plat = dev_get_uclass_plat(dev);
uc_plat->size = LCD_MAX_WIDTH * LCD_MAX_HEIGHT *
(1 << VIDEO_BPP16) / 8;
debug("%s: Frame buffer size %x\n", __func__, uc_plat->size);
return 0;
}
static const struct udevice_id atmel_fb_lcd_ids[] = {
{ .compatible = "atmel,at91sam9g45-lcdc" },
{ }
};
U_BOOT_DRIVER(atmel_fb) = {
.name = "atmel_fb",
.id = UCLASS_VIDEO,
.of_match = atmel_fb_lcd_ids,
.bind = atmel_fb_lcd_bind,
.of_to_plat = atmel_fb_of_to_plat,
.probe = atmel_fb_lcd_probe,
.plat_auto = sizeof(struct atmel_lcd_plat),
.priv_auto = sizeof(struct atmel_fb_priv),
};