| /* |
| * (C) Copyright 2001 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #include <common.h> |
| #include <ioports.h> |
| #include <mpc8260.h> |
| #include <linux/compiler.h> |
| |
| #include "scm.h" |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| static void config_scoh_cs(void); |
| extern int fpga_init(void); |
| |
| #if 0 |
| #define DEBUGF(fmt,args...) printf (fmt ,##args) |
| #else |
| #define DEBUGF(fmt,args...) |
| #endif |
| |
| /* |
| * I/O Port configuration table |
| * |
| * if conf is 1, then that port pin will be configured at boot time |
| * according to the five values podr/pdir/ppar/psor/pdat for that entry |
| */ |
| |
| const iop_conf_t iop_conf_tab[4][32] = { |
| |
| /* Port A configuration */ |
| { /* conf ppar psor pdir podr pdat */ |
| /* PA31 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII COL */ |
| /* PA30 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII CRS */ |
| /* PA29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_ER */ |
| /* PA28 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_EN */ |
| /* PA27 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_DV */ |
| /* PA26 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_ER */ |
| /* PA25 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PA24 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PA23 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PA22 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PA21 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[3] */ |
| /* PA20 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[2] */ |
| /* PA19 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[1] */ |
| /* PA18 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[0] */ |
| /* PA17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[0] */ |
| /* PA16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[1]*/ |
| /* PA15 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[2] */ |
| /* PA14 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[3] */ |
| /* PA13 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PA12 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PA11 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PA10 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PA9 */ { 1, 1, 1, 1, 0, 0 }, /* TDM_A1 L1TXD0 */ |
| /* PA8 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_A1 L1RXD0 */ |
| /* PA7 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_A1 L1TSYNC */ |
| /* PA6 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_A1 L1RSYNC */ |
| /* PA5 */ { 1, 0, 0, 0, 0, 0 }, /* FIOX_FPGA_PR */ |
| /* PA4 */ { 1, 0, 0, 0, 0, 0 }, /* DOHM_FPGA_PR */ |
| /* PA3 */ { 1, 1, 0, 0, 0, 0 }, /* TDM RXCLK4 */ |
| /* PA2 */ { 1, 1, 0, 0, 0, 0 }, /* TDM TXCLK4 */ |
| /* PA1 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PA0 */ { 1, 0, 0, 0, 0, 0 } /* BUSY */ |
| }, |
| |
| /* Port B configuration */ |
| { /* conf ppar psor pdir podr pdat */ |
| /* PB31 */ { 1, 0, 0, 1, 0, 0 }, /* EQ_ALARM_MIN */ |
| /* PB30 */ { 1, 0, 0, 1, 0, 0 }, /* EQ_ALARM_MAJ */ |
| /* PB29 */ { 1, 0, 0, 1, 0, 0 }, /* COM_ALARM_MIN */ |
| /* PB28 */ { 1, 0, 0, 1, 0, 0 }, /* COM_ALARM_MAJ */ |
| /* PB27 */ { 0, 1, 0, 0, 0, 0 }, |
| /* PB26 */ { 0, 1, 0, 0, 0, 0 }, |
| /* PB25 */ { 1, 0, 0, 1, 0, 0 }, /* LED_GREEN_L */ |
| /* PB24 */ { 1, 0, 0, 1, 0, 0 }, /* LED_RED_L */ |
| /* PB23 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_D2 L1TXD */ |
| /* PB22 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_D2 L1RXD */ |
| /* PB21 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_D2 L1TSYNC */ |
| /* PB20 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_D2 L1RSYNC */ |
| /* PB19 */ { 1, 0, 0, 0, 0, 0 }, /* UID */ |
| /* PB18 */ { 0, 1, 0, 0, 0, 0 }, |
| /* PB17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RX_DV */ |
| /* PB16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RX_ER */ |
| /* PB15 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TX_ER */ |
| /* PB14 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TX_EN */ |
| /* PB13 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII COL */ |
| /* PB12 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII CRS */ |
| /* PB11 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[3] */ |
| /* PB10 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[2] */ |
| /* PB9 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[1] */ |
| /* PB8 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RxD[0] */ |
| /* PB7 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[3] */ |
| /* PB6 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[2] */ |
| /* PB5 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[1] */ |
| /* PB4 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3 MII TxD[0] */ |
| /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ |
| /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ |
| /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ |
| /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ |
| }, |
| |
| /* Port C configuration */ |
| { /* conf ppar psor pdir podr pdat */ |
| /* PC31 */ { 1, 1, 0, 0, 0, 0 }, /* TDM RXCLK1 */ |
| /* PC30 */ { 1, 1, 0, 0, 0, 0 }, /* TDM TXCLK1 */ |
| /* PC29 */ { 1, 1, 0, 0, 0, 0 }, /* TDM RXCLK3 */ |
| /* PC28 */ { 1, 1, 0, 0, 0, 0 }, /* TDM TXCLK3 */ |
| /* PC27 */ { 1, 1, 0, 0, 0, 0 }, /* TDM RXCLK2 */ |
| /* PC26 */ { 1, 1, 0, 0, 0, 0 }, /* TDM TXCLK2 */ |
| /* PC25 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PC24 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PC23 */ { 0, 1, 0, 1, 0, 0 }, |
| /* PC22 */ { 0, 1, 0, 0, 0, 0 }, |
| /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII TX_CLK */ |
| /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RX_CLK */ |
| /* PC19 */ { 0, 1, 0, 0, 0, 0 }, |
| /* PC18 */ { 0, 1, 0, 0, 0, 0 }, |
| /* PC17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII RX_CLK */ |
| /* PC16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3 MII TX_CLK */ |
| /* PC15 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PC14 */ { 0, 1, 0, 0, 0, 0 }, |
| /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* RES_PHY_L */ |
| /* PC12 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PC11 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PC10 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PC9 */ { 0, 1, 1, 0, 0, 0 }, /* TDM_A2 L1TSYNC */ |
| /* PC8 */ { 0, 0, 0, 0, 0, 0 }, /* FEP_RDY */ |
| /* PC7 */ { 0, 0, 0, 0, 0, 0 }, |
| /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* UC4_ALARM_L */ |
| /* PC5 */ { 0, 0, 0, 0, 0, 0 }, /* UC3_ALARM_L */ |
| /* PC4 */ { 0, 0, 0, 0, 0, 0 }, /* UC2_ALARM_L */ |
| /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* RES_MISC_L */ |
| /* PC2 */ { 0, 0, 0, 1, 0, 0 }, /* RES_OH_L */ |
| /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* RES_DOHM_L */ |
| /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* RES_FIOX_L */ |
| }, |
| |
| /* Port D configuration */ |
| { /* conf ppar psor pdir podr pdat */ |
| /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ |
| /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ |
| /* PD29 */ { 0, 0, 0, 0, 0, 0 }, /* INIT_F */ |
| /* PD28 */ { 0, 0, 0, 1, 0, 0 }, /* DONE_F */ |
| /* PD27 */ { 0, 0, 0, 0, 0, 0 }, /* INIT_D */ |
| /* PD26 */ { 0, 0, 0, 1, 0, 0 }, /* DONE_D */ |
| /* PD25 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PD24 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PD23 */ { 0, 0, 0, 1, 0, 0 }, |
| /* PD22 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_A2 L1TXD */ |
| /* PD21 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_A2 L1RXD */ |
| /* PD20 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_A2 L1RSYNC */ |
| /* PD19 */ { 1, 1, 1, 0, 0, 0 }, /* SPI SPISEL */ |
| /* PD18 */ { 1, 1, 1, 0, 0, 0 }, /* SPI SPICLK */ |
| /* PD17 */ { 1, 1, 1, 0, 0, 0 }, /* SPI SPIMOSI */ |
| /* PD16 */ { 1, 1, 1, 0, 0, 0 }, /* SPI SPIMOSO */ |
| #if defined(CONFIG_SOFT_I2C) |
| /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ |
| /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ |
| #else |
| #if defined(CONFIG_HARD_I2C) |
| /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */ |
| /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */ |
| #else /* normal I/O port pins */ |
| /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */ |
| /* PD14 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SCL */ |
| #endif |
| #endif |
| /* PD13 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_B1 L1TXD */ |
| /* PD12 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_B1 L1RXD */ |
| /* PD11 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_B1 L1TSYNC */ |
| /* PD10 */ { 1, 1, 1, 0, 0, 0 }, /* TDM_B1 L1RSYNC */ |
| /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ |
| /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ |
| /* PD7 */ { 0, 0, 0, 1, 0, 1 }, |
| /* PD6 */ { 0, 0, 0, 1, 0, 1 }, |
| /* PD5 */ { 0, 0, 0, 1, 0, 0 }, /* PROG_F */ |
| /* PD4 */ { 0, 0, 0, 1, 0, 0 }, /* PROG_D */ |
| /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ |
| /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ |
| /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ |
| /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ |
| } |
| }; |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| /* Check Board Identity: |
| */ |
| int checkboard (void) |
| { |
| char str[64]; |
| int i = getenv_f("serial#", str, sizeof (str)); |
| |
| puts ("Board: "); |
| |
| if (!i || strncmp (str, "TQM8260", 7)) { |
| puts ("### No HW ID - assuming TQM8260\n"); |
| return (0); |
| } |
| |
| puts (str); |
| putc ('\n'); |
| |
| return 0; |
| } |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| /* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx |
| * |
| * This routine performs standard 8260 initialization sequence |
| * and calculates the available memory size. It may be called |
| * several times to try different SDRAM configurations on both |
| * 60x and local buses. |
| */ |
| static long int try_init (volatile memctl8260_t * memctl, ulong sdmr, |
| ulong orx, volatile uchar * base) |
| { |
| volatile uchar c = 0xff; |
| volatile uint *sdmr_ptr; |
| volatile uint *orx_ptr; |
| ulong maxsize, size; |
| int i; |
| |
| /* We must be able to test a location outsize the maximum legal size |
| * to find out THAT we are outside; but this address still has to be |
| * mapped by the controller. That means, that the initial mapping has |
| * to be (at least) twice as large as the maximum expected size. |
| */ |
| maxsize = (1 + (~orx | 0x7fff)) / 2; |
| |
| /* Since CONFIG_SYS_SDRAM_BASE is always 0 (??), we assume that |
| * we are configuring CS1 if base != 0 |
| */ |
| sdmr_ptr = base ? &memctl->memc_lsdmr : &memctl->memc_psdmr; |
| orx_ptr = base ? &memctl->memc_or2 : &memctl->memc_or1; |
| |
| *orx_ptr = orx; |
| |
| /* |
| * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35): |
| * |
| * "At system reset, initialization software must set up the |
| * programmable parameters in the memory controller banks registers |
| * (ORx, BRx, P/LSDMR). After all memory parameters are configured, |
| * system software should execute the following initialization sequence |
| * for each SDRAM device. |
| * |
| * 1. Issue a PRECHARGE-ALL-BANKS command |
| * 2. Issue eight CBR REFRESH commands |
| * 3. Issue a MODE-SET command to initialize the mode register |
| * |
| * The initial commands are executed by setting P/LSDMR[OP] and |
| * accessing the SDRAM with a single-byte transaction." |
| * |
| * The appropriate BRx/ORx registers have already been set when we |
| * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE. |
| */ |
| |
| *sdmr_ptr = sdmr | PSDMR_OP_PREA; |
| *base = c; |
| |
| *sdmr_ptr = sdmr | PSDMR_OP_CBRR; |
| for (i = 0; i < 8; i++) |
| *base = c; |
| |
| *sdmr_ptr = sdmr | PSDMR_OP_MRW; |
| *(base + CONFIG_SYS_MRS_OFFS) = c; /* setting MR on address lines */ |
| |
| *sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN; |
| *base = c; |
| |
| size = get_ram_size((long *)base, maxsize); |
| |
| *orx_ptr = orx | ~(size - 1); |
| |
| return (size); |
| } |
| |
| /* |
| * Test Power-On-Reset. |
| */ |
| int power_on_reset (void) |
| { |
| /* Test Reset Status Register */ |
| return gd->reset_status & RSR_CSRS ? 0 : 1; |
| } |
| |
| phys_size_t initdram (int board_type) |
| { |
| volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; |
| volatile memctl8260_t *memctl = &immap->im_memctl; |
| |
| #ifndef CONFIG_SYS_RAMBOOT |
| long size8, size9; |
| #endif |
| long psize, lsize; |
| |
| psize = 16 * 1024 * 1024; |
| lsize = 0; |
| |
| memctl->memc_psrt = CONFIG_SYS_PSRT; |
| memctl->memc_mptpr = CONFIG_SYS_MPTPR; |
| |
| #if 0 /* Just for debugging */ |
| #define prt_br_or(brX,orX) do { \ |
| ulong start = memctl->memc_ ## brX & 0xFFFF8000; \ |
| ulong sizem = ~memctl->memc_ ## orX | 0x00007FFF; \ |
| printf ("\n" \ |
| #brX " 0x%08x " #orX " 0x%08x " \ |
| "==> 0x%08lx ... 0x%08lx = %ld MB\n", \ |
| memctl->memc_ ## brX, memctl->memc_ ## orX, \ |
| start, start+sizem, (sizem+1)>>20); \ |
| } while (0) |
| prt_br_or (br0, or0); |
| prt_br_or (br1, or1); |
| prt_br_or (br2, or2); |
| prt_br_or (br3, or3); |
| #endif |
| |
| #ifndef CONFIG_SYS_RAMBOOT |
| /* 60x SDRAM setup: |
| */ |
| size8 = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR1_8COL, |
| (uchar *) CONFIG_SYS_SDRAM_BASE); |
| size9 = try_init (memctl, CONFIG_SYS_PSDMR_9COL, CONFIG_SYS_OR1_9COL, |
| (uchar *) CONFIG_SYS_SDRAM_BASE); |
| |
| if (size8 < size9) { |
| psize = size9; |
| printf ("(60x:9COL - %ld MB, ", psize >> 20); |
| } else { |
| psize = try_init (memctl, CONFIG_SYS_PSDMR_8COL, CONFIG_SYS_OR1_8COL, |
| (uchar *) CONFIG_SYS_SDRAM_BASE); |
| printf ("(60x:8COL - %ld MB, ", psize >> 20); |
| } |
| |
| /* Local SDRAM setup: |
| */ |
| #ifdef CONFIG_SYS_INIT_LOCAL_SDRAM |
| memctl->memc_lsrt = CONFIG_SYS_LSRT; |
| size8 = try_init (memctl, CONFIG_SYS_LSDMR_8COL, CONFIG_SYS_OR2_8COL, |
| (uchar *) SDRAM_BASE2_PRELIM); |
| size9 = try_init (memctl, CONFIG_SYS_LSDMR_9COL, CONFIG_SYS_OR2_9COL, |
| (uchar *) SDRAM_BASE2_PRELIM); |
| |
| if (size8 < size9) { |
| lsize = size9; |
| printf ("Local:9COL - %ld MB) using ", lsize >> 20); |
| } else { |
| lsize = try_init (memctl, CONFIG_SYS_LSDMR_8COL, CONFIG_SYS_OR2_8COL, |
| (uchar *) SDRAM_BASE2_PRELIM); |
| printf ("Local:8COL - %ld MB) using ", lsize >> 20); |
| } |
| |
| #if 0 |
| /* Set up BR2 so that the local SDRAM goes |
| * right after the 60x SDRAM |
| */ |
| memctl->memc_br2 = (CONFIG_SYS_BR2_PRELIM & ~BRx_BA_MSK) | |
| (CONFIG_SYS_SDRAM_BASE + psize); |
| #endif |
| #endif /* CONFIG_SYS_INIT_LOCAL_SDRAM */ |
| #endif /* CONFIG_SYS_RAMBOOT */ |
| |
| icache_enable (); |
| |
| config_scoh_cs (); |
| |
| return (psize); |
| } |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| static void config_scoh_cs (void) |
| { |
| volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR; |
| volatile memctl8260_t *memctl = &immr->im_memctl; |
| volatile can_reg_t *can = (volatile can_reg_t *) CONFIG_SYS_CAN0_BASE; |
| __maybe_unused volatile uint tmp, i; |
| |
| /* Initialize OR3 / BR3 for CAN Bus Controller 0 */ |
| memctl->memc_or3 = CONFIG_SYS_CAN0_OR3; |
| memctl->memc_br3 = CONFIG_SYS_CAN0_BR3; |
| /* Initialize OR4 / BR4 for CAN Bus Controller 1 */ |
| memctl->memc_or4 = CONFIG_SYS_CAN1_OR4; |
| memctl->memc_br4 = CONFIG_SYS_CAN1_BR4; |
| |
| /* Initialize MAMR to write in the array at address 0x0 */ |
| memctl->memc_mamr = 0x00 | MxMR_OP_WARR | MxMR_GPL_x4DIS; |
| |
| /* Initialize UPMA for CAN: single read */ |
| memctl->memc_mdr = 0xcffeec00; |
| udelay (1); /* Necessary to have the data correct in the UPM array!!!! */ |
| /* The read on the CAN controller write the data of mdr in UPMA array. */ |
| /* The index to the array will be incremented automatically |
| through this read */ |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x0ffcec00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x0ffcec00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x0ffcec00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x0ffcec00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x0ffcfc00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x0ffcfc00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0xfffdec07; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| |
| /* Initialize MAMR to write in the array at address 0x18 */ |
| memctl->memc_mamr = 0x18 | MxMR_OP_WARR | MxMR_GPL_x4DIS; |
| |
| /* Initialize UPMA for CAN: single write */ |
| memctl->memc_mdr = 0xfcffec00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x00ffec00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x00ffec00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x00ffec00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x00ffec00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x00fffc00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x00fffc00; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| memctl->memc_mdr = 0x30ffec07; |
| udelay (1); |
| tmp = can->cpu_interface; |
| |
| /* Initialize MAMR */ |
| memctl->memc_mamr = MxMR_GPL_x4DIS; /* GPL_B4 ouput line Disable */ |
| |
| |
| /* Initialize OR5 / BR5 for the extended EEPROM Bank0 */ |
| memctl->memc_or5 = CONFIG_SYS_EXTPROM_OR5; |
| memctl->memc_br5 = CONFIG_SYS_EXTPROM_BR5; |
| /* Initialize OR6 / BR6 for the extended EEPROM Bank1 */ |
| memctl->memc_or6 = CONFIG_SYS_EXTPROM_OR6; |
| memctl->memc_br6 = CONFIG_SYS_EXTPROM_BR6; |
| |
| /* Initialize OR7 / BR7 for the Glue Logic */ |
| memctl->memc_or7 = CONFIG_SYS_FIOX_OR7; |
| memctl->memc_br7 = CONFIG_SYS_FIOX_BR7; |
| |
| /* Initialize OR8 / BR8 for the DOH Logic */ |
| memctl->memc_or8 = CONFIG_SYS_FDOHM_OR8; |
| memctl->memc_br8 = CONFIG_SYS_FDOHM_BR8; |
| |
| DEBUGF ("OR0 %08x BR0 %08x\n", memctl->memc_or0, memctl->memc_br0); |
| DEBUGF ("OR1 %08x BR1 %08x\n", memctl->memc_or1, memctl->memc_br1); |
| DEBUGF ("OR2 %08x BR2 %08x\n", memctl->memc_or2, memctl->memc_br2); |
| DEBUGF ("OR3 %08x BR3 %08x\n", memctl->memc_or3, memctl->memc_br3); |
| DEBUGF ("OR4 %08x BR4 %08x\n", memctl->memc_or4, memctl->memc_br4); |
| DEBUGF ("OR5 %08x BR5 %08x\n", memctl->memc_or5, memctl->memc_br5); |
| DEBUGF ("OR6 %08x BR6 %08x\n", memctl->memc_or6, memctl->memc_br6); |
| DEBUGF ("OR7 %08x BR7 %08x\n", memctl->memc_or7, memctl->memc_br7); |
| DEBUGF ("OR8 %08x BR8 %08x\n", memctl->memc_or8, memctl->memc_br8); |
| |
| DEBUGF ("UPMA addr 0x0\n"); |
| memctl->memc_mamr = 0x00 | MxMR_OP_RARR | MxMR_GPL_x4DIS; |
| for (i = 0; i < 0x8; i++) { |
| tmp = can->cpu_interface; |
| udelay (1); |
| DEBUGF (" %08x ", memctl->memc_mdr); |
| } |
| DEBUGF ("\nUPMA addr 0x18\n"); |
| memctl->memc_mamr = 0x18 | MxMR_OP_RARR | MxMR_GPL_x4DIS; |
| for (i = 0; i < 0x8; i++) { |
| tmp = can->cpu_interface; |
| udelay (1); |
| DEBUGF (" %08x ", memctl->memc_mdr); |
| } |
| DEBUGF ("\n"); |
| memctl->memc_mamr = MxMR_GPL_x4DIS; |
| } |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| int misc_init_r (void) |
| { |
| fpga_init (); |
| return (0); |
| } |
| |
| /* ------------------------------------------------------------------------- */ |