| /* |
| * (C) Copyright 2001 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define MV_VERSION "v0.2.0" |
| |
| /* LED0 = Power , LED1 = Error , LED2-5 = error code, LED6-7=00 -->PPCBoot error */ |
| #define ERR_NONE 0 |
| #define ERR_ENV 1 |
| #define ERR_BOOTM_BADMAGIC 2 |
| #define ERR_BOOTM_BADCRC 3 |
| #define ERR_BOOTM_GUNZIP 4 |
| #define ERR_BOOTP_TIMEOUT 5 |
| #define ERR_DHCP 6 |
| #define ERR_TFTP 7 |
| #define ERR_NOLAN 8 |
| #define ERR_LANDRV 9 |
| |
| #define CONFIG_BOARD_TYPES 1 |
| #define MVBLUE_BOARD_BOX 1 |
| #define MVBLUE_BOARD_LYNX 2 |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFF00000 |
| #define CONFIG_SYS_LDSCRIPT "board/mvblue/u-boot.lds" |
| |
| #if 0 |
| #define ERR_LED(code) do { if (code) \ |
| *(volatile char *)(0xff000003) = ( 3 | (code<<4) ) & 0xf3; \ |
| else \ |
| *(volatile char *)(0xff000003) = ( 1 ); \ |
| } while(0) |
| #else |
| #define ERR_LED(code) |
| #endif |
| |
| #define CONFIG_MPC824X 1 |
| #define CONFIG_MPC8245 1 |
| #define CONFIG_MVBLUE 1 |
| |
| #define CONFIG_CLOCKS_IN_MHZ 1 |
| |
| #define CONFIG_BOARD_TYPES 1 |
| |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_BOOTDELAY 3 |
| #define CONFIG_BOOT_RETRY_TIME -1 |
| |
| #define CONFIG_AUTOBOOT_KEYED |
| #define CONFIG_AUTOBOOT_PROMPT \ |
| "autoboot in %d seconds (stop with 's')...\n", bootdelay |
| #define CONFIG_AUTOBOOT_STOP_STR "s" |
| #define CONFIG_ZERO_BOOTDELAY_CHECK |
| #define CONFIG_RESET_TO_RETRY 60 |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_BOOTD |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_ECHO |
| #define CONFIG_CMD_SAVEENV |
| #define CONFIG_CMD_FLASH |
| #define CONFIG_CMD_IMI |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_RUN |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_NISDOMAIN |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_DNS |
| #define CONFIG_BOOTP_DNS2 |
| #define CONFIG_BOOTP_SEND_HOSTNAME |
| #define CONFIG_BOOTP_NTPSERVER |
| #define CONFIG_BOOTP_TIMEOFFSET |
| |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_MAXARGS 16 /* Max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */ |
| |
| #define CONFIG_BOOTCOMMAND "run nfsboot" |
| #define CONFIG_BOOTARGS "root=/dev/mtdblock5 ro rootfstype=jffs2" |
| |
| #define CONFIG_NFSBOOTCOMMAND "bootp; run nfsargs addcons;bootm" |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "console_nr=0\0" \ |
| "dhcp_client_id=mvBOX-XP\0" \ |
| "dhcp_vendor-class-identifier=mvBOX\0" \ |
| "adminboot=setenv bootargs root=/dev/mtdblock5 rw rootfstype=jffs2;run addcons;bootm ffc00000\0" \ |
| "flashboot=setenv bootargs root=/dev/mtdblock5 ro rootfstype=jffs2;run addcons;bootm ffc00000\0" \ |
| "safeboot=setenv bootargs root=/dev/mtdblock2 rw rootfstype=cramfs;run addcons;bootm ffc00000\0" \ |
| "hdboot=setenv bootargs root=/dev/hda1;run addcons;bootm ffc00000\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0" \ |
| "addcons=setenv bootargs ${bootargs} console=ttyS${console_nr},${baudrate}N8\0" \ |
| "mv_version=" MV_VERSION "\0" \ |
| "bootretry=30\0" |
| |
| #define CONFIG_OVERWRITE_ETHADDR_ONCE |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------- |
| */ |
| |
| #define CONFIG_PCI |
| #define CONFIG_PCI_PNP |
| #define CONFIG_PCI_SCAN_SHOW |
| |
| #define CONFIG_NET_RETRY_COUNT 5 |
| |
| #define CONFIG_TULIP |
| #define CONFIG_TULIP_FIX_DAVICOM 1 |
| #define CONFIG_ETHADDR b6:b4:45:eb:fb:c0 |
| |
| #define CONFIG_HW_WATCHDOG |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| |
| #define CONFIG_SYS_FLASH_BASE 0xFFF00000 |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| |
| #define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 |
| #define CONFIG_SYS_EUMB_ADDR 0xFC000000 |
| |
| #define CONFIG_SYS_MONITOR_LEN 0x00100000 |
| #define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */ |
| |
| /* Maximum amount of RAM. */ |
| #define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 0 .. 256MB of (S)DRAM */ |
| |
| |
| #if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE |
| #undef CONFIG_SYS_RAMBOOT |
| #else |
| #define CONFIG_SYS_RAMBOOT |
| #endif |
| |
| #define CONFIG_SYS_ISA_IO 0xFE000000 |
| |
| /* |
| * serial configuration |
| */ |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600) |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| * For the detail description refer to the MPC8240 user's manual. |
| */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33000000 |
| #define CONFIG_SYS_HZ 10000 |
| |
| /* Bit-field values for MCCR1. */ |
| #define CONFIG_SYS_ROMNAL 7 |
| #define CONFIG_SYS_ROMFAL 11 |
| |
| /* Bit-field values for MCCR2. */ |
| #define CONFIG_SYS_TSWAIT 0x5 |
| #define CONFIG_SYS_REFINT 430 |
| |
| /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */ |
| #define CONFIG_SYS_BSTOPRE 121 |
| |
| /* Bit-field values for MCCR3. */ |
| #define CONFIG_SYS_REFREC 8 |
| |
| /* Bit-field values for MCCR4. */ |
| #define CONFIG_SYS_PRETOACT 3 |
| #define CONFIG_SYS_ACTTOPRE 5 |
| #define CONFIG_SYS_ACTORW 3 |
| #define CONFIG_SYS_SDMODE_CAS_LAT 3 |
| #define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 |
| #define CONFIG_SYS_EXTROM 1 |
| #define CONFIG_SYS_REGDIMM 0 |
| #define CONFIG_SYS_DBUS_SIZE2 1 |
| #define CONFIG_SYS_SDMODE_WRAP 0 |
| |
| #define CONFIG_SYS_PGMAX 0x32 |
| #define CONFIG_SYS_SDRAM_DSCD 0x20 |
| |
| /* Memory bank settings. |
| * Only bits 20-29 are actually used from these vales to set the |
| * start/end addresses. The upper two bits will always be 0, and the lower |
| * 20 bits will be 0x00000 for a start address, or 0xfffff for an end |
| * address. Refer to the MPC8240 book. |
| */ |
| |
| #define CONFIG_SYS_BANK0_START 0x00000000 |
| #define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) |
| #define CONFIG_SYS_BANK0_ENABLE 1 |
| #define CONFIG_SYS_BANK1_START 0x3ff00000 |
| #define CONFIG_SYS_BANK1_END 0x3fffffff |
| #define CONFIG_SYS_BANK1_ENABLE 0 |
| #define CONFIG_SYS_BANK2_START 0x3ff00000 |
| #define CONFIG_SYS_BANK2_END 0x3fffffff |
| #define CONFIG_SYS_BANK2_ENABLE 0 |
| #define CONFIG_SYS_BANK3_START 0x3ff00000 |
| #define CONFIG_SYS_BANK3_END 0x3fffffff |
| #define CONFIG_SYS_BANK3_ENABLE 0 |
| #define CONFIG_SYS_BANK4_START 0x3ff00000 |
| #define CONFIG_SYS_BANK4_END 0x3fffffff |
| #define CONFIG_SYS_BANK4_ENABLE 0 |
| #define CONFIG_SYS_BANK5_START 0x3ff00000 |
| #define CONFIG_SYS_BANK5_END 0x3fffffff |
| #define CONFIG_SYS_BANK5_ENABLE 0 |
| #define CONFIG_SYS_BANK6_START 0x3ff00000 |
| #define CONFIG_SYS_BANK6_END 0x3fffffff |
| #define CONFIG_SYS_BANK6_ENABLE 0 |
| #define CONFIG_SYS_BANK7_START 0x3ff00000 |
| #define CONFIG_SYS_BANK7_END 0x3fffffff |
| #define CONFIG_SYS_BANK7_ENABLE 0 |
| |
| #define CONFIG_SYS_ODCR 0xff |
| |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| |
| #define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| #define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L |
| #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U |
| #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #undef CONFIG_SYS_FLASH_PROTECTION |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 63 /* Max number of sectors per flash */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 12000 |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 1000 |
| |
| |
| #define CONFIG_ENV_IS_IN_FLASH |
| |
| #define CONFIG_ENV_OFFSET 0x00010000 |
| #define CONFIG_ENV_SIZE 0x00010000 |
| #define CONFIG_ENV_SECT_SIZE 0x00010000 |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 32 |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| #endif /* __CONFIG_H */ |