| /* |
| * Copyright 2009-2010 eXMeritus, A Boeing Company |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* |
| * HardwareWall HWW-1U-1A airborne unit configuration file |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High-level system configuration options */ |
| #define CONFIG_BOOKE /* Power/PowerPC Book-E */ |
| #define CONFIG_E500 /* e500 (Power ISA v2.03 with SPE) */ |
| #define CONFIG_MPC85xx /* MPC8540/60/55/41/48 family */ |
| #define CONFIG_FSL_ELBC /* FreeScale Enhanced LocalBus Cntlr */ |
| #define CONFIG_FSL_LAW /* FreeScale Local Access Window */ |
| #define CONFIG_P2020 /* FreeScale P2020 */ |
| #define CONFIG_HWW1U1A /* eXMeritus HardwareWall HWW-1U-1A */ |
| #define CONFIG_MP /* Multiprocessing support */ |
| #define CONFIG_HWCONFIG /* Use hwconfig from environment */ |
| |
| #define CONFIG_L2_CACHE /* L2 cache enabled */ |
| #define CONFIG_BTB /* Branch predition enabled */ |
| |
| #define CONFIG_PANIC_HANG /* No board reset on panic */ |
| #define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r() */ |
| #define CONFIG_CMD_REGINFO /* Dump various CPU regs */ |
| |
| /* |
| * Allow the use of 36-bit physical addresses. Device-trees with 64-bit |
| * addresses have known compatibility issues with some existing kernels. |
| */ |
| #define CONFIG_ENABLE_36BIT_PHYS |
| #define CONFIG_PHYS_64BIT |
| #define CONFIG_ADDR_MAP |
| #define CONFIG_SYS_NUM_ADDR_MAP 16 /* Number of entries in TLB1 */ |
| |
| /* Reserve plenty of RAM for malloc (we have 2GB+) */ |
| #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) |
| |
| /* How much L2 cache do we map so we can use it as RAM */ |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 |
| |
| /* This is our temporary global data area just above the stack */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| /* The stack grows down from the global data area */ |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* Enable IRQs and watchdog with a 1000Hz system decrementer */ |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_SYS_HZ 1000 |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* |
| * Clock crystal configuration: |
| * (1) SYS: 66.666MHz +/- 50ppm (drives CPU/PCI/DDR) |
| * (2) CCB: Multiplier from SYS_CLK |
| * (3) RTC: 25.000MHz +/- 50ppm (sampled against CCB clock) |
| */ |
| #define CONFIG_SYS_CLK_FREQ 66666000/*Hz*/ |
| #define CONFIG_DDR_CLK_FREQ 66666000/*Hz*/ |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* |
| * Memory map |
| * |
| * 0x0000_0000 0x7fff_ffff 2G DDR2 ECC SDRAM |
| * 0x8000_0000 0x9fff_ffff 512M PCI-E Bus 1 |
| * 0xa000_0000 0xbfff_ffff 512M PCI-E Bus 2 (unused) |
| * 0xc000_0000 0xdfff_ffff 512M PCI-E Bus 3 |
| * 0xe000_0000 0xe7ff_ffff 128M Spansion FLASH |
| * 0xe800_0000 0xefff_ffff 128M Spansion FLASH |
| * 0xffd0_0000 0xffd0_3fff 16K L1 boot stack (TLB0) |
| * 0xffe0_0000 0xffef_ffff 1M CCSR |
| * 0xffe0_5000 0xffe0_5fff 4K Enhanced LocalBus Controller |
| */ |
| |
| /* Virtual Memory Map */ |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 |
| #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 |
| #define CONFIG_SYS_FLASH_BASE 0xe0000000 |
| #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 |
| #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 |
| #define CONFIG_SYS_CCSRBAR 0xffe00000 /* CCSRBAR @ runtime */ |
| |
| #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ |
| #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ |
| |
| /* Physical Memory Map */ |
| #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull |
| #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull |
| #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull |
| #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull |
| #define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull |
| #define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull |
| #define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfffd00000ull |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf /* for ASM code */ |
| #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xffd00000 /* for ASM code */ |
| #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0xf /* for ASM code */ |
| #define CONFIG_SYS_CCSRBAR_PHYS_LOW 0xffe00000 /* for ASM code */ |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* U-Boot image (MONITOR_BASE == TEXT_BASE) */ |
| #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc /* Top address in flash */ |
| #define CONFIG_SYS_TEXT_BASE 0xeff80000 /* Start of U-Boot image */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_MONITOR_LEN 0x80000 /* 512kB (4 flash sectors) */ |
| |
| /* |
| * U-Boot Environment Image: The two sectors immediately below U-Boot |
| * form the U-Boot environment (regular and redundant). |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH /* The environment image is stored in FLASH */ |
| #define CONFIG_ENV_OVERWRITE /* Allow "protected" variables to be erased */ |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128kB (1 flash sector) */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) |
| |
| /* Only use 8kB of each environment sector for data */ |
| #define CONFIG_ENV_SIZE 0x2000 /* 8kB */ |
| #define CONFIG_ENV_SIZE_REDUND 0x2000 /* 8kB */ |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* Serial Console Configuration */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) |
| |
| /* Echo back characters received during a serial download */ |
| #define CONFIG_LOADS_ECHO |
| |
| /* Allow a serial-download to temporarily change baud */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* PCI and PCI-Express Support */ |
| #define CONFIG_PCI /* Enable PCI/PCIE */ |
| #define CONFIG_PCI_PNP /* Scan PCI busses */ |
| #define CONFIG_CMD_PCI /* Enable the "pci" command */ |
| #define CONFIG_FSL_PCI_INIT /* Common FreeScale PCI initialization */ |
| #define CONFIG_FSL_PCIE_RESET /* We have PCI-E reset errata */ |
| #define CONFIG_SYS_PCI_64BIT /* PCI resources are 64-bit */ |
| #define CONFIG_PCI_SCAN_SHOW /* Display PCI scan during boot */ |
| |
| /* Enable 2 of the 3 PCI-E controllers */ |
| #define CONFIG_PCIE3 |
| #undef CONFIG_PCIE2 |
| #define CONFIG_PCIE1 |
| |
| /* Display human-readable names when initializing */ |
| #define CONFIG_SYS_PCIE3_NAME "Intel 82571EB" |
| #define CONFIG_SYS_PCIE2_NAME "Unused" |
| #define CONFIG_SYS_PCIE1_NAME "Silicon Image SIL3531" |
| |
| /* |
| * PCI bus addresses |
| * Memory space is mapped 1-1, but I/O space must start from 0. |
| */ |
| #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* Generic FreeScale hardware I2C support */ |
| #define CONFIG_HARD_I2C |
| #define CONFIG_FSL_I2C |
| #define CONFIG_CMD_I2C |
| #define CONFIG_I2C_MULTI_BUS |
| #define CONFIG_SYS_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_I2C2_OFFSET 0x3100 |
| |
| /* I2C bus configuration */ |
| #define CONFIG_SYS_I2C_SPEED 400000 |
| #define CONFIG_SYS_I2C_SLAVE 0x7F |
| |
| /* DDR2 SO-RDIMM SPD EEPROM is at I2C0-0x51 */ |
| #define CONFIG_SYS_SPD_BUS_NUM 0 |
| #define SPD_EEPROM_ADDRESS 0x51 |
| |
| /* DS1339 RTC is at I2C0-0x68 (I know it says "DS1337", it's a DS1339) */ |
| #define CONFIG_CMD_DATE |
| #define CONFIG_RTC_DS1337 |
| #define CONFIG_SYS_RTC_BUS_NUM 0 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| /* Turn off RTC square-wave output to save battery */ |
| #define CONFIG_SYS_RTC_DS1337_NOOSC |
| |
| /* |
| * AT24C128N EEPROM at I2C0-0x53. |
| * |
| * That Atmel EEPROM has 128kbit of memory (16kByte) divided into 256 pages |
| * of 64 bytes per page. The chip uses 2-byte addresses and has a max write |
| * cycle time of 20ms according to the datasheet. |
| * |
| * NOTE: Our environment is stored on regular direct-attached FLASH, this |
| * chip is only used as a write-protected backup for certain key settings |
| * such as the serial# and macaddr values. (EG: "env import") |
| */ |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_ENV_EEPROM_IS_ON_I2C |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 1 << 6 == 64 byte pages */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 21 |
| |
| /* |
| * PCA9554 is at I2C1-0x3f (I know it says "PCA953X", it's a PCA9554). You |
| * must first select the I2C1 bus with "i2c dev 1" or the "pca953x" command |
| * will not be able to access the chip. |
| */ |
| #define CONFIG_PCA953X |
| #define CONFIG_CMD_PCA953X |
| #define CONFIG_CMD_PCA953X_INFO |
| #define CONFIG_SYS_I2C_PCA953X_ADDR 0x3f |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* FreeScale DDR2/3 SDRAM Controller */ |
| #define CONFIG_FSL_DDR2 /* Our SDRAM slot is DDR2 */ |
| #define CONFIG_DDR_ECC /* Enable ECC by default */ |
| #define CONFIG_DDR_SPD /* Detect DDR config from SPD EEPROM */ |
| #define CONFIG_SPD_EEPROM /* ...why 2 config variables for this? */ |
| #define CONFIG_VERY_BIG_RAM /* Allow 2GB+ of RAM */ |
| #define CONFIG_CMD_SDRAM |
| |
| /* Standard P2020 DDR controller parameters */ |
| #define CONFIG_NUM_DDR_CONTROLLERS 1 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL 2 |
| |
| /* Make sure to tell the DDR controller to preinitialze all of RAM */ |
| #define CONFIG_MEM_INIT_VALUE 0xDEADBEEF |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* FLASH Memory Configuration (2x 128MB SPANSION FLASH) */ |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 |
| |
| /* Flash banks (2x 128MB) */ |
| #define FLASH0_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000ull) |
| #define FLASH1_PHYS (CONFIG_SYS_FLASH_BASE_PHYS + 0x0000000ull) |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 |
| #define CONFIG_SYS_FLASH_BANKS_LIST { FLASH0_PHYS, FLASH1_PHYS } |
| |
| /* |
| * Flash access modes and timings (values are the defaults after a RESET). |
| * |
| * NOTE: These could probably be optimized but are more than sufficient for |
| * this particular system for the moment. |
| */ |
| #define FLASH_BRx (BR_PS_16 | BR_MS_GPCM | BR_V) |
| #define FLASH_ORx (OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS \ |
| | OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) |
| |
| /* Configure both flash banks */ |
| #define CONFIG_SYS_BR0_PRELIM (FLASH_BRx | BR_PHYS_ADDR(FLASH0_PHYS)) |
| #define CONFIG_SYS_BR1_PRELIM (FLASH_BRx | BR_PHYS_ADDR(FLASH1_PHYS)) |
| #define CONFIG_SYS_OR0_PRELIM (FLASH_ORx | OR_AM_128MB) |
| #define CONFIG_SYS_OR1_PRELIM (FLASH_ORx | OR_AM_128MB) |
| |
| /* Flash timeouts (in ms) */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000UL /* Erase (60s) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500UL /* Write (0.5s) */ |
| |
| /* Quiet flash testing */ |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| |
| /* Make program/erase count down from 45/5 (9....8....7....) */ |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* Ethernet Device Support */ |
| #define CONFIG_MII /* Enable MII PHY code */ |
| #define CONFIG_MII_DEFAULT_TSEC /* ??? Copied from P2020DS */ |
| #define CONFIG_PHY_GIGE /* Support Gigabit PHYs */ |
| #define CONFIG_ETHPRIME "e1000#0" /* Default to external ports */ |
| |
| /* Turn on various helpful networking commands */ |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_PING |
| |
| /* On-chip FreeScale P2020 "tsec" Ethernet (oneway fibers and peer) */ |
| #define CONFIG_TSEC_ENET |
| #define CONFIG_TSEC1 |
| #define CONFIG_TSEC2 |
| #define CONFIG_TSEC3 |
| #define CONFIG_TSEC1_NAME "owt0" |
| #define CONFIG_TSEC2_NAME "owt1" |
| #define CONFIG_TSEC3_NAME "peer" |
| #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC3_PHYIDX 0 |
| #define TSEC1_PHY_ADDR 2 |
| #define TSEC2_PHY_ADDR 3 |
| #define TSEC3_PHY_ADDR 4 |
| #define TSEC3_PHY_ADDR_CPUA 4 |
| #define TSEC3_PHY_ADDR_CPUB 5 |
| |
| /* PCI-E dual-port E1000 (external ethernet ports) */ |
| #define CONFIG_E1000 |
| #define CONFIG_E1000_SPI |
| #define CONFIG_E1000_SPI_GENERIC |
| #define CONFIG_CMD_E1000 |
| |
| /* We need the SPI infrastructure to poke the E1000's EEPROM */ |
| #define CONFIG_SPI |
| #define CONFIG_SPI_X |
| #define CONFIG_CMD_SPI |
| #define MAX_SPI_BYTES 32 |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* USB Thumbdrive Device Support */ |
| #define CONFIG_USB_EHCI |
| #define CONFIG_USB_EHCI_FSL |
| #define CONFIG_USB_STORAGE |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #define CONFIG_CMD_USB |
| |
| /* Partition and Filesystem support */ |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_EFI_PARTITION |
| #define CONFIG_ISO_PARTITION |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_CMD_FAT |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* Command line configuration. */ |
| #define CONFIG_CMDLINE_EDITING /* Enable command editing */ |
| #define CONFIG_COMMAND_HISTORY /* Enable command history */ |
| #define CONFIG_AUTO_COMPLETE /* Enable command completion */ |
| #define CONFIG_SYS_LONGHELP /* Enable detailed command help */ |
| #define CONFIG_SYS_MAXARGS 128 /* Up to 128 command-line args */ |
| #define CONFIG_SYS_PBSIZE 8192 /* Allow up to 8k printed lines */ |
| #define CONFIG_SYS_CBSIZE 4096 /* Allow up to 4k command lines */ |
| #define CONFIG_SYS_BARGSIZE 4096 /* Allow up to 4k boot args */ |
| #define CONFIG_SYS_HUSH_PARSER /* Enable a fancier shell */ |
| |
| /* A little extra magic here for the prompt */ |
| #define CONFIG_SYS_PROMPT hww1u1a_get_ps1() |
| #ifndef __ASSEMBLY__ |
| const char *hww1u1a_get_ps1(void); |
| #endif |
| |
| /* Include a bunch of default commands we probably want */ |
| #include <config_cmd_default.h> |
| |
| /* Other helpful shell-like commands */ |
| #define CONFIG_MD5 |
| #define CONFIG_SHA1 |
| #define CONFIG_CMD_MD5SUM |
| #define CONFIG_CMD_SHA1SUM |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_SETEXPR |
| |
| |
| /* -------------------------------------------------------------------- */ |
| |
| /* Image manipulation and booting */ |
| |
| /* We use the OpenFirmware-esque "Flattened Device Tree" */ |
| #define CONFIG_OF_LIBFDT |
| #define CONFIG_OF_BOARD_SETUP |
| #define CONFIG_OF_STDOUT_VIA_ALIAS |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 64 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_CMD_ELF |
| #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Maximum kernel memory map */ |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Maximum kernel size of 64MB */ |
| |
| /* This is the default address for commands with an optional address arg */ |
| #define CONFIG_LOADADDR 100000 |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 |
| |
| /* Test memory starting from the default load address to just below 2GB */ |
| #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_LOAD_ADDR |
| #define CONFIG_SYS_MEMTEST_END 0x7f000000 |
| |
| #define CONFIG_BOOTDELAY 20 |
| #define CONFIG_BOOTCOMMAND "echo Not yet flashed" |
| #define CONFIG_BOOTARGS "" |
| #define CONFIG_BOOTARGS_DYNAMIC "console=ttyS0,${baudrate}n1" |
| |
| /* Extra environment parameters */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "ethprime=e1000#0\0" \ |
| "ethrotate=no\0" \ |
| "setbootargs=setenv bootargs " \ |
| "\"${bootargs} "CONFIG_BOOTARGS_DYNAMIC"\"\0" \ |
| "perf_mode=performance\0" \ |
| "hwconfig=" "fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1;" \ |
| "usb1:dr_mode=host,phy_type=ulpi\0" \ |
| "flkernel=0xe8000000\0" \ |
| "flinitramfs=0xe8800000\0" \ |
| "fldevicetree=0xeff20000\0" \ |
| "flbootm=bootm ${flkernel} ${flinitramfs} ${fldevicetree}\0" \ |
| "flboot=run preboot; run flbootm\0" \ |
| "restore_eeprom=i2c dev 0 && " \ |
| "eeprom read $loadaddr 0x0000 0x2000 && " \ |
| "env import -c $loadaddr 0x2000\0" |
| |
| #endif /* __CONFIG_H */ |