| /* |
| * SPDX-License-Identifier: GPL-2.0 IBM-pibs |
| */ |
| #include <config.h> |
| #include <asm/ppc4xx.h> |
| |
| #include <ppc_asm.tmpl> |
| #include <ppc_defs.h> |
| |
| #include <asm/cache.h> |
| #include <asm/mmu.h> |
| |
| /****************************************************************************** |
| * Function: ext_bus_cntlr_init |
| * |
| * Description: Configures EBC Controller and a few basic chip selects. |
| * |
| * CS0 is setup to get the Boot Flash out of the addresss range |
| * so that we may setup a stack. CS7 is setup so that we can |
| * access and reset the hardware watchdog. |
| * |
| * IMPORTANT: For pass1 this code must run from |
| * cache since you can not reliably change a peripheral banks |
| * timing register (pbxap) while running code from that bank. |
| * For ex., since we are running from ROM on bank 0, we can NOT |
| * execute the code that modifies bank 0 timings from ROM, so |
| * we run it from cache. |
| * |
| * Notes: Does NOT use the stack. |
| *****************************************************************************/ |
| .section ".text" |
| .align 2 |
| .globl ext_bus_cntlr_init |
| .type ext_bus_cntlr_init, @function |
| ext_bus_cntlr_init: |
| mflr r0 |
| /******************************************************************** |
| * Prefetch entire ext_bus_cntrl_init function into the icache. |
| * This is necessary because we are going to change the same CS we |
| * are executing from. Otherwise a CPU lockup may occur. |
| *******************************************************************/ |
| bl ..getAddr |
| ..getAddr: |
| mflr r3 /* get address of ..getAddr */ |
| |
| /* Calculate number of cache lines for this function */ |
| addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2) |
| mtctr r4 |
| ..ebcloop: |
| icbt r0, r3 /* prefetch cache line for addr in r3*/ |
| addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */ |
| bdnz ..ebcloop /* continue for $CTR cache lines */ |
| |
| /******************************************************************** |
| * Delay to ensure all accesses to ROM are complete before changing |
| * bank 0 timings. 200usec should be enough. |
| * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles. |
| *******************************************************************/ |
| addis r3, 0, 0x0 |
| ori r3, r3, 0xA000 /* wait 200us from reset */ |
| mtctr r3 |
| ..spinlp: |
| bdnz ..spinlp /* spin loop */ |
| |
| /******************************************************************** |
| * Setup External Bus Controller (EBC). |
| *******************************************************************/ |
| addi r3, 0, EBC0_CFG |
| mtdcr EBC0_CFGADDR, r3 |
| addis r4, 0, 0xb040 /* Device base timeout = 1024 cycles */ |
| ori r4, r4, 0x0 /* Drive CS with external master */ |
| mtdcr EBC0_CFGDATA, r4 |
| |
| /******************************************************************** |
| * Change PCIINT signal to PerWE |
| *******************************************************************/ |
| mfdcr r4, CPC0_CR1 |
| ori r4, r4, 0x4000 |
| mtdcr CPC0_CR1, r4 |
| |
| /******************************************************************** |
| * Memory Bank 0 (Flash Bank 0) initialization |
| *******************************************************************/ |
| addi r3, 0, PB1AP |
| mtdcr EBC0_CFGADDR, r3 |
| addis r4, 0, CONFIG_SYS_W7O_EBC_PB0AP@h |
| ori r4, r4, CONFIG_SYS_W7O_EBC_PB0AP@l |
| mtdcr EBC0_CFGDATA, r4 |
| |
| addi r3, 0, PB0CR |
| mtdcr EBC0_CFGADDR, r3 |
| addis r4, 0, CONFIG_SYS_W7O_EBC_PB0CR@h |
| ori r4, r4, CONFIG_SYS_W7O_EBC_PB0CR@l |
| mtdcr EBC0_CFGDATA, r4 |
| |
| /******************************************************************** |
| * Memory Bank 7 LEDs - NEEDED BECAUSE OF HW WATCHDOG AND LEDs. |
| *******************************************************************/ |
| addi r3, 0, PB7AP |
| mtdcr EBC0_CFGADDR, r3 |
| addis r4, 0, CONFIG_SYS_W7O_EBC_PB7AP@h |
| ori r4, r4, CONFIG_SYS_W7O_EBC_PB7AP@l |
| mtdcr EBC0_CFGDATA, r4 |
| |
| addi r3, 0, PB7CR |
| mtdcr EBC0_CFGADDR, r3 |
| addis r4, 0, CONFIG_SYS_W7O_EBC_PB7CR@h |
| ori r4, r4, CONFIG_SYS_W7O_EBC_PB7CR@l |
| mtdcr EBC0_CFGDATA, r4 |
| |
| /* We are all done */ |
| mtlr r0 /* Restore link register */ |
| blr /* Return to calling function */ |
| .Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init |
| /* end ext_bus_cntlr_init() */ |
| |
| /****************************************************************************** |
| * Function: sdram_init |
| * |
| * Description: Configures SDRAM memory banks. |
| * |
| * Serial Presence Detect, "SPD," reads the SDRAM EEPROM |
| * via the IIC bus and then configures the SDRAM memory |
| * banks appropriately. If Auto Memory Configuration is |
| * is not used, it is assumed that a 4MB 11x8x2, non-ECC, |
| * SDRAM is soldered down. |
| * |
| * Notes: Expects that the stack is already setup. |
| *****************************************************************************/ |
| .section ".text" |
| .align 2 |
| .globl sdram_init |
| .type sdram_init, @function |
| sdram_init: |
| /* save the return info on stack */ |
| mflr r0 /* Get link register */ |
| stwu r1, -8(r1) /* Save back chain and move SP */ |
| stw r0, +12(r1) /* Save link register */ |
| |
| /* |
| * First call spd_sdram to try to init SDRAM according to the |
| * contents of the SPD EEPROM. If the SPD EEPROM is blank or |
| * erronious, spd_sdram returns 0 in R3. |
| */ |
| li r3,0 |
| bl spd_sdram |
| addic. r3, r3, 0 /* Check for error, save dram size */ |
| bne ..sdri_done /* If it worked, we're done... */ |
| |
| /******************************************************************** |
| * If SPD detection fails, we'll default to 4MB, 11x8x2, as this |
| * is the SMALLEST SDRAM size the 405 supports. We can do this |
| * because W7O boards have soldered on RAM, and there will always |
| * be some amount present. If we were using DIMMs, we should hang |
| * the board instead, since it doesn't have any RAM to continue |
| * running with. |
| *******************************************************************/ |
| |
| /* |
| * Disable memory controller to allow |
| * values to be changed. |
| */ |
| addi r3, 0, SDRAM0_CFG |
| mtdcr SDRAM0_CFGADDR, r3 |
| addis r4, 0, 0x0 |
| ori r4, r4, 0x0 |
| mtdcr SDRAM0_CFGDATA, r4 |
| |
| /* |
| * Set MB0CF for ext bank 0. (0-4MB) Address Mode 5 since 11x8x2 |
| * All other banks are disabled. |
| */ |
| addi r3, 0, SDRAM0_B0CR |
| mtdcr SDRAM0_CFGADDR, r3 |
| addis r4, 0, 0x0000 /* BA=0x0, SZ=4MB */ |
| ori r4, r4, 0x8001 /* Mode is 5, 11x8x2or4, BE=Enabled */ |
| mtdcr SDRAM0_CFGDATA, r4 |
| |
| /* Clear MB1CR,MB2CR,MB3CR to turn other banks off */ |
| addi r4, 0, 0 /* Zero the data reg */ |
| |
| addi r3, r3, 4 /* Point to MB1CF reg */ |
| mtdcr SDRAM0_CFGADDR, r3 /* Set the address */ |
| mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */ |
| |
| addi r3, r3, 4 /* Point to MB2CF reg */ |
| mtdcr SDRAM0_CFGADDR, r3 /* Set the address */ |
| mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */ |
| |
| addi r3, r3, 4 /* Point to MB3CF reg */ |
| mtdcr SDRAM0_CFGADDR, r3 /* Set the address */ |
| mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */ |
| |
| /******************************************************************** |
| * Set the SDRAM Timing reg, SDTR1 and the refresh timer reg, RTR. |
| * To set the appropriate timings, we assume sdram is |
| * 100MHz (pc100 compliant). |
| *******************************************************************/ |
| |
| /* |
| * Set up SDTR1 |
| */ |
| addi r3, 0, SDRAM0_TR |
| mtdcr SDRAM0_CFGADDR, r3 |
| addis r4, 0, 0x0086 /* SDTR1 value for 100Mhz */ |
| ori r4, r4, 0x400D |
| mtdcr SDRAM0_CFGDATA, r4 |
| |
| /* |
| * Set RTR |
| */ |
| addi r3, 0, SDRAM0_RTR |
| mtdcr SDRAM0_CFGADDR, r3 |
| addis r4, 0, 0x05F0 /* RTR refresh val = 15.625ms@100Mhz */ |
| mtdcr SDRAM0_CFGDATA, r4 |
| |
| /******************************************************************** |
| * Delay to ensure 200usec have elapsed since reset. Assume worst |
| * case that the core is running 200Mhz: |
| * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles |
| *******************************************************************/ |
| addis r3, 0, 0x0000 |
| ori r3, r3, 0xA000 /* Wait 200us from reset */ |
| mtctr r3 |
| ..spinlp2: |
| bdnz ..spinlp2 /* spin loop */ |
| |
| /******************************************************************** |
| * Set memory controller options reg, MCOPT1. |
| *******************************************************************/ |
| addi r3, 0, SDRAM0_CFG |
| mtdcr SDRAM0_CFGADDR, r3 |
| addis r4, 0, 0x80E0 /* DC_EN=1,SRE=0,PME=0,MEMCHK=0 */ |
| ori r4, r4, 0x0000 /* REGEN=0,DRW=00,BRPF=01,ECCDD=1 */ |
| mtdcr SDRAM0_CFGDATA, r4 /* EMDULR=1 */ |
| |
| ..sdri_done: |
| /* restore and return */ |
| lwz r0, +12(r1) /* Get saved link register */ |
| addi r1, r1, +8 /* Remove frame from stack */ |
| mtlr r0 /* Restore link register */ |
| blr /* Return to calling function */ |
| .Lfe1: .size sdram_init,.Lfe1-sdram_init |
| /* end sdram_init() */ |