| /* |
| * (C) Copyright 2007 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <asm-offsets.h> |
| #include <ppc_asm.tmpl> |
| #include <config.h> |
| #include <asm/mmu.h> |
| |
| /************************************************************************** |
| * TLB TABLE |
| * |
| * This table is used by the cpu boot code to setup the initial tlb |
| * entries. Rather than make broad assumptions in the cpu source tree, |
| * this table lets each board set things up however they like. |
| * |
| * Pointer to the table is returned in r1 |
| * |
| *************************************************************************/ |
| .section .bootpg,"ax" |
| .globl tlbtab |
| |
| tlbtab: |
| tlbtab_start |
| |
| /* |
| * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the |
| * speed up boot process. It is patched after relocation to enable SA_I |
| */ |
| tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G) |
| |
| /* |
| * TLB entries for SDRAM are not needed on this platform. |
| * They are dynamically generated in the SPD DDR(2) detection |
| * routine. |
| */ |
| |
| #ifdef CONFIG_SYS_INIT_RAM_DCACHE |
| /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ |
| tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G) |
| #endif |
| |
| /* TLB-entry for PCI Memory */ |
| tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_RW | SA_IG) |
| tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_RW | SA_IG) |
| |
| /* TLB-entry for the FPGA Chip select 2 */ |
| tlbentry(CONFIG_SYS_FPGA_BASE_0, SZ_1M, CONFIG_SYS_FPGA_BASE_0, 1, AC_RWX | SA_I|SA_G) |
| |
| /* TLB-entry for the FPGA Chip select 3 */ |
| tlbentry(CONFIG_SYS_FPGA_BASE_1, SZ_1M, CONFIG_SYS_FPGA_BASE_1, 1,AC_RWX | SA_I|SA_G) |
| |
| /* TLB-entry for the LIME Controller */ |
| tlbentry(CONFIG_SYS_LIME_BASE_0, SZ_16M, CONFIG_SYS_LIME_BASE_0, 1, AC_RWX | SA_I|SA_G) |
| tlbentry(CONFIG_SYS_LIME_BASE_1, SZ_16M, CONFIG_SYS_LIME_BASE_1, 1, AC_RWX | SA_I|SA_G) |
| tlbentry(CONFIG_SYS_LIME_BASE_2, SZ_16M, CONFIG_SYS_LIME_BASE_2, 1, AC_RWX | SA_I|SA_G) |
| tlbentry(CONFIG_SYS_LIME_BASE_3, SZ_16M, CONFIG_SYS_LIME_BASE_3, 1, AC_RWX | SA_I|SA_G) |
| |
| /* TLB-entry for Internal Registers & OCM */ |
| tlbentry(0xe0000000, SZ_16M, 0xe0000000, 0, AC_RWX | SA_I) |
| |
| /*TLB-entry PCI registers*/ |
| tlbentry(0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_RWX | SA_IG) |
| |
| /* TLB-entry for peripherals */ |
| tlbentry(0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG) |
| |
| tlbtab_end |