| /* |
| * Configuation settings for the SAMA5D3xEK board. |
| * |
| * Copyright (C) 2012 - 2013 Atmel |
| * |
| * based on at91sam9m10g45ek.h by: |
| * Stelian Pop <stelian@popies.net> |
| * Lead Tech Design <www.leadtechdesign.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * If has No NOR flash, please put the definition: CONFIG_SYS_NO_FLASH |
| * before the common header. |
| */ |
| #include "at91-sama5_common.h" |
| |
| #define CONFIG_BOARD_LATE_INIT |
| #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG |
| |
| /* serial console */ |
| #define CONFIG_ATMEL_USART |
| #define CONFIG_USART_BASE ATMEL_BASE_DBGU |
| #define CONFIG_USART_ID ATMEL_ID_DBGU |
| |
| /* |
| * This needs to be defined for the OHCI code to work but it is defined as |
| * ATMEL_ID_UHPHS in the CPU specific header files. |
| */ |
| #define ATMEL_ID_UHP ATMEL_ID_UHPHS |
| |
| /* |
| * Specify the clock enable bit in the PMC_SCER register. |
| */ |
| #define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP |
| |
| /* LCD */ |
| #define CONFIG_LCD |
| #define LCD_BPP LCD_COLOR16 |
| #define LCD_OUTPUT_BPP 24 |
| #define CONFIG_LCD_LOGO |
| #define CONFIG_LCD_INFO |
| #define CONFIG_LCD_INFO_BELOW_LOGO |
| #define CONFIG_SYS_WHITE_ON_BLACK |
| #define CONFIG_ATMEL_HLCD |
| #define CONFIG_ATMEL_LCD_RGB565 |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV |
| |
| /* board specific (not enough SRAM) */ |
| #define CONFIG_SAMA5D3_LCD_BASE 0x23E00000 |
| |
| /* NOR flash */ |
| #ifndef CONFIG_SYS_NO_FLASH |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_PROTECTION |
| #define CONFIG_SYS_FLASH_BASE 0x10000000 |
| #define CONFIG_SYS_MAX_FLASH_SECT 131 |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| #endif |
| |
| /* SDRAM */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS |
| #define CONFIG_SYS_SDRAM_SIZE 0x20000000 |
| |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_INIT_SP_ADDR 0x310000 |
| #else |
| #define CONFIG_SYS_INIT_SP_ADDR \ |
| (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) |
| #endif |
| |
| /* SerialFlash */ |
| |
| #ifdef CONFIG_CMD_SF |
| #define CONFIG_ATMEL_SPI |
| #define CONFIG_SF_DEFAULT_SPEED 30000000 |
| #endif |
| |
| /* NAND flash */ |
| #define CONFIG_CMD_NAND |
| |
| #ifdef CONFIG_CMD_NAND |
| #define CONFIG_NAND_ATMEL |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 |
| /* our ALE is AD21 */ |
| #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) |
| /* our CLE is AD22 */ |
| #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| /* PMECC & PMERRLOC */ |
| #define CONFIG_ATMEL_NAND_HWECC |
| #define CONFIG_ATMEL_NAND_HW_PMECC |
| #define CONFIG_PMECC_CAP 4 |
| #define CONFIG_PMECC_SECTOR_SIZE 512 |
| #define CONFIG_CMD_NAND_TRIMFFS |
| #endif |
| |
| /* Ethernet Hardware */ |
| #define CONFIG_MACB |
| #define CONFIG_RMII |
| #define CONFIG_NET_RETRY_COUNT 20 |
| #define CONFIG_MACB_SEARCH_PHY |
| #define CONFIG_RGMII |
| #define CONFIG_PHYLIB |
| #define CONFIG_PHY_MICREL |
| #define CONFIG_PHY_MICREL_KSZ9021 |
| |
| /* MMC */ |
| |
| #ifdef CONFIG_CMD_MMC |
| #define CONFIG_MMC |
| #define CONFIG_GENERIC_MMC |
| #define CONFIG_GENERIC_ATMEL_MCI |
| #define ATMEL_BASE_MMCI ATMEL_BASE_MCI0 |
| #endif |
| |
| /* USB */ |
| |
| #ifdef CONFIG_CMD_USB |
| #define CONFIG_USB_ATMEL |
| #define CONFIG_USB_ATMEL_CLK_SEL_UPLL |
| #define CONFIG_USB_OHCI_NEW |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "sama5d3" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3 |
| #define CONFIG_DOS_PARTITION |
| #endif |
| |
| /* USB device */ |
| #define CONFIG_USB_ETHER |
| #define CONFIG_USB_ETH_RNDIS |
| #define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D3xEK" |
| |
| #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) |
| #define CONFIG_FAT_WRITE |
| #endif |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ |
| |
| #ifdef CONFIG_SYS_USE_SERIALFLASH |
| /* override the bootcmd, bootargs and other configuration for spi flash env*/ |
| #elif CONFIG_SYS_USE_NANDFLASH |
| /* override the bootcmd, bootargs and other configuration nandflash env */ |
| #elif CONFIG_SYS_USE_MMC |
| /* override the bootcmd, bootargs and other configuration for sd/mmc env */ |
| #else |
| #define CONFIG_ENV_IS_NOWHERE |
| #endif |
| |
| /* SPL */ |
| #define CONFIG_SPL_FRAMEWORK |
| #define CONFIG_SPL_TEXT_BASE 0x300000 |
| #define CONFIG_SPL_MAX_SIZE 0x10000 |
| #define CONFIG_SPL_BSS_START_ADDR 0x20000000 |
| #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 |
| #define CONFIG_SYS_SPL_MALLOC_START 0x20080000 |
| #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 |
| |
| #define CONFIG_SPL_LIBCOMMON_SUPPORT |
| #define CONFIG_SPL_LIBGENERIC_SUPPORT |
| #define CONFIG_SPL_SERIAL_SUPPORT |
| |
| #define CONFIG_SPL_BOARD_INIT |
| #define CONFIG_SYS_MONITOR_LEN (512 << 10) |
| |
| #ifdef CONFIG_SYS_USE_MMC |
| #define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds |
| #define CONFIG_SPL_MMC_SUPPORT |
| #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400 |
| #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200 |
| #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 |
| #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" |
| #define CONFIG_SPL_LIBDISK_SUPPORT |
| |
| #elif CONFIG_SYS_USE_NANDFLASH |
| #define CONFIG_SPL_NAND_SUPPORT |
| #define CONFIG_SPL_NAND_DRIVERS |
| #define CONFIG_SPL_NAND_BASE |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 |
| #define CONFIG_SYS_NAND_5_ADDR_CYCLE |
| #define CONFIG_SYS_NAND_PAGE_SIZE 0x800 |
| #define CONFIG_SYS_NAND_PAGE_COUNT 64 |
| #define CONFIG_SYS_NAND_OOBSIZE 64 |
| #define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 |
| #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 |
| #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER |
| |
| #elif CONFIG_SYS_USE_SERIALFLASH |
| #define CONFIG_SPL_SPI_SUPPORT |
| #define CONFIG_SPL_SPI_FLASH_SUPPORT |
| #define CONFIG_SPL_SPI_LOAD |
| #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000 |
| |
| #endif |
| |
| #endif |