include/configs/mx7dsabresd.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (C) 2015 Freescale Semiconductor, Inc.
  *
  * Configuration settings for the Freescale i.MX7D SABRESD board.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __MX7D_SABRESD_CONFIG_H
 #define __MX7D_SABRESD_CONFIG_H

 #include "mx7_common.h"

 #define CONFIG_DBG_MONITOR
 #define PHYS_SDRAM_SIZE			SZ_1G

 #define CONFIG_MXC_UART_BASE            UART1_IPS_BASE_ADDR

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)

 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_LATE_INIT

 #define CONFIG_DISPLAY_BOARDINFO

 /* Uncomment to enable secure boot support */
 /* #define CONFIG_SECURE_BOOT */
 #define CONFIG_CSF_SIZE			0x4000

 /* Network */
 #define CONFIG_FEC_MXC
 #define CONFIG_MII
 #define CONFIG_FEC_XCV_TYPE             RGMII
 #define CONFIG_ETHPRIME                 "FEC"
 #define CONFIG_FEC_MXC_PHYADDR          0

 #define CONFIG_PHYLIB
 #define CONFIG_PHY_BROADCOM
 /* ENET1 */
 #define IMX_FEC_BASE			ENET_IPS_BASE_ADDR

 /* MMC Config*/
 #define CONFIG_SYS_FSL_ESDHC_ADDR       0

 /* PMIC */
 #define CONFIG_POWER
 #define CONFIG_POWER_I2C
 #define CONFIG_POWER_PFUZE3000
 #define CONFIG_POWER_PFUZE3000_I2C_ADDR	0x08

 #undef CONFIG_BOOTM_NETBSD
 #undef CONFIG_BOOTM_PLAN9
 #undef CONFIG_BOOTM_RTEMS

 /* I2C configs */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_SPEED		100000

 #define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
 #define CONFIG_SYS_MMC_IMG_LOAD_PART	1

 #ifdef CONFIG_IMX_BOOTAUX
 /* Set to QSPI1 A flash at default */
 #define CONFIG_SYS_AUXCORE_BOOTDATA 0x60000000

 #define UPDATE_M4_ENV \
 	"m4image=m4_qspi.bin\0" \
 	"loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \
 	"update_m4_from_sd=" \
 		"if sf probe 0:0; then " \
 			"if run loadm4image; then " \
 				"setexpr fw_sz ${filesize} + 0xffff; " \
 				"setexpr fw_sz ${fw_sz} / 0x10000; "	\
 				"setexpr fw_sz ${fw_sz} * 0x10000; "	\
 				"sf erase 0x0 ${fw_sz}; " \
 				"sf write ${loadaddr} 0x0 ${filesize}; " \
 			"fi; " \
 		"fi\0" \
 	"m4boot=sf probe 0:0; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"
 #else
 #define UPDATE_M4_ENV ""
 #endif

 #define CONFIG_MFG_ENV_SETTINGS \
 	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
 		"rdinit=/linuxrc " \
 		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
 		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
 		"g_mass_storage.iSerialNumber=\"\" "\
 		"clk_ignore_unused "\
 		"\0" \
 	"initrd_addr=0x83800000\0" \
 	"initrd_high=0xffffffff\0" \
 	"bootcmd_mfg=run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \

 #define CONFIG_DFU_ENV_SETTINGS \
 	"dfu_alt_info=image raw 0 0x800000;"\
 		"u-boot raw 0 0x4000;"\
 		"bootimg part 0 1;"\
 		"rootfs part 0 2\0" \

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	UPDATE_M4_ENV \
 	CONFIG_MFG_ENV_SETTINGS \
 	CONFIG_DFU_ENV_SETTINGS \
 	"script=boot.scr\0" \
 	"image=zImage\0" \
 	"console=ttymxc0\0" \
 	"fdt_high=0xffffffff\0" \
 	"initrd_high=0xffffffff\0" \
 	"fdt_file=imx7d-sdb.dtb\0" \
 	"fdt_addr=0x83000000\0" \
 	"boot_fdt=try\0" \
 	"ip_dyn=yes\0" \
 	"videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \
 	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
 	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
 	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 	"mmcautodetect=yes\0" \
 	"mmcargs=setenv bootargs console=${console},${baudrate} " \
 		"root=${mmcroot}\0" \
 	"loadbootscript=" \
 		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 	"bootscript=echo Running bootscript from mmc ...; " \
 		"source\0" \
 	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 	"mmcboot=echo Booting from mmc ...; " \
 		"run mmcargs; " \
 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 			"if run loadfdt; then " \
 				"bootz ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"if test ${boot_fdt} = try; then " \
 					"bootz; " \
 				"else " \
 					"echo WARN: Cannot load the DT; " \
 				"fi; " \
 			"fi; " \
 		"else " \
 			"bootz; " \
 		"fi;\0" \
 	"netargs=setenv bootargs console=${console},${baudrate} " \
 		"root=/dev/nfs " \
 	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 		"netboot=echo Booting from net ...; " \
 		"run netargs; " \
 		"if test ${ip_dyn} = yes; then " \
 			"setenv get_cmd dhcp; " \
 		"else " \
 			"setenv get_cmd tftp; " \
 		"fi; " \
 		"${get_cmd} ${image}; " \
 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 				"bootz ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"if test ${boot_fdt} = try; then " \
 					"bootz; " \
 				"else " \
 					"echo WARN: Cannot load the DT; " \
 				"fi; " \
 			"fi; " \
 		"else " \
 			"bootz; " \
 		"fi;\0"

 #define CONFIG_BOOTCOMMAND \
 	   "mmc dev ${mmcdev};" \
 	   "mmc dev ${mmcdev}; if mmc rescan; then " \
 		   "if run loadbootscript; then " \
 			   "run bootscript; " \
 		   "else " \
 			   "if run loadimage; then " \
 				   "run mmcboot; " \
 			   "else run netboot; " \
 			   "fi; " \
 		   "fi; " \
 	   "else run netboot; fi"

 #define CONFIG_SYS_MEMTEST_START	0x80000000
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x20000000)

 #define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
 #define CONFIG_SYS_HZ			1000

 #define CONFIG_STACKSIZE		SZ_128K

 /* Physical Memory Map */
 #define CONFIG_NR_DRAM_BANKS		1
 #define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
 #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
 #define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

 #define CONFIG_SYS_INIT_SP_OFFSET \
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

 /* FLASH and environment organization */
 #define CONFIG_SYS_NO_FLASH
 #define CONFIG_ENV_SIZE			SZ_8K
 #define CONFIG_ENV_IS_IN_MMC

 /*
  * If want to use nand, define CONFIG_NAND_MXS and rework board
  * to support nand, since emmc has pin conflicts with nand
  */
 #ifdef CONFIG_NAND_MXS
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_NAND_TRIMFFS

 /* NAND stuff */
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_SYS_NAND_BASE		0x40000000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_ONFI_DETECTION

 /* DMA stuff, needed for GPMI/MXS NAND support */
 #define CONFIG_APBH_DMA
 #define CONFIG_APBH_DMA_BURST
 #define CONFIG_APBH_DMA_BURST8
 #endif

 #define CONFIG_ENV_OFFSET		(8 * SZ_64K)
 #ifdef CONFIG_NAND_MXS
 #define CONFIG_SYS_FSL_USDHC_NUM	1
 #else
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #endif

 #define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC1 */
 #define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
 #define CONFIG_MMCROOT			"/dev/mmcblk0p2"  /* USDHC1 */

 /* USB Configs */
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_HOST_ETHER
 #define CONFIG_USB_ETHER_ASIX
 #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS   0
 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2

 #define CONFIG_IMX_THERMAL

 #define CONFIG_USBD_HS

 #define CONFIG_USB_FUNCTION_MASS_STORAGE

 /* USB Device Firmware Update support */
 #define CONFIG_USB_FUNCTION_DFU
 #define CONFIG_DFU_MMC
 #define CONFIG_DFU_RAM

 #define CONFIG_VIDEO
 #ifdef CONFIG_VIDEO
 #define CONFIG_CFB_CONSOLE
 #define CONFIG_VIDEO_MXS
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_VIDEO_SW_CURSOR
 #define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_SPLASH_SCREEN_ALIGN
 #define CONFIG_CMD_BMP
 #define CONFIG_BMP_16BPP
 #define CONFIG_VIDEO_BMP_RLE8
 #define CONFIG_VIDEO_BMP_LOGO
 #endif

 #ifdef CONFIG_FSL_QSPI
 #define CONFIG_SPI_FLASH
 #define CONFIG_SPI_FLASH_MACRONIX
 #define CONFIG_SPI_FLASH_BAR
 #define CONFIG_SF_DEFAULT_BUS		0
 #define CONFIG_SF_DEFAULT_CS		0
 #define CONFIG_SF_DEFAULT_SPEED		40000000
 #define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
 #define FSL_QSPI_FLASH_NUM		1
 #define FSL_QSPI_FLASH_SIZE		SZ_64M
 #define QSPI0_BASE_ADDR			QSPI1_IPS_BASE_ADDR
 #define QSPI0_AMBA_BASE			QSPI0_ARB_BASE_ADDR
 #endif

 #endif	/* __CONFIG_H */
	/*
	* Copyright (C) 2015 Freescale Semiconductor, Inc.
	*
	* Configuration settings for the Freescale i.MX7D SABRESD board.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __MX7D_SABRESD_CONFIG_H
	#define __MX7D_SABRESD_CONFIG_H

	#include "mx7_common.h"

	#define CONFIG_DBG_MONITOR
	#define PHYS_SDRAM_SIZE SZ_1G

	#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)

	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_BOARD_LATE_INIT

	#define CONFIG_DISPLAY_BOARDINFO

	/* Uncomment to enable secure boot support */
	/* #define CONFIG_SECURE_BOOT */
	#define CONFIG_CSF_SIZE 0x4000

	/* Network */
	#define CONFIG_FEC_MXC
	#define CONFIG_MII
	#define CONFIG_FEC_XCV_TYPE RGMII
	#define CONFIG_ETHPRIME "FEC"
	#define CONFIG_FEC_MXC_PHYADDR 0

	#define CONFIG_PHYLIB
	#define CONFIG_PHY_BROADCOM
	/* ENET1 */
	#define IMX_FEC_BASE ENET_IPS_BASE_ADDR

	/* MMC Config*/
	#define CONFIG_SYS_FSL_ESDHC_ADDR 0

	/* PMIC */
	#define CONFIG_POWER
	#define CONFIG_POWER_I2C
	#define CONFIG_POWER_PFUZE3000
	#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08

	#undef CONFIG_BOOTM_NETBSD
	#undef CONFIG_BOOTM_PLAN9
	#undef CONFIG_BOOTM_RTEMS

	/* I2C configs */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_SPEED 100000

	#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
	#define CONFIG_SYS_MMC_IMG_LOAD_PART 1

	#ifdef CONFIG_IMX_BOOTAUX
	/* Set to QSPI1 A flash at default */
	#define CONFIG_SYS_AUXCORE_BOOTDATA 0x60000000

	#define UPDATE_M4_ENV \
	"m4image=m4_qspi.bin\0" \
	"loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \
	"update_m4_from_sd=" \
	"if sf probe 0:0; then " \
	"if run loadm4image; then " \
	"setexpr fw_sz ${filesize} + 0xffff; " \
	"setexpr fw_sz ${fw_sz} / 0x10000; " \
	"setexpr fw_sz ${fw_sz} * 0x10000; " \
	"sf erase 0x0 ${fw_sz}; " \
	"sf write ${loadaddr} 0x0 ${filesize}; " \
	"fi; " \
	"fi\0" \
	"m4boot=sf probe 0:0; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"
	#else
	#define UPDATE_M4_ENV ""
	#endif

	#define CONFIG_MFG_ENV_SETTINGS \
	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
	"rdinit=/linuxrc " \
	"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
	"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
	"g_mass_storage.iSerialNumber=\"\" "\
	"clk_ignore_unused "\
	"\0" \
	"initrd_addr=0x83800000\0" \
	"initrd_high=0xffffffff\0" \
	"bootcmd_mfg=run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \

	#define CONFIG_DFU_ENV_SETTINGS \
	"dfu_alt_info=image raw 0 0x800000;"\
	"u-boot raw 0 0x4000;"\
	"bootimg part 0 1;"\
	"rootfs part 0 2\0" \

	#define CONFIG_EXTRA_ENV_SETTINGS \
	UPDATE_M4_ENV \
	CONFIG_MFG_ENV_SETTINGS \
	CONFIG_DFU_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=zImage\0" \
	"console=ttymxc0\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"fdt_file=imx7d-sdb.dtb\0" \
	"fdt_addr=0x83000000\0" \
	"boot_fdt=try\0" \
	"ip_dyn=yes\0" \
	"videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcautodetect=yes\0" \
	"mmcargs=setenv bootargs console=${console},${baudrate} " \
	"root=${mmcroot}\0" \
	"loadbootscript=" \
	"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
	"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
	"run mmcargs; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if run loadfdt; then " \
	"bootz ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"if test ${boot_fdt} = try; then " \
	"bootz; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"fi; " \
	"else " \
	"bootz; " \
	"fi;\0" \
	"netargs=setenv bootargs console=${console},${baudrate} " \
	"root=/dev/nfs " \
	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
	"run netargs; " \
	"if test ${ip_dyn} = yes; then " \
	"setenv get_cmd dhcp; " \
	"else " \
	"setenv get_cmd tftp; " \
	"fi; " \
	"${get_cmd} ${image}; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
	"bootz ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"if test ${boot_fdt} = try; then " \
	"bootz; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"fi; " \
	"else " \
	"bootz; " \
	"fi;\0"

	#define CONFIG_BOOTCOMMAND \
	"mmc dev ${mmcdev};" \
	"mmc dev ${mmcdev}; if mmc rescan; then " \
	"if run loadbootscript; then " \
	"run bootscript; " \
	"else " \
	"if run loadimage; then " \
	"run mmcboot; " \
	"else run netboot; " \
	"fi; " \
	"fi; " \
	"else run netboot; fi"

	#define CONFIG_SYS_MEMTEST_START 0x80000000
	#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x20000000)

	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
	#define CONFIG_SYS_HZ 1000

	#define CONFIG_STACKSIZE SZ_128K

	/* Physical Memory Map */
	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR

	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE

	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	/* FLASH and environment organization */
	#define CONFIG_SYS_NO_FLASH
	#define CONFIG_ENV_SIZE SZ_8K
	#define CONFIG_ENV_IS_IN_MMC

	/*
	* If want to use nand, define CONFIG_NAND_MXS and rework board
	* to support nand, since emmc has pin conflicts with nand
	*/
	#ifdef CONFIG_NAND_MXS
	#define CONFIG_CMD_NAND
	#define CONFIG_CMD_NAND_TRIMFFS

	/* NAND stuff */
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_BASE 0x40000000
	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	#define CONFIG_SYS_NAND_ONFI_DETECTION

	/* DMA stuff, needed for GPMI/MXS NAND support */
	#define CONFIG_APBH_DMA
	#define CONFIG_APBH_DMA_BURST
	#define CONFIG_APBH_DMA_BURST8
	#endif

	#define CONFIG_ENV_OFFSET (8 * SZ_64K)
	#ifdef CONFIG_NAND_MXS
	#define CONFIG_SYS_FSL_USDHC_NUM 1
	#else
	#define CONFIG_SYS_FSL_USDHC_NUM 2
	#endif

	#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC1 */
	#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
	#define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC1 */

	/* USB Configs */
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	#define CONFIG_USB_HOST_ETHER
	#define CONFIG_USB_ETHER_ASIX
	#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI \| PORT_PTS_PTW)
	#define CONFIG_MXC_USB_FLAGS 0
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2

	#define CONFIG_IMX_THERMAL

	#define CONFIG_USBD_HS

	#define CONFIG_USB_FUNCTION_MASS_STORAGE

	/* USB Device Firmware Update support */
	#define CONFIG_USB_FUNCTION_DFU
	#define CONFIG_DFU_MMC
	#define CONFIG_DFU_RAM

	#define CONFIG_VIDEO
	#ifdef CONFIG_VIDEO
	#define CONFIG_CFB_CONSOLE
	#define CONFIG_VIDEO_MXS
	#define CONFIG_VIDEO_LOGO
	#define CONFIG_VIDEO_SW_CURSOR
	#define CONFIG_VGA_AS_SINGLE_DEVICE
	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
	#define CONFIG_SPLASH_SCREEN
	#define CONFIG_SPLASH_SCREEN_ALIGN
	#define CONFIG_CMD_BMP
	#define CONFIG_BMP_16BPP
	#define CONFIG_VIDEO_BMP_RLE8
	#define CONFIG_VIDEO_BMP_LOGO
	#endif

	#ifdef CONFIG_FSL_QSPI
	#define CONFIG_SPI_FLASH
	#define CONFIG_SPI_FLASH_MACRONIX
	#define CONFIG_SPI_FLASH_BAR
	#define CONFIG_SF_DEFAULT_BUS 0
	#define CONFIG_SF_DEFAULT_CS 0
	#define CONFIG_SF_DEFAULT_SPEED 40000000
	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
	#define FSL_QSPI_FLASH_NUM 1
	#define FSL_QSPI_FLASH_SIZE SZ_64M
	#define QSPI0_BASE_ADDR QSPI1_IPS_BASE_ADDR
	#define QSPI0_AMBA_BASE QSPI0_ARB_BASE_ADDR
	#endif

	#endif /* __CONFIG_H */