drivers/net/fm/fm.c - github/trini/u-boot - Gitiles

 /*
  * Copyright 2009-2011 Freescale Semiconductor, Inc.
  *	Dave Liu <daveliu@freescale.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
 #include <common.h>
 #include <malloc.h>
 #include <asm/io.h>
 #include <asm/errno.h>

 #include "fm.h"
 #include <fsl_qe.h>		/* For struct qe_firmware */

 #ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND
 #include <nand.h>
 #elif defined(CONFIG_SYS_QE_FW_IN_SPIFLASH)
 #include <spi_flash.h>
 #elif defined(CONFIG_SYS_QE_FMAN_FW_IN_MMC)
 #include <mmc.h>
 #endif

 struct fm_muram muram[CONFIG_SYS_NUM_FMAN];

 void *fm_muram_base(int fm_idx)
 {
 	return muram[fm_idx].base;
 }

 void *fm_muram_alloc(int fm_idx, size_t size, ulong align)
 {
 	void *ret;
 	ulong align_mask;
 	size_t off;
 	void *save;

 	align_mask = align - 1;
 	save = muram[fm_idx].alloc;

 	off = (ulong)save & align_mask;
 	if (off != 0)
 		muram[fm_idx].alloc += (align - off);
 	off = size & align_mask;
 	if (off != 0)
 		size += (align - off);
 	if ((muram[fm_idx].alloc + size) >= muram[fm_idx].top) {
 		muram[fm_idx].alloc = save;
 		printf("%s: run out of ram.\n", __func__);
 		return NULL;
 	}

 	ret = muram[fm_idx].alloc;
 	muram[fm_idx].alloc += size;
 	memset((void *)ret, 0, size);

 	return ret;
 }

 static void fm_init_muram(int fm_idx, void *reg)
 {
 	void *base = reg;

 	muram[fm_idx].base = base;
 	muram[fm_idx].size = CONFIG_SYS_FM_MURAM_SIZE;
 	muram[fm_idx].alloc = base + FM_MURAM_RES_SIZE;
 	muram[fm_idx].top = base + CONFIG_SYS_FM_MURAM_SIZE;
 }

 /*
  * fm_upload_ucode - Fman microcode upload worker function
  *
  * This function does the actual uploading of an Fman microcode
  * to an Fman.
  */
 static void fm_upload_ucode(int fm_idx, struct fm_imem *imem,
 			    u32 *ucode, unsigned int size)
 {
 	unsigned int i;
 	unsigned int timeout = 1000000;

 	/* enable address auto increase */
 	out_be32(&imem->iadd, IRAM_IADD_AIE);
 	/* write microcode to IRAM */
 	for (i = 0; i < size / 4; i++)
 		out_be32(&imem->idata, (be32_to_cpu(ucode[i])));

 	/* verify if the writing is over */
 	out_be32(&imem->iadd, 0);
 	while ((in_be32(&imem->idata) != be32_to_cpu(ucode[0])) && --timeout)
 		;
 	if (!timeout)
 		printf("Fman%u: microcode upload timeout\n", fm_idx + 1);

 	/* enable microcode from IRAM */
 	out_be32(&imem->iready, IRAM_READY);
 }

 /*
  * Upload an Fman firmware
  *
  * This function is similar to qe_upload_firmware(), exception that it uploads
  * a microcode to the Fman instead of the QE.
  *
  * Because the process for uploading a microcode to the Fman is similar for
  * that of the QE, the QE firmware binary format is used for Fman microcode.
  * It should be possible to unify these two functions, but for now we keep them
  * separate.
  */
 static int fman_upload_firmware(int fm_idx,
 				struct fm_imem *fm_imem,
 				const struct qe_firmware *firmware)
 {
 	unsigned int i;
 	u32 crc;
 	size_t calc_size = sizeof(struct qe_firmware);
 	size_t length;
 	const struct qe_header *hdr;

 	if (!firmware) {
 		printf("Fman%u: Invalid address for firmware\n", fm_idx + 1);
 		return -EINVAL;
 	}

 	hdr = &firmware->header;
 	length = be32_to_cpu(hdr->length);

 	/* Check the magic */
 	if ((hdr->magic[0] != 'Q') || (hdr->magic[1] != 'E') ||
 		(hdr->magic[2] != 'F')) {
 		printf("Fman%u: Data at %p is not a firmware\n", fm_idx + 1,
 		       firmware);
 		return -EPERM;
 	}

 	/* Check the version */
 	if (hdr->version != 1) {
 		printf("Fman%u: Unsupported firmware version %u\n", fm_idx + 1,
 		       hdr->version);
 		return -EPERM;
 	}

 	/* Validate some of the fields */
 	if ((firmware->count != 1)) {
 		printf("Fman%u: Invalid data in firmware header\n", fm_idx + 1);
 		return -EINVAL;
 	}

 	/* Validate the length and check if there's a CRC */
 	calc_size += (firmware->count - 1) * sizeof(struct qe_microcode);

 	for (i = 0; i < firmware->count; i++)
 		/*
 		 * For situations where the second RISC uses the same microcode
 		 * as the first, the 'code_offset' and 'count' fields will be
 		 * zero, so it's okay to add those.
 		 */
 		calc_size += sizeof(u32) *
 			be32_to_cpu(firmware->microcode[i].count);

 	/* Validate the length */
 	if (length != calc_size + sizeof(u32)) {
 		printf("Fman%u: Invalid length in firmware header\n",
 		       fm_idx + 1);
 		return -EPERM;
 	}

 	/*
 	 * Validate the CRC.  We would normally call crc32_no_comp(), but that
 	 * function isn't available unless you turn on JFFS support.
 	 */
 	crc = be32_to_cpu(*(u32 *)((void *)firmware + calc_size));
 	if (crc != (crc32(-1, (const void *)firmware, calc_size) ^ -1)) {
 		printf("Fman%u: Firmware CRC is invalid\n", fm_idx + 1);
 		return -EIO;
 	}

 	/* Loop through each microcode. */
 	for (i = 0; i < firmware->count; i++) {
 		const struct qe_microcode *ucode = &firmware->microcode[i];

 		/* Upload a microcode if it's present */
 		if (be32_to_cpu(ucode->code_offset)) {
 			u32 ucode_size;
 			u32 *code;
 			printf("Fman%u: Uploading microcode version %u.%u.%u\n",
 			       fm_idx + 1, ucode->major, ucode->minor,
 			       ucode->revision);
 			code = (void *)firmware +
 			       be32_to_cpu(ucode->code_offset);
 			ucode_size = sizeof(u32) * be32_to_cpu(ucode->count);
 			fm_upload_ucode(fm_idx, fm_imem, code, ucode_size);
 		}
 	}

 	return 0;
 }

 static u32 fm_assign_risc(int port_id)
 {
 	u32 risc_sel, val;
 	risc_sel = (port_id & 0x1) ? FMFPPRC_RISC2 : FMFPPRC_RISC1;
 	val = (port_id << FMFPPRC_PORTID_SHIFT) & FMFPPRC_PORTID_MASK;
 	val |= ((risc_sel << FMFPPRC_ORA_SHIFT) | risc_sel);

 	return val;
 }

 static void fm_init_fpm(struct fm_fpm *fpm)
 {
 	int i, port_id;
 	u32 val;

 	setbits_be32(&fpm->fmfpee, FMFPEE_EHM | FMFPEE_UEC |
 				   FMFPEE_CER | FMFPEE_DER);

 	/* IM mode, each even port ID to RISC#1, each odd port ID to RISC#2 */

 	/* offline/parser port */
 	for (i = 0; i < MAX_NUM_OH_PORT; i++) {
 		port_id = OH_PORT_ID_BASE + i;
 		val = fm_assign_risc(port_id);
 		out_be32(&fpm->fpmprc, val);
 	}
 	/* Rx 1G port */
 	for (i = 0; i < MAX_NUM_RX_PORT_1G; i++) {
 		port_id = RX_PORT_1G_BASE + i;
 		val = fm_assign_risc(port_id);
 		out_be32(&fpm->fpmprc, val);
 	}
 	/* Tx 1G port */
 	for (i = 0; i < MAX_NUM_TX_PORT_1G; i++) {
 		port_id = TX_PORT_1G_BASE + i;
 		val = fm_assign_risc(port_id);
 		out_be32(&fpm->fpmprc, val);
 	}
 	/* Rx 10G port */
 	port_id = RX_PORT_10G_BASE;
 	val = fm_assign_risc(port_id);
 	out_be32(&fpm->fpmprc, val);
 	/* Tx 10G port */
 	port_id = TX_PORT_10G_BASE;
 	val = fm_assign_risc(port_id);
 	out_be32(&fpm->fpmprc, val);

 	/* disable the dispatch limit in IM case */
 	out_be32(&fpm->fpmflc, FMFP_FLC_DISP_LIM_NONE);
 	/* clear events */
 	out_be32(&fpm->fmfpee, FMFPEE_CLEAR_EVENT);

 	/* clear risc events */
 	for (i = 0; i < 4; i++)
 		out_be32(&fpm->fpmcev[i], 0xffffffff);

 	/* clear error */
 	out_be32(&fpm->fpmrcr, FMFP_RCR_MDEC | FMFP_RCR_IDEC);
 }

 static int fm_init_bmi(int fm_idx, struct fm_bmi_common *bmi)
 {
 	int blk, i, port_id;
 	u32 val;
 	size_t offset;
 	void *base;

 	/* alloc free buffer pool in MURAM */
 	base = fm_muram_alloc(fm_idx, FM_FREE_POOL_SIZE, FM_FREE_POOL_ALIGN);
 	if (!base) {
 		printf("%s: no muram for free buffer pool\n", __func__);
 		return -ENOMEM;
 	}
 	offset = base - fm_muram_base(fm_idx);

 	/* Need 128KB total free buffer pool size */
 	val = offset / 256;
 	blk = FM_FREE_POOL_SIZE / 256;
 	/* in IM, we must not begin from offset 0 in MURAM */
 	val |= ((blk - 1) << FMBM_CFG1_FBPS_SHIFT);
 	out_be32(&bmi->fmbm_cfg1, val);

 	/* disable all BMI interrupt */
 	out_be32(&bmi->fmbm_ier, FMBM_IER_DISABLE_ALL);

 	/* clear all events */
 	out_be32(&bmi->fmbm_ievr, FMBM_IEVR_CLEAR_ALL);

 	/*
 	 * set port parameters - FMBM_PP_x
 	 * max tasks 10G Rx/Tx=12, 1G Rx/Tx 4, others is 1
 	 * max dma 10G Rx/Tx=3, others is 1
 	 * set port FIFO size - FMBM_PFS_x
 	 * 4KB for all Rx and Tx ports
 	 */
 	/* offline/parser port */
 	for (i = 0; i < MAX_NUM_OH_PORT; i++) {
 		port_id = OH_PORT_ID_BASE + i - 1;
 		/* max tasks=1, max dma=1, no extra */
 		out_be32(&bmi->fmbm_pp[port_id], 0);
 		/* port FIFO size - 256 bytes, no extra */
 		out_be32(&bmi->fmbm_pfs[port_id], 0);
 	}
 	/* Rx 1G port */
 	for (i = 0; i < MAX_NUM_RX_PORT_1G; i++) {
 		port_id = RX_PORT_1G_BASE + i - 1;
 		/* max tasks=4, max dma=1, no extra */
 		out_be32(&bmi->fmbm_pp[port_id], FMBM_PP_MXT(4));
 		/* FIFO size - 4KB, no extra */
 		out_be32(&bmi->fmbm_pfs[port_id], FMBM_PFS_IFSZ(0xf));
 	}
 	/* Tx 1G port FIFO size - 4KB, no extra */
 	for (i = 0; i < MAX_NUM_TX_PORT_1G; i++) {
 		port_id = TX_PORT_1G_BASE + i - 1;
 		/* max tasks=4, max dma=1, no extra */
 		out_be32(&bmi->fmbm_pp[port_id], FMBM_PP_MXT(4));
 		/* FIFO size - 4KB, no extra */
 		out_be32(&bmi->fmbm_pfs[port_id], FMBM_PFS_IFSZ(0xf));
 	}
 	/* Rx 10G port */
 	port_id = RX_PORT_10G_BASE - 1;
 	/* max tasks=12, max dma=3, no extra */
 	out_be32(&bmi->fmbm_pp[port_id], FMBM_PP_MXT(12) | FMBM_PP_MXD(3));
 	/* FIFO size - 4KB, no extra */
 	out_be32(&bmi->fmbm_pfs[port_id], FMBM_PFS_IFSZ(0xf));

 	/* Tx 10G port */
 	port_id = TX_PORT_10G_BASE - 1;
 	/* max tasks=12, max dma=3, no extra */
 	out_be32(&bmi->fmbm_pp[port_id], FMBM_PP_MXT(12) | FMBM_PP_MXD(3));
 	/* FIFO size - 4KB, no extra */
 	out_be32(&bmi->fmbm_pfs[port_id], FMBM_PFS_IFSZ(0xf));

 	/* initialize internal buffers data base (linked list) */
 	out_be32(&bmi->fmbm_init, FMBM_INIT_START);

 	return 0;
 }

 static void fm_init_qmi(struct fm_qmi_common *qmi)
 {
 	/* disable all error interrupts */
 	out_be32(&qmi->fmqm_eien, FMQM_EIEN_DISABLE_ALL);
 	/* clear all error events */
 	out_be32(&qmi->fmqm_eie, FMQM_EIE_CLEAR_ALL);

 	/* disable all interrupts */
 	out_be32(&qmi->fmqm_ien, FMQM_IEN_DISABLE_ALL);
 	/* clear all interrupts */
 	out_be32(&qmi->fmqm_ie, FMQM_IE_CLEAR_ALL);
 }

 /* Init common part of FM, index is fm num# like fm as above */
 int fm_init_common(int index, struct ccsr_fman *reg)
 {
 	int rc;
 #if defined(CONFIG_SYS_QE_FMAN_FW_IN_NOR)
 	void *addr = (void *)CONFIG_SYS_FMAN_FW_ADDR;
 #elif defined(CONFIG_SYS_QE_FMAN_FW_IN_NAND)
 	size_t fw_length = CONFIG_SYS_QE_FMAN_FW_LENGTH;
 	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);

 	rc = nand_read(nand_info[0], (loff_t)CONFIG_SYS_FMAN_FW_ADDR,
 		       &fw_length, (u_char *)addr);
 	if (rc == -EUCLEAN) {
 		printf("NAND read of FMAN firmware at offset 0x%x failed %d\n",
 			CONFIG_SYS_FMAN_FW_ADDR, rc);
 	}
 #elif defined(CONFIG_SYS_QE_FW_IN_SPIFLASH)
 	struct spi_flash *ucode_flash;
 	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
 	int ret = 0;

 	ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
 			CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
 	if (!ucode_flash)
 		printf("SF: probe for ucode failed\n");
 	else {
 		ret = spi_flash_read(ucode_flash, CONFIG_SYS_FMAN_FW_ADDR,
 				CONFIG_SYS_QE_FMAN_FW_LENGTH, addr);
 		if (ret)
 			printf("SF: read for ucode failed\n");
 		spi_flash_free(ucode_flash);
 	}
 #elif defined(CONFIG_SYS_QE_FMAN_FW_IN_MMC)
 	int dev = CONFIG_SYS_MMC_ENV_DEV;
 	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
 	u32 cnt = CONFIG_SYS_QE_FMAN_FW_LENGTH / 512;
 	u32 blk = CONFIG_SYS_FMAN_FW_ADDR / 512;
 	struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);

 	if (!mmc)
 		printf("\nMMC cannot find device for ucode\n");
 	else {
 		printf("\nMMC read: dev # %u, block # %u, count %u ...\n",
 				dev, blk, cnt);
 		mmc_init(mmc);
 		(void)mmc->block_dev.block_read(&mmc->block_dev, blk, cnt,
 						addr);
 		/* flush cache after read */
 		flush_cache((ulong)addr, cnt * 512);
 	}
 #elif defined(CONFIG_SYS_QE_FMAN_FW_IN_REMOTE)
 	void *addr = (void *)CONFIG_SYS_FMAN_FW_ADDR;
 #else
 	void *addr = NULL;
 #endif

 	/* Upload the Fman microcode if it's present */
 	rc = fman_upload_firmware(index, &reg->fm_imem, addr);
 	if (rc)
 		return rc;
 	setenv_addr("fman_ucode", addr);

 	fm_init_muram(index, &reg->muram);
 	fm_init_qmi(&reg->fm_qmi_common);
 	fm_init_fpm(&reg->fm_fpm);

 	/* clear DMA status */
 	setbits_be32(&reg->fm_dma.fmdmsr, FMDMSR_CLEAR_ALL);

 	/* set DMA mode */
 	setbits_be32(&reg->fm_dma.fmdmmr, FMDMMR_SBER);

 	return fm_init_bmi(index, &reg->fm_bmi_common);
 }
	/*
	* Copyright 2009-2011 Freescale Semiconductor, Inc.
	* Dave Liu <daveliu@freescale.com>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/
	#include <common.h>
	#include <malloc.h>
	#include <asm/io.h>
	#include <asm/errno.h>

	#include "fm.h"
	#include <fsl_qe.h> /* For struct qe_firmware */

	#ifdef CONFIG_SYS_QE_FMAN_FW_IN_NAND
	#include <nand.h>
	#elif defined(CONFIG_SYS_QE_FW_IN_SPIFLASH)
	#include <spi_flash.h>
	#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_MMC)
	#include <mmc.h>
	#endif

	struct fm_muram muram[CONFIG_SYS_NUM_FMAN];

	void *fm_muram_base(int fm_idx)
	{
	return muram[fm_idx].base;
	}

	void *fm_muram_alloc(int fm_idx, size_t size, ulong align)
	{
	void *ret;
	ulong align_mask;
	size_t off;
	void *save;

	align_mask = align - 1;
	save = muram[fm_idx].alloc;

	off = (ulong)save & align_mask;
	if (off != 0)
	muram[fm_idx].alloc += (align - off);
	off = size & align_mask;
	if (off != 0)
	size += (align - off);
	if ((muram[fm_idx].alloc + size) >= muram[fm_idx].top) {
	muram[fm_idx].alloc = save;
	printf("%s: run out of ram.\n", __func__);
	return NULL;
	}

	ret = muram[fm_idx].alloc;
	muram[fm_idx].alloc += size;
	memset((void *)ret, 0, size);

	return ret;
	}

	static void fm_init_muram(int fm_idx, void *reg)
	{
	void *base = reg;

	muram[fm_idx].base = base;
	muram[fm_idx].size = CONFIG_SYS_FM_MURAM_SIZE;
	muram[fm_idx].alloc = base + FM_MURAM_RES_SIZE;
	muram[fm_idx].top = base + CONFIG_SYS_FM_MURAM_SIZE;
	}

	/*
	* fm_upload_ucode - Fman microcode upload worker function
	*
	* This function does the actual uploading of an Fman microcode
	* to an Fman.
	*/
	static void fm_upload_ucode(int fm_idx, struct fm_imem *imem,
	u32 *ucode, unsigned int size)
	{
	unsigned int i;
	unsigned int timeout = 1000000;

	/* enable address auto increase */
	out_be32(&imem->iadd, IRAM_IADD_AIE);
	/* write microcode to IRAM */
	for (i = 0; i < size / 4; i++)
	out_be32(&imem->idata, (be32_to_cpu(ucode[i])));

	/* verify if the writing is over */
	out_be32(&imem->iadd, 0);
	while ((in_be32(&imem->idata) != be32_to_cpu(ucode[0])) && --timeout)
	;
	if (!timeout)
	printf("Fman%u: microcode upload timeout\n", fm_idx + 1);

	/* enable microcode from IRAM */
	out_be32(&imem->iready, IRAM_READY);
	}

	/*
	* Upload an Fman firmware
	*
	* This function is similar to qe_upload_firmware(), exception that it uploads
	* a microcode to the Fman instead of the QE.
	*
	* Because the process for uploading a microcode to the Fman is similar for
	* that of the QE, the QE firmware binary format is used for Fman microcode.
	* It should be possible to unify these two functions, but for now we keep them
	* separate.
	*/
	static int fman_upload_firmware(int fm_idx,
	struct fm_imem *fm_imem,
	const struct qe_firmware *firmware)
	{
	unsigned int i;
	u32 crc;
	size_t calc_size = sizeof(struct qe_firmware);
	size_t length;
	const struct qe_header *hdr;

	if (!firmware) {
	printf("Fman%u: Invalid address for firmware\n", fm_idx + 1);
	return -EINVAL;
	}

	hdr = &firmware->header;
	length = be32_to_cpu(hdr->length);

	/* Check the magic */
	if ((hdr->magic[0] != 'Q') \|\| (hdr->magic[1] != 'E') \|\|
	(hdr->magic[2] != 'F')) {
	printf("Fman%u: Data at %p is not a firmware\n", fm_idx + 1,
	firmware);
	return -EPERM;
	}

	/* Check the version */
	if (hdr->version != 1) {
	printf("Fman%u: Unsupported firmware version %u\n", fm_idx + 1,
	hdr->version);
	return -EPERM;
	}

	/* Validate some of the fields */
	if ((firmware->count != 1)) {
	printf("Fman%u: Invalid data in firmware header\n", fm_idx + 1);
	return -EINVAL;
	}

	/* Validate the length and check if there's a CRC */
	calc_size += (firmware->count - 1) * sizeof(struct qe_microcode);

	for (i = 0; i < firmware->count; i++)
	/*
	* For situations where the second RISC uses the same microcode
	* as the first, the 'code_offset' and 'count' fields will be
	* zero, so it's okay to add those.
	*/
	calc_size += sizeof(u32) *
	be32_to_cpu(firmware->microcode[i].count);

	/* Validate the length */
	if (length != calc_size + sizeof(u32)) {
	printf("Fman%u: Invalid length in firmware header\n",
	fm_idx + 1);
	return -EPERM;
	}

	/*
	* Validate the CRC. We would normally call crc32_no_comp(), but that
	* function isn't available unless you turn on JFFS support.
	*/
	crc = be32_to_cpu((u32 )((void *)firmware + calc_size));
	if (crc != (crc32(-1, (const void *)firmware, calc_size) ^ -1)) {
	printf("Fman%u: Firmware CRC is invalid\n", fm_idx + 1);
	return -EIO;
	}

	/* Loop through each microcode. */
	for (i = 0; i < firmware->count; i++) {
	const struct qe_microcode *ucode = &firmware->microcode[i];

	/* Upload a microcode if it's present */
	if (be32_to_cpu(ucode->code_offset)) {
	u32 ucode_size;
	u32 *code;
	printf("Fman%u: Uploading microcode version %u.%u.%u\n",
	fm_idx + 1, ucode->major, ucode->minor,
	ucode->revision);
	code = (void *)firmware +
	be32_to_cpu(ucode->code_offset);
	ucode_size = sizeof(u32) * be32_to_cpu(ucode->count);
	fm_upload_ucode(fm_idx, fm_imem, code, ucode_size);
	}
	}

	return 0;
	}

	static u32 fm_assign_risc(int port_id)
	{
	u32 risc_sel, val;
	risc_sel = (port_id & 0x1) ? FMFPPRC_RISC2 : FMFPPRC_RISC1;
	val = (port_id << FMFPPRC_PORTID_SHIFT) & FMFPPRC_PORTID_MASK;
	val \|= ((risc_sel << FMFPPRC_ORA_SHIFT) \| risc_sel);

	return val;
	}

	static void fm_init_fpm(struct fm_fpm *fpm)
	{
	int i, port_id;
	u32 val;

	setbits_be32(&fpm->fmfpee, FMFPEE_EHM \| FMFPEE_UEC \|
	FMFPEE_CER \| FMFPEE_DER);

	/* IM mode, each even port ID to RISC#1, each odd port ID to RISC#2 */

	/* offline/parser port */
	for (i = 0; i < MAX_NUM_OH_PORT; i++) {
	port_id = OH_PORT_ID_BASE + i;
	val = fm_assign_risc(port_id);
	out_be32(&fpm->fpmprc, val);
	}
	/* Rx 1G port */
	for (i = 0; i < MAX_NUM_RX_PORT_1G; i++) {
	port_id = RX_PORT_1G_BASE + i;
	val = fm_assign_risc(port_id);
	out_be32(&fpm->fpmprc, val);
	}
	/* Tx 1G port */
	for (i = 0; i < MAX_NUM_TX_PORT_1G; i++) {
	port_id = TX_PORT_1G_BASE + i;
	val = fm_assign_risc(port_id);
	out_be32(&fpm->fpmprc, val);
	}
	/* Rx 10G port */
	port_id = RX_PORT_10G_BASE;
	val = fm_assign_risc(port_id);
	out_be32(&fpm->fpmprc, val);
	/* Tx 10G port */
	port_id = TX_PORT_10G_BASE;
	val = fm_assign_risc(port_id);
	out_be32(&fpm->fpmprc, val);

	/* disable the dispatch limit in IM case */
	out_be32(&fpm->fpmflc, FMFP_FLC_DISP_LIM_NONE);
	/* clear events */
	out_be32(&fpm->fmfpee, FMFPEE_CLEAR_EVENT);

	/* clear risc events */
	for (i = 0; i < 4; i++)
	out_be32(&fpm->fpmcev[i], 0xffffffff);

	/* clear error */
	out_be32(&fpm->fpmrcr, FMFP_RCR_MDEC \| FMFP_RCR_IDEC);
	}

	static int fm_init_bmi(int fm_idx, struct fm_bmi_common *bmi)
	{
	int blk, i, port_id;
	u32 val;
	size_t offset;
	void *base;

	/* alloc free buffer pool in MURAM */
	base = fm_muram_alloc(fm_idx, FM_FREE_POOL_SIZE, FM_FREE_POOL_ALIGN);
	if (!base) {
	printf("%s: no muram for free buffer pool\n", __func__);
	return -ENOMEM;
	}
	offset = base - fm_muram_base(fm_idx);

	/* Need 128KB total free buffer pool size */
	val = offset / 256;
	blk = FM_FREE_POOL_SIZE / 256;
	/* in IM, we must not begin from offset 0 in MURAM */
	val \|= ((blk - 1) << FMBM_CFG1_FBPS_SHIFT);
	out_be32(&bmi->fmbm_cfg1, val);

	/* disable all BMI interrupt */
	out_be32(&bmi->fmbm_ier, FMBM_IER_DISABLE_ALL);

	/* clear all events */
	out_be32(&bmi->fmbm_ievr, FMBM_IEVR_CLEAR_ALL);

	/*
	* set port parameters - FMBM_PP_x
	* max tasks 10G Rx/Tx=12, 1G Rx/Tx 4, others is 1
	* max dma 10G Rx/Tx=3, others is 1
	* set port FIFO size - FMBM_PFS_x
	* 4KB for all Rx and Tx ports
	*/
	/* offline/parser port */
	for (i = 0; i < MAX_NUM_OH_PORT; i++) {
	port_id = OH_PORT_ID_BASE + i - 1;
	/* max tasks=1, max dma=1, no extra */
	out_be32(&bmi->fmbm_pp[port_id], 0);
	/* port FIFO size - 256 bytes, no extra */
	out_be32(&bmi->fmbm_pfs[port_id], 0);
	}
	/* Rx 1G port */
	for (i = 0; i < MAX_NUM_RX_PORT_1G; i++) {
	port_id = RX_PORT_1G_BASE + i - 1;
	/* max tasks=4, max dma=1, no extra */
	out_be32(&bmi->fmbm_pp[port_id], FMBM_PP_MXT(4));
	/* FIFO size - 4KB, no extra */
	out_be32(&bmi->fmbm_pfs[port_id], FMBM_PFS_IFSZ(0xf));
	}
	/* Tx 1G port FIFO size - 4KB, no extra */
	for (i = 0; i < MAX_NUM_TX_PORT_1G; i++) {
	port_id = TX_PORT_1G_BASE + i - 1;
	/* max tasks=4, max dma=1, no extra */
	out_be32(&bmi->fmbm_pp[port_id], FMBM_PP_MXT(4));
	/* FIFO size - 4KB, no extra */
	out_be32(&bmi->fmbm_pfs[port_id], FMBM_PFS_IFSZ(0xf));
	}
	/* Rx 10G port */
	port_id = RX_PORT_10G_BASE - 1;
	/* max tasks=12, max dma=3, no extra */
	out_be32(&bmi->fmbm_pp[port_id], FMBM_PP_MXT(12) \| FMBM_PP_MXD(3));
	/* FIFO size - 4KB, no extra */
	out_be32(&bmi->fmbm_pfs[port_id], FMBM_PFS_IFSZ(0xf));

	/* Tx 10G port */
	port_id = TX_PORT_10G_BASE - 1;
	/* max tasks=12, max dma=3, no extra */
	out_be32(&bmi->fmbm_pp[port_id], FMBM_PP_MXT(12) \| FMBM_PP_MXD(3));
	/* FIFO size - 4KB, no extra */
	out_be32(&bmi->fmbm_pfs[port_id], FMBM_PFS_IFSZ(0xf));

	/* initialize internal buffers data base (linked list) */
	out_be32(&bmi->fmbm_init, FMBM_INIT_START);

	return 0;
	}

	static void fm_init_qmi(struct fm_qmi_common *qmi)
	{
	/* disable all error interrupts */
	out_be32(&qmi->fmqm_eien, FMQM_EIEN_DISABLE_ALL);
	/* clear all error events */
	out_be32(&qmi->fmqm_eie, FMQM_EIE_CLEAR_ALL);

	/* disable all interrupts */
	out_be32(&qmi->fmqm_ien, FMQM_IEN_DISABLE_ALL);
	/* clear all interrupts */
	out_be32(&qmi->fmqm_ie, FMQM_IE_CLEAR_ALL);
	}

	/* Init common part of FM, index is fm num# like fm as above */
	int fm_init_common(int index, struct ccsr_fman *reg)
	{
	int rc;
	#if defined(CONFIG_SYS_QE_FMAN_FW_IN_NOR)
	void addr = (void )CONFIG_SYS_FMAN_FW_ADDR;
	#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_NAND)
	size_t fw_length = CONFIG_SYS_QE_FMAN_FW_LENGTH;
	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);

	rc = nand_read(nand_info[0], (loff_t)CONFIG_SYS_FMAN_FW_ADDR,
	&fw_length, (u_char *)addr);
	if (rc == -EUCLEAN) {
	printf("NAND read of FMAN firmware at offset 0x%x failed %d\n",
	CONFIG_SYS_FMAN_FW_ADDR, rc);
	}
	#elif defined(CONFIG_SYS_QE_FW_IN_SPIFLASH)
	struct spi_flash *ucode_flash;
	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
	int ret = 0;

	ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
	CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
	if (!ucode_flash)
	printf("SF: probe for ucode failed\n");
	else {
	ret = spi_flash_read(ucode_flash, CONFIG_SYS_FMAN_FW_ADDR,
	CONFIG_SYS_QE_FMAN_FW_LENGTH, addr);
	if (ret)
	printf("SF: read for ucode failed\n");
	spi_flash_free(ucode_flash);
	}
	#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_MMC)
	int dev = CONFIG_SYS_MMC_ENV_DEV;
	void *addr = malloc(CONFIG_SYS_QE_FMAN_FW_LENGTH);
	u32 cnt = CONFIG_SYS_QE_FMAN_FW_LENGTH / 512;
	u32 blk = CONFIG_SYS_FMAN_FW_ADDR / 512;
	struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);

	if (!mmc)
	printf("\nMMC cannot find device for ucode\n");
	else {
	printf("\nMMC read: dev # %u, block # %u, count %u ...\n",
	dev, blk, cnt);
	mmc_init(mmc);
	(void)mmc->block_dev.block_read(&mmc->block_dev, blk, cnt,
	addr);
	/* flush cache after read */
	flush_cache((ulong)addr, cnt * 512);
	}
	#elif defined(CONFIG_SYS_QE_FMAN_FW_IN_REMOTE)
	void addr = (void )CONFIG_SYS_FMAN_FW_ADDR;
	#else
	void *addr = NULL;
	#endif

	/* Upload the Fman microcode if it's present */
	rc = fman_upload_firmware(index, &reg->fm_imem, addr);
	if (rc)
	return rc;
	setenv_addr("fman_ucode", addr);

	fm_init_muram(index, &reg->muram);
	fm_init_qmi(&reg->fm_qmi_common);
	fm_init_fpm(&reg->fm_fpm);

	/* clear DMA status */
	setbits_be32(&reg->fm_dma.fmdmsr, FMDMSR_CLEAR_ALL);

	/* set DMA mode */
	setbits_be32(&reg->fm_dma.fmdmmr, FMDMMR_SBER);

	return fm_init_bmi(index, &reg->fm_bmi_common);
	}