| /* |
| * (C) Copyright 2002 |
| * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC824X 1 |
| #define CONFIG_MPC8240 1 |
| #define CONFIG_PN62 1 |
| |
| #define CONFIG_CONS_INDEX 1 |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_BSP |
| |
| #undef CONFIG_CMD_AUTOSCRIPT |
| #undef CONFIG_CMD_LOADS |
| #undef CONFIG_CMD_ENV |
| #undef CONFIG_CMD_FLASH |
| #undef CONFIG_CMD_IMLS |
| |
| |
| #define CONFIG_BAUDRATE 19200 /* console baudrate */ |
| |
| #define CONFIG_BOOTDELAY 1 /* autoboot after n seconds */ |
| |
| #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ |
| |
| #define CONFIG_SERVERIP 10.0.0.201 |
| #define CONFIG_IPADDR 10.0.0.200 |
| #define CONFIG_ROOTPATH /opt/eldk/ppc_82xx |
| #define CONFIG_NETMASK 255.255.255.0 |
| #undef CONFIG_BOOTARGS |
| #if 0 |
| /* Boot Linux with NFS root filesystem */ |
| #define CONFIG_BOOTCOMMAND \ |
| "setenv verify y;" \ |
| "setenv bootargs console=ttyS0,19200 mem=31M quiet " \ |
| "root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ |
| "ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \ |
| "loadp 100000; bootm" |
| /* "tftpboot 100000 uImage; bootm" */ |
| #else |
| /* Boot Linux with RAMdisk based filesystem (initrd, BusyBox) */ |
| #define CONFIG_BOOTCOMMAND \ |
| "setenv verify n;" \ |
| "setenv bootargs console=ttyS0,19200 mem=31M quiet " \ |
| "root=/dev/ram rw " \ |
| "ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \ |
| "loadp 200000; bootm" |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP 1 /* undef to save memory */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| #define CFG_LOAD_ADDR 0x00100000 /* default load address */ |
| #define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_PRAM 1024 /* reserve 1 MB protected RAM */ |
| |
| #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() on init */ |
| |
| #define CONFIG_HAS_ETH1 1 /* add support for eth1addr */ |
| |
| #define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ |
| |
| /* |
| * PCI stuff |
| */ |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_PNP /* we need Plug 'n Play */ |
| #if 0 |
| #define CONFIG_PCI_SCAN_SHOW /* show PCI auto-scan at boot */ |
| #endif |
| |
| /* |
| * Networking stuff |
| */ |
| #define CONFIG_NET_MULTI /* Multi ethernet cards support */ |
| |
| #define CONFIG_PCNET /* there are 2 AMD PCnet 79C973 */ |
| #define CONFIG_PCNET_79C973 |
| |
| #define _IO_BASE 0xfe000000 /* points to PCI I/O space */ |
| |
| |
| /* |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CFG_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CFG_SDRAM_BASE 0x00000000 |
| #define CFG_MAX_RAM_SIZE 0x10000000 |
| |
| #define CFG_RESET_ADDRESS 0xfff00100 |
| |
| #undef CFG_RAMBOOT |
| #define CFG_MONITOR_LEN 0x00030000 |
| #define CFG_MONITOR_BASE TEXT_BASE |
| |
| /*#define CFG_GBL_DATA_SIZE 256*/ |
| #define CFG_GBL_DATA_SIZE 128 |
| |
| #define CFG_INIT_RAM_ADDR 0x40000000 |
| #define CFG_INIT_RAM_END 0x1000 |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| |
| |
| #define CFG_NO_FLASH 1 /* There is no FLASH memory */ |
| |
| #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CONFIG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */ |
| #define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */ |
| |
| #define CFG_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ |
| |
| #define CFG_MEMTEST_START 0x00004000 /* memtest works on */ |
| #define CFG_MEMTEST_END 0x01f00000 /* 0 ... 32 MB in DRAM */ |
| |
| /* |
| * Serial port configuration |
| */ |
| #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| #define CFG_NS16550 |
| #define CFG_NS16550_SERIAL |
| |
| #define CFG_NS16550_REG_SIZE 1 |
| |
| #define CFG_NS16550_CLK 1843200 |
| |
| #define CFG_NS16550_COM1 0xff800008 |
| #define CFG_NS16550_COM2 0xff800000 |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ |
| #define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3 |
| |
| #define CFG_EUMB_ADDR 0xFCE00000 |
| |
| /* MCCR1 */ |
| #define CFG_ROMNAL 3 /* rom/flash next access time */ |
| #define CFG_ROMFAL 7 /* rom/flash access time */ |
| |
| /* MCCR2 */ |
| #define CFG_ASRISE 6 /* ASRISE in clocks */ |
| #define CFG_ASFALL 12 /* ASFALL in clocks */ |
| #define CFG_REFINT 5600 /* REFINT in clocks */ |
| |
| /* MCCR3 */ |
| #define CFG_BSTOPRE 0x3cf /* Burst To Precharge */ |
| #define CFG_REFREC 2 /* Refresh to activate interval */ |
| #define CFG_RDLAT 3 /* data latency from read command */ |
| |
| /* MCCR4 */ |
| #define CFG_PRETOACT 1 /* Precharge to activate interval */ |
| #define CFG_ACTTOPRE 3 /* Activate to Precharge interval */ |
| #define CFG_ACTORW 2 /* Activate to R/W */ |
| #define CFG_SDMODE_CAS_LAT 2 /* SDMODE CAS latency */ |
| #define CFG_SDMODE_WRAP 0 /* SDMODE Wrap type */ |
| #define CFG_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */ |
| #define CFG_REGISTERD_TYPE_BUFFER 1 |
| |
| /* Memory bank settings: |
| * |
| * only bits 20-29 are actually used from these vales to set the |
| * start/qend address the upper two bits will be 0, and the lower 20 |
| * bits will be set to 0x00000 for a start address, or 0xfffff for an |
| * end address |
| */ |
| #define CFG_BANK0_START 0x00000000 |
| #define CFG_BANK0_END (CFG_MAX_RAM_SIZE - 1) |
| #define CFG_BANK0_ENABLE 1 |
| #define CFG_BANK1_START 0x00000000 |
| #define CFG_BANK1_END 0x00000000 |
| #define CFG_BANK1_ENABLE 0 |
| #define CFG_BANK2_START 0x00000000 |
| #define CFG_BANK2_END 0x00000000 |
| #define CFG_BANK2_ENABLE 0 |
| #define CFG_BANK3_START 0x00000000 |
| #define CFG_BANK3_END 0x00000000 |
| #define CFG_BANK3_ENABLE 0 |
| #define CFG_BANK4_START 0x00000000 |
| #define CFG_BANK4_END 0x00000000 |
| #define CFG_BANK4_ENABLE 0 |
| #define CFG_BANK5_START 0x00000000 |
| #define CFG_BANK5_END 0x00000000 |
| #define CFG_BANK5_ENABLE 0 |
| #define CFG_BANK6_START 0x00000000 |
| #define CFG_BANK6_END 0x00000000 |
| #define CFG_BANK6_ENABLE 0 |
| #define CFG_BANK7_START 0x00000000 |
| #define CFG_BANK7_END 0x00000000 |
| #define CFG_BANK7_ENABLE 0 |
| |
| /* |
| * Memory bank enable bitmask, specifying which of the banks defined above |
| * are actually present. MSB is for bank #7, LSB is for bank #0. |
| */ |
| #define CFG_BANK_ENABLE 0x01 |
| |
| #define CFG_ODCR 0xff /* configures line driver impedances, */ |
| /* see 8240 book for bit definitions */ |
| #define CFG_PGMAX 0x32 /* how long the 8240 retains the */ |
| /* currently accessed page in memory */ |
| /* see 8240 book for details */ |
| |
| /* SDRAM 0 - 256MB */ |
| #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| #define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| |
| /* PCI memory space */ |
| #define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) |
| #define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| /* Config addrs, etc */ |
| #define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) |
| #define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| #define CFG_DBAT0L CFG_IBAT0L |
| #define CFG_DBAT0U CFG_IBAT0U |
| #define CFG_DBAT1L CFG_IBAT1L |
| #define CFG_DBAT1U CFG_IBAT1U |
| #define CFG_DBAT2L CFG_IBAT2L |
| #define CFG_DBAT2U CFG_IBAT2U |
| #define CFG_DBAT3L CFG_IBAT3L |
| #define CFG_DBAT3U CFG_IBAT3U |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Cache Configuration |
| */ |
| #define CFG_CACHELINE_SIZE 32 /* For MPC8240 CPU */ |
| #if defined(CONFIG_CMD_KGDB) |
| # define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| |
| #endif /* __CONFIG_H */ |