| /* |
| * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __PINCTRL_H |
| #define __PINCTRL_H |
| |
| /** |
| * struct pinconf_param - pin config parameters |
| * |
| * @property: property name in DT nodes |
| * @param: ID for this config parameter |
| * @default_value: default value for this config parameter used in case |
| * no value is specified in DT nodes |
| */ |
| struct pinconf_param { |
| const char * const property; |
| unsigned int param; |
| u32 default_value; |
| }; |
| |
| /** |
| * struct pinctrl_ops - pin control operations, to be implemented by |
| * pin controller drivers. |
| * |
| * The @set_state is the only mandatory operation. You can implement your |
| * pinctrl driver with its own @set_state. In this case, the other callbacks |
| * are not required. Otherwise, generic pinctrl framework is also available; |
| * use pinctrl_generic_set_state for @set_state, and implement other operations |
| * depending on your necessity. |
| * |
| * @get_pins_count: return number of selectable named pins available |
| * in this driver. (necessary to parse "pins" property in DTS) |
| * @get_pin_name: return the pin name of the pin selector, |
| * called by the core to figure out which pin it shall do |
| * operations to. (necessary to parse "pins" property in DTS) |
| * @get_groups_count: return number of selectable named groups available |
| * in this driver. (necessary to parse "groups" property in DTS) |
| * @get_group_name: return the group name of the group selector, |
| * called by the core to figure out which pin group it shall do |
| * operations to. (necessary to parse "groups" property in DTS) |
| * @get_functions_count: return number of selectable named functions available |
| * in this driver. (necessary for pin-muxing) |
| * @get_function_name: return the function name of the muxing selector, |
| * called by the core to figure out which mux setting it shall map a |
| * certain device to. (necessary for pin-muxing) |
| * @pinmux_set: enable a certain muxing function with a certain pin. |
| * The @func_selector selects a certain function whereas @pin_selector |
| * selects a certain pin to be used. On simple controllers one of them |
| * may be ignored. (necessary for pin-muxing against a single pin) |
| * @pinmux_group_set: enable a certain muxing function with a certain pin |
| * group. The @func_selector selects a certain function whereas |
| * @group_selector selects a certain set of pins to be used. On simple |
| * controllers one of them may be ignored. |
| * (necessary for pin-muxing against a pin group) |
| * @pinconf_num_params: number of driver-specific parameters to be parsed |
| * from device trees (necessary for pin-configuration) |
| * @pinconf_params: list of driver_specific parameters to be parsed from |
| * device trees (necessary for pin-configuration) |
| * @pinconf_set: configure an individual pin with a given parameter. |
| * (necessary for pin-configuration against a single pin) |
| * @pinconf_group_set: configure all pins in a group with a given parameter. |
| * (necessary for pin-configuration against a pin group) |
| * @set_state: do pinctrl operations specified by @config, a pseudo device |
| * pointing a config node. (necessary for pinctrl_full) |
| * @set_state_simple: do needed pinctrl operations for a peripherl @periph. |
| * (necessary for pinctrl_simple) |
| */ |
| struct pinctrl_ops { |
| int (*get_pins_count)(struct udevice *dev); |
| const char *(*get_pin_name)(struct udevice *dev, unsigned selector); |
| int (*get_groups_count)(struct udevice *dev); |
| const char *(*get_group_name)(struct udevice *dev, unsigned selector); |
| int (*get_functions_count)(struct udevice *dev); |
| const char *(*get_function_name)(struct udevice *dev, |
| unsigned selector); |
| int (*pinmux_set)(struct udevice *dev, unsigned pin_selector, |
| unsigned func_selector); |
| int (*pinmux_group_set)(struct udevice *dev, unsigned group_selector, |
| unsigned func_selector); |
| unsigned int pinconf_num_params; |
| const struct pinconf_param *pinconf_params; |
| int (*pinconf_set)(struct udevice *dev, unsigned pin_selector, |
| unsigned param, unsigned argument); |
| int (*pinconf_group_set)(struct udevice *dev, unsigned group_selector, |
| unsigned param, unsigned argument); |
| int (*set_state)(struct udevice *dev, struct udevice *config); |
| int (*set_state_simple)(struct udevice *dev, struct udevice *periph); |
| }; |
| |
| #define pinctrl_get_ops(dev) ((struct pinctrl_ops *)(dev)->driver->ops) |
| |
| /** |
| * Generic pin configuration paramters |
| * |
| * @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a |
| * transition from say pull-up to pull-down implies that you disable |
| * pull-up in the process, this setting disables all biasing. |
| * @PIN_CONFIG_BIAS_HIGH_IMPEDANCE: the pin will be set to a high impedance |
| * mode, also know as "third-state" (tristate) or "high-Z" or "floating". |
| * On output pins this effectively disconnects the pin, which is useful |
| * if for example some other pin is going to drive the signal connected |
| * to it for a while. Pins used for input are usually always high |
| * impedance. |
| * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it |
| * weakly drives the last value on a tristate bus, also known as a "bus |
| * holder", "bus keeper" or "repeater". This allows another device on the |
| * bus to change the value by driving the bus high or low and switching to |
| * tristate. The argument is ignored. |
| * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high |
| * impedance to VDD). If the argument is != 0 pull-up is enabled, |
| * if it is 0, pull-up is total, i.e. the pin is connected to VDD. |
| * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high |
| * impedance to GROUND). If the argument is != 0 pull-down is enabled, |
| * if it is 0, pull-down is total, i.e. the pin is connected to GROUND. |
| * @PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: the pin will be pulled up or down based |
| * on embedded knowledge of the controller hardware, like current mux |
| * function. The pull direction and possibly strength too will normally |
| * be decided completely inside the hardware block and not be readable |
| * from the kernel side. |
| * If the argument is != 0 pull up/down is enabled, if it is 0, the |
| * configuration is ignored. The proper way to disable it is to use |
| * @PIN_CONFIG_BIAS_DISABLE. |
| * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and |
| * low, this is the most typical case and is typically achieved with two |
| * active transistors on the output. Setting this config will enable |
| * push-pull mode, the argument is ignored. |
| * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open |
| * collector) which means it is usually wired with other output ports |
| * which are then pulled up with an external resistor. Setting this |
| * config will enable open drain mode, the argument is ignored. |
| * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source |
| * (open emitter). Setting this config will enable open source mode, the |
| * argument is ignored. |
| * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current |
| * passed as argument. The argument is in mA. |
| * @PIN_CONFIG_INPUT_ENABLE: enable the pin's input. Note that this does not |
| * affect the pin's ability to drive output. 1 enables input, 0 disables |
| * input. |
| * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin. |
| * If the argument != 0, schmitt-trigger mode is enabled. If it's 0, |
| * schmitt-trigger mode is disabled. |
| * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in |
| * schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis, |
| * the threshold value is given on a custom format as argument when |
| * setting pins to this mode. |
| * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode, |
| * which means it will wait for signals to settle when reading inputs. The |
| * argument gives the debounce time in usecs. Setting the |
| * argument to zero turns debouncing off. |
| * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power |
| * supplies, the argument to this parameter (on a custom format) tells |
| * the driver which alternative power source to use. |
| * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to |
| * this parameter (on a custom format) tells the driver which alternative |
| * slew rate to use. |
| * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power |
| * operation, if several modes of operation are supported these can be |
| * passed in the argument on a custom form, else just use argument 1 |
| * to indicate low power mode, argument 0 turns low power mode off. |
| * @PIN_CONFIG_OUTPUT: this will configure the pin as an output. Use argument |
| * 1 to indicate high level, argument 0 to indicate low level. (Please |
| * see Documentation/pinctrl.txt, section "GPIO mode pitfalls" for a |
| * discussion around this parameter.) |
| * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if |
| * you need to pass in custom configurations to the pin controller, use |
| * PIN_CONFIG_END+1 as the base offset. |
| */ |
| #define PIN_CONFIG_BIAS_DISABLE 0 |
| #define PIN_CONFIG_BIAS_HIGH_IMPEDANCE 1 |
| #define PIN_CONFIG_BIAS_BUS_HOLD 2 |
| #define PIN_CONFIG_BIAS_PULL_UP 3 |
| #define PIN_CONFIG_BIAS_PULL_DOWN 4 |
| #define PIN_CONFIG_BIAS_PULL_PIN_DEFAULT 5 |
| #define PIN_CONFIG_DRIVE_PUSH_PULL 6 |
| #define PIN_CONFIG_DRIVE_OPEN_DRAIN 7 |
| #define PIN_CONFIG_DRIVE_OPEN_SOURCE 8 |
| #define PIN_CONFIG_DRIVE_STRENGTH 9 |
| #define PIN_CONFIG_INPUT_ENABLE 10 |
| #define PIN_CONFIG_INPUT_SCHMITT_ENABLE 11 |
| #define PIN_CONFIG_INPUT_SCHMITT 12 |
| #define PIN_CONFIG_INPUT_DEBOUNCE 13 |
| #define PIN_CONFIG_POWER_SOURCE 14 |
| #define PIN_CONFIG_SLEW_RATE 15 |
| #define PIN_CONFIG_LOW_POWER_MODE 16 |
| #define PIN_CONFIG_OUTPUT 17 |
| #define PIN_CONFIG_END 0x7FFF |
| |
| #if CONFIG_IS_ENABLED(PINCTRL_GENERIC) |
| /** |
| * pinctrl_generic_set_state() - generic set_state operation |
| * Parse the DT node of @config and its children and handle generic properties |
| * such as "pins", "groups", "functions", and pin configuration parameters. |
| * |
| * @pctldev: pinctrl device |
| * @config: config device (pseudo device), pointing a config node in DTS |
| * @return: 0 on success, or negative error code on failure |
| */ |
| int pinctrl_generic_set_state(struct udevice *pctldev, struct udevice *config); |
| #else |
| static inline int pinctrl_generic_set_state(struct udevice *pctldev, |
| struct udevice *config) |
| { |
| return -EINVAL; |
| } |
| #endif |
| |
| #if CONFIG_IS_ENABLED(PINCTRL) |
| /** |
| * pinctrl_select_state() - set a device to a given state |
| * |
| * @dev: peripheral device |
| * @statename: state name, like "default" |
| * @return: 0 on success, or negative error code on failure |
| */ |
| int pinctrl_select_state(struct udevice *dev, const char *statename); |
| #else |
| static inline int pinctrl_select_state(struct udevice *dev, |
| const char *statename) |
| { |
| return -EINVAL; |
| } |
| #endif |
| |
| #endif /* __PINCTRL_H */ |