| /* |
| * (C) Copyright 2007-2010 Michal Simek |
| * |
| * Michal SIMEK <monstr@monstr.eu> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #include "../board/xilinx/microblaze-generic/xparameters.h" |
| |
| /* MicroBlaze CPU */ |
| #define MICROBLAZE_V5 1 |
| |
| /* linear and spi flash memory */ |
| #ifdef XILINX_FLASH_START |
| #define FLASH |
| #undef SPIFLASH |
| #undef RAMENV /* hold environment in flash */ |
| #else |
| #ifdef XILINX_SPI_FLASH_BASEADDR |
| #undef FLASH |
| #define SPIFLASH |
| #undef RAMENV /* hold environment in flash */ |
| #else |
| #undef FLASH |
| #undef SPIFLASH |
| #define RAMENV /* hold environment in RAM */ |
| #endif |
| #endif |
| |
| /* uart */ |
| #ifdef XILINX_UARTLITE_BASEADDR |
| # define CONFIG_XILINX_UARTLITE |
| # define CONFIG_SERIAL_BASE XILINX_UARTLITE_BASEADDR |
| # define CONFIG_BAUDRATE XILINX_UARTLITE_BAUDRATE |
| # define CONFIG_SYS_BAUDRATE_TABLE { CONFIG_BAUDRATE } |
| # define CONSOLE_ARG "console=console=ttyUL0,115200\0" |
| #elif XILINX_UART16550_BASEADDR |
| # define CONFIG_SYS_NS16550 1 |
| # define CONFIG_SYS_NS16550_SERIAL |
| # if defined(__MICROBLAZEEL__) |
| # define CONFIG_SYS_NS16550_REG_SIZE -4 |
| # else |
| # define CONFIG_SYS_NS16550_REG_SIZE 4 |
| # endif |
| # define CONFIG_CONS_INDEX 1 |
| # define CONFIG_SYS_NS16550_COM1 \ |
| ((XILINX_UART16550_BASEADDR & ~0xF) + 0x1000) |
| # define CONFIG_SYS_NS16550_CLK XILINX_UART16550_CLOCK_HZ |
| # define CONFIG_BAUDRATE 115200 |
| |
| /* The following table includes the supported baudrates */ |
| # define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} |
| # define CONSOLE_ARG "console=console=ttyS0,115200\0" |
| #else |
| # error Undefined uart |
| #endif |
| |
| /* setting reset address */ |
| /*#define CONFIG_SYS_RESET_ADDRESS CONFIG_SYS_TEXT_BASE*/ |
| |
| /* ethernet */ |
| #undef CONFIG_SYS_ENET |
| #if defined(XILINX_EMACLITE_BASEADDR) || defined(CONFIG_OF_CONTROL) |
| # define CONFIG_XILINX_EMACLITE 1 |
| # define CONFIG_SYS_ENET |
| #endif |
| #if defined(XILINX_LLTEMAC_BASEADDR) |
| # define CONFIG_XILINX_LL_TEMAC 1 |
| # define CONFIG_SYS_ENET |
| #endif |
| #if defined(XILINX_AXIEMAC_BASEADDR) |
| # define CONFIG_XILINX_AXIEMAC 1 |
| # define CONFIG_SYS_ENET |
| #endif |
| |
| #undef ET_DEBUG |
| |
| /* gpio */ |
| #ifdef XILINX_GPIO_BASEADDR |
| # define CONFIG_XILINX_GPIO |
| # define CONFIG_SYS_GPIO_0_ADDR XILINX_GPIO_BASEADDR |
| #endif |
| |
| /* interrupt controller */ |
| #ifdef XILINX_INTC_BASEADDR |
| # define CONFIG_SYS_INTC_0_ADDR XILINX_INTC_BASEADDR |
| # define CONFIG_SYS_INTC_0_NUM XILINX_INTC_NUM_INTR_INPUTS |
| #endif |
| |
| /* timer */ |
| #if defined(XILINX_TIMER_BASEADDR) && defined(XILINX_TIMER_IRQ) |
| # define CONFIG_SYS_TIMER_0_ADDR XILINX_TIMER_BASEADDR |
| # define CONFIG_SYS_TIMER_0_IRQ XILINX_TIMER_IRQ |
| #endif |
| |
| /* watchdog */ |
| #if defined(XILINX_WATCHDOG_BASEADDR) && defined(XILINX_WATCHDOG_IRQ) |
| # define CONFIG_WATCHDOG_BASEADDR XILINX_WATCHDOG_BASEADDR |
| # define CONFIG_WATCHDOG_IRQ XILINX_WATCHDOG_IRQ |
| # define CONFIG_HW_WATCHDOG |
| # define CONFIG_XILINX_TB_WATCHDOG |
| #endif |
| |
| #ifndef CONFIG_OF_CONTROL |
| /* ddr sdram - main memory */ |
| # define CONFIG_SYS_SDRAM_BASE XILINX_RAM_START |
| # define CONFIG_SYS_SDRAM_SIZE XILINX_RAM_SIZE |
| #endif |
| |
| #define CONFIG_SYS_MALLOC_LEN 0xC0000 |
| #ifndef CONFIG_SPL_BUILD |
| # define CONFIG_SYS_MALLOC_F_LEN 1024 |
| #else |
| # define CONFIG_SYS_MALLOC_SIMPLE |
| # define CONFIG_SYS_MALLOC_F_LEN 0x150 |
| #endif |
| |
| /* Stack location before relocation */ |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_TEXT_BASE |
| |
| /* |
| * CFI flash memory layout - Example |
| * CONFIG_SYS_FLASH_BASE = 0x2200_0000; |
| * CONFIG_SYS_FLASH_SIZE = 0x0080_0000; 8MB |
| * |
| * SECT_SIZE = 0x20000; 128kB is one sector |
| * CONFIG_ENV_SIZE = SECT_SIZE; 128kB environment store |
| * |
| * 0x2200_0000 CONFIG_SYS_FLASH_BASE |
| * FREE 256kB |
| * 0x2204_0000 CONFIG_ENV_ADDR |
| * ENV_AREA 128kB |
| * 0x2206_0000 |
| * FREE |
| * 0x2280_0000 CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE |
| * |
| */ |
| |
| #ifdef FLASH |
| # define CONFIG_SYS_FLASH_BASE XILINX_FLASH_START |
| # define CONFIG_SYS_FLASH_SIZE XILINX_FLASH_SIZE |
| # define CONFIG_SYS_FLASH_CFI 1 |
| # define CONFIG_FLASH_CFI_DRIVER 1 |
| /* ?empty sector */ |
| # define CONFIG_SYS_FLASH_EMPTY_INFO 1 |
| /* max number of memory banks */ |
| # define CONFIG_SYS_MAX_FLASH_BANKS 1 |
| /* max number of sectors on one chip */ |
| # define CONFIG_SYS_MAX_FLASH_SECT 512 |
| /* hardware flash protection */ |
| # define CONFIG_SYS_FLASH_PROTECTION |
| /* use buffered writes (20x faster) */ |
| # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 |
| # ifdef RAMENV |
| # define CONFIG_ENV_IS_NOWHERE 1 |
| # define CONFIG_ENV_SIZE 0x1000 |
| # define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) |
| |
| # else /* FLASH && !RAMENV */ |
| # define CONFIG_ENV_IS_IN_FLASH 1 |
| /* 128K(one sector) for env */ |
| # define CONFIG_ENV_SECT_SIZE 0x20000 |
| # define CONFIG_ENV_ADDR \ |
| (CONFIG_SYS_FLASH_BASE + (2 * CONFIG_ENV_SECT_SIZE)) |
| # define CONFIG_ENV_SIZE 0x20000 |
| # endif /* FLASH && !RAMBOOT */ |
| #else /* !FLASH */ |
| |
| #ifdef SPIFLASH |
| # define CONFIG_SYS_NO_FLASH 1 |
| # define CONFIG_SYS_SPI_BASE XILINX_SPI_FLASH_BASEADDR |
| # define CONFIG_XILINX_SPI 1 |
| # define CONFIG_SPI 1 |
| # define CONFIG_SPI_FLASH_STMICRO 1 |
| # define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 |
| # define CONFIG_SF_DEFAULT_SPEED XILINX_SPI_FLASH_MAX_FREQ |
| # define CONFIG_SF_DEFAULT_CS XILINX_SPI_FLASH_CS |
| |
| # ifdef RAMENV |
| # define CONFIG_ENV_IS_NOWHERE 1 |
| # define CONFIG_ENV_SIZE 0x1000 |
| # define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) |
| |
| # else /* SPIFLASH && !RAMENV */ |
| # define CONFIG_ENV_IS_IN_SPI_FLASH 1 |
| # define CONFIG_ENV_SPI_MODE SPI_MODE_3 |
| # define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED |
| # define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS |
| /* 128K(two sectors) for env */ |
| # define CONFIG_ENV_SECT_SIZE 0x10000 |
| # define CONFIG_ENV_SIZE (2 * CONFIG_ENV_SECT_SIZE) |
| /* Warning: adjust the offset in respect of other flash content and size */ |
| # define CONFIG_ENV_OFFSET (128 * CONFIG_ENV_SECT_SIZE) /* at 8MB */ |
| # endif /* SPIFLASH && !RAMBOOT */ |
| #else /* !SPIFLASH */ |
| |
| /* ENV in RAM */ |
| # define CONFIG_SYS_NO_FLASH 1 |
| # define CONFIG_ENV_IS_NOWHERE 1 |
| # define CONFIG_ENV_SIZE 0x1000 |
| # define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SIZE) |
| #endif /* !SPIFLASH */ |
| #endif /* !FLASH */ |
| |
| /* system ace */ |
| #ifdef XILINX_SYSACE_BASEADDR |
| # define CONFIG_SYSTEMACE |
| /* #define DEBUG_SYSTEMACE */ |
| # define SYSTEMACE_CONFIG_FPGA |
| # define CONFIG_SYS_SYSTEMACE_BASE XILINX_SYSACE_BASEADDR |
| # define CONFIG_SYS_SYSTEMACE_WIDTH XILINX_SYSACE_MEM_WIDTH |
| # define CONFIG_DOS_PARTITION |
| #endif |
| |
| #if defined(XILINX_USE_ICACHE) |
| # define CONFIG_ICACHE |
| #else |
| # undef CONFIG_ICACHE |
| #endif |
| |
| #if defined(XILINX_USE_DCACHE) |
| # define CONFIG_DCACHE |
| #else |
| # undef CONFIG_DCACHE |
| #endif |
| |
| #ifndef XILINX_DCACHE_BYTE_SIZE |
| #define XILINX_DCACHE_BYTE_SIZE 32768 |
| #endif |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| /* |
| * Command line configuration. |
| */ |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_MFSL |
| #define CONFIG_CMD_GPIO |
| |
| #if defined(CONFIG_DCACHE) || defined(CONFIG_ICACHE) |
| # define CONFIG_CMD_CACHE |
| #else |
| # undef CONFIG_CMD_CACHE |
| #endif |
| |
| #ifdef CONFIG_SYS_ENET |
| # define CONFIG_CMD_PING |
| # define CONFIG_CMD_DHCP |
| # define CONFIG_CMD_TFTPPUT |
| #endif |
| |
| #if defined(CONFIG_SYSTEMACE) |
| # define CONFIG_CMD_EXT2 |
| # define CONFIG_CMD_FAT |
| #endif |
| |
| #if defined(FLASH) |
| # define CONFIG_CMD_JFFS2 |
| # define CONFIG_CMD_UBI |
| # undef CONFIG_CMD_UBIFS |
| |
| # if !defined(RAMENV) |
| # define CONFIG_CMD_SAVES |
| # endif |
| |
| #else |
| #if defined(SPIFLASH) |
| # define CONFIG_CMD_SF |
| |
| # if !defined(RAMENV) |
| # define CONFIG_CMD_SAVES |
| # endif |
| #else |
| # undef CONFIG_CMD_JFFS2 |
| # undef CONFIG_CMD_UBI |
| # undef CONFIG_CMD_UBIFS |
| #endif |
| #endif |
| |
| #if defined(CONFIG_CMD_JFFS2) |
| # define CONFIG_MTD_PARTITIONS |
| #endif |
| |
| #if defined(CONFIG_CMD_UBIFS) |
| # define CONFIG_CMD_UBI |
| # define CONFIG_LZO |
| #endif |
| |
| #if defined(CONFIG_CMD_UBI) |
| # define CONFIG_MTD_PARTITIONS |
| # define CONFIG_RBTREE |
| #endif |
| |
| #if defined(CONFIG_MTD_PARTITIONS) |
| /* MTD partitions */ |
| #define CONFIG_CMD_MTDPARTS /* mtdparts command line support */ |
| #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ |
| #define CONFIG_FLASH_CFI_MTD |
| #define MTDIDS_DEFAULT "nor0=flash-0" |
| |
| /* default mtd partition table */ |
| #define MTDPARTS_DEFAULT "mtdparts=flash-0:256k(u-boot),"\ |
| "256k(env),3m(kernel),1m(romfs),"\ |
| "1m(cramfs),-(jffs2)" |
| #endif |
| |
| /* Miscellaneous configurable options */ |
| #define CONFIG_SYS_PROMPT "U-Boot-mONStR> " |
| /* size of console buffer */ |
| #define CONFIG_SYS_CBSIZE 512 |
| /* print buffer size */ |
| #define CONFIG_SYS_PBSIZE \ |
| (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| /* max number of command args */ |
| #define CONFIG_SYS_MAXARGS 15 |
| #define CONFIG_SYS_LONGHELP |
| /* default load address */ |
| #define CONFIG_SYS_LOAD_ADDR XILINX_RAM_START |
| |
| #define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ |
| #define CONFIG_BOOTARGS "root=romfs" |
| #define CONFIG_HOSTNAME XILINX_BOARD_NAME |
| #define CONFIG_BOOTCOMMAND "base 0;tftp 11000000 image.img;bootm" |
| #define CONFIG_IPADDR 192.168.0.3 |
| #define CONFIG_SERVERIP 192.168.0.5 |
| #define CONFIG_GATEWAYIP 192.168.0.1 |
| |
| /* architecture dependent code */ |
| #define CONFIG_SYS_USR_EXCEP /* user exception */ |
| |
| #define CONFIG_PREBOOT "echo U-BOOT for ${hostname};setenv preboot;echo" |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS "unlock=yes\0" \ |
| "nor0=flash-0\0"\ |
| "mtdparts=mtdparts=flash-0:"\ |
| "256k(u-boot),256k(env),3m(kernel),"\ |
| "1m(romfs),1m(cramfs),-(jffs2)\0"\ |
| "nc=setenv stdout nc;"\ |
| "setenv stdin nc\0" \ |
| "serial=setenv stdout serial;"\ |
| "setenv stdin serial\0" |
| |
| #define CONFIG_CMDLINE_EDITING |
| |
| #define CONFIG_NETCONSOLE |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV |
| |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| /* Enable flat device tree support */ |
| #define CONFIG_LMB 1 |
| #define CONFIG_FIT 1 |
| #define CONFIG_OF_LIBFDT 1 |
| |
| #if defined(CONFIG_XILINX_LL_TEMAC) || defined(CONFIG_XILINX_AXIEMAC) |
| # define CONFIG_MII 1 |
| # define CONFIG_CMD_MII 1 |
| # define CONFIG_PHY_GIGE 1 |
| # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 1 |
| # define CONFIG_PHYLIB 1 |
| # define CONFIG_PHY_ATHEROS 1 |
| # define CONFIG_PHY_BROADCOM 1 |
| # define CONFIG_PHY_DAVICOM 1 |
| # define CONFIG_PHY_LXT 1 |
| # define CONFIG_PHY_MARVELL 1 |
| # define CONFIG_PHY_MICREL 1 |
| # define CONFIG_PHY_NATSEMI 1 |
| # define CONFIG_PHY_REALTEK 1 |
| # define CONFIG_PHY_VITESSE 1 |
| #else |
| # undef CONFIG_MII |
| # undef CONFIG_CMD_MII |
| # undef CONFIG_PHYLIB |
| #endif |
| |
| /* SPL part */ |
| #define CONFIG_CMD_SPL |
| #define CONFIG_SPL_FRAMEWORK |
| #define CONFIG_SPL_LIBCOMMON_SUPPORT |
| #define CONFIG_SPL_LIBGENERIC_SUPPORT |
| #define CONFIG_SPL_SERIAL_SUPPORT |
| #define CONFIG_SPL_BOARD_INIT |
| |
| #define CONFIG_SPL_LDSCRIPT "arch/microblaze/cpu/u-boot-spl.lds" |
| |
| #define CONFIG_SPL_RAM_DEVICE |
| #ifdef CONFIG_SYS_FLASH_BASE |
| # define CONFIG_SPL_NOR_SUPPORT |
| # define CONFIG_SYS_UBOOT_BASE CONFIG_SYS_FLASH_BASE |
| #endif |
| |
| /* for booting directly linux */ |
| #define CONFIG_SPL_OS_BOOT |
| |
| #define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + \ |
| 0x60000) |
| #define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + \ |
| 0x40000) |
| #define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_TEXT_BASE + \ |
| 0x1000000) |
| |
| /* SP location before relocation, must use scratch RAM */ |
| /* BRAM start */ |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x0 |
| /* BRAM size - will be generated */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x100000 |
| |
| # define CONFIG_SPL_STACK_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ |
| CONFIG_SYS_INIT_RAM_SIZE - \ |
| CONFIG_SYS_MALLOC_F_LEN) |
| |
| /* Just for sure that there is a space for stack */ |
| #define CONFIG_SPL_STACK_SIZE 0x100 |
| |
| #define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE |
| |
| #define CONFIG_SPL_MAX_FOOTPRINT (CONFIG_SYS_INIT_RAM_SIZE - \ |
| CONFIG_SYS_INIT_RAM_ADDR - \ |
| CONFIG_SYS_MALLOC_F_LEN - \ |
| CONFIG_SPL_STACK_SIZE) |
| |
| #endif /* __CONFIG_H */ |