| /* |
| * (C) Copyright 2010 |
| * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * Designware ethernet IP driver for u-boot |
| */ |
| |
| #include <common.h> |
| #include <miiphy.h> |
| #include <malloc.h> |
| #include <linux/compiler.h> |
| #include <linux/err.h> |
| #include <asm/io.h> |
| #include "designware.h" |
| |
| static int configure_phy(struct eth_device *dev); |
| |
| static void tx_descs_init(struct eth_device *dev) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| struct dmamacdescr *desc_table_p = &priv->tx_mac_descrtable[0]; |
| char *txbuffs = &priv->txbuffs[0]; |
| struct dmamacdescr *desc_p; |
| u32 idx; |
| |
| for (idx = 0; idx < CONFIG_TX_DESCR_NUM; idx++) { |
| desc_p = &desc_table_p[idx]; |
| desc_p->dmamac_addr = &txbuffs[idx * CONFIG_ETH_BUFSIZE]; |
| desc_p->dmamac_next = &desc_table_p[idx + 1]; |
| |
| #if defined(CONFIG_DW_ALTDESCRIPTOR) |
| desc_p->txrx_status &= ~(DESC_TXSTS_TXINT | DESC_TXSTS_TXLAST | |
| DESC_TXSTS_TXFIRST | DESC_TXSTS_TXCRCDIS | \ |
| DESC_TXSTS_TXCHECKINSCTRL | \ |
| DESC_TXSTS_TXRINGEND | DESC_TXSTS_TXPADDIS); |
| |
| desc_p->txrx_status |= DESC_TXSTS_TXCHAIN; |
| desc_p->dmamac_cntl = 0; |
| desc_p->txrx_status &= ~(DESC_TXSTS_MSK | DESC_TXSTS_OWNBYDMA); |
| #else |
| desc_p->dmamac_cntl = DESC_TXCTRL_TXCHAIN; |
| desc_p->txrx_status = 0; |
| #endif |
| } |
| |
| /* Correcting the last pointer of the chain */ |
| desc_p->dmamac_next = &desc_table_p[0]; |
| |
| writel((ulong)&desc_table_p[0], &dma_p->txdesclistaddr); |
| } |
| |
| static void rx_descs_init(struct eth_device *dev) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| struct dmamacdescr *desc_table_p = &priv->rx_mac_descrtable[0]; |
| char *rxbuffs = &priv->rxbuffs[0]; |
| struct dmamacdescr *desc_p; |
| u32 idx; |
| |
| for (idx = 0; idx < CONFIG_RX_DESCR_NUM; idx++) { |
| desc_p = &desc_table_p[idx]; |
| desc_p->dmamac_addr = &rxbuffs[idx * CONFIG_ETH_BUFSIZE]; |
| desc_p->dmamac_next = &desc_table_p[idx + 1]; |
| |
| desc_p->dmamac_cntl = |
| (MAC_MAX_FRAME_SZ & DESC_RXCTRL_SIZE1MASK) | \ |
| DESC_RXCTRL_RXCHAIN; |
| |
| desc_p->txrx_status = DESC_RXSTS_OWNBYDMA; |
| } |
| |
| /* Correcting the last pointer of the chain */ |
| desc_p->dmamac_next = &desc_table_p[0]; |
| |
| writel((ulong)&desc_table_p[0], &dma_p->rxdesclistaddr); |
| } |
| |
| static void descs_init(struct eth_device *dev) |
| { |
| tx_descs_init(dev); |
| rx_descs_init(dev); |
| } |
| |
| static int mac_reset(struct eth_device *dev) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| struct eth_mac_regs *mac_p = priv->mac_regs_p; |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| |
| ulong start; |
| int timeout = CONFIG_MACRESET_TIMEOUT; |
| |
| writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode); |
| |
| if (priv->interface != PHY_INTERFACE_MODE_RGMII) |
| writel(MII_PORTSELECT, &mac_p->conf); |
| |
| start = get_timer(0); |
| while (get_timer(start) < timeout) { |
| if (!(readl(&dma_p->busmode) & DMAMAC_SRST)) |
| return 0; |
| |
| /* Try again after 10usec */ |
| udelay(10); |
| }; |
| |
| return -1; |
| } |
| |
| static int dw_write_hwaddr(struct eth_device *dev) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| struct eth_mac_regs *mac_p = priv->mac_regs_p; |
| u32 macid_lo, macid_hi; |
| u8 *mac_id = &dev->enetaddr[0]; |
| |
| macid_lo = mac_id[0] + (mac_id[1] << 8) + \ |
| (mac_id[2] << 16) + (mac_id[3] << 24); |
| macid_hi = mac_id[4] + (mac_id[5] << 8); |
| |
| writel(macid_hi, &mac_p->macaddr0hi); |
| writel(macid_lo, &mac_p->macaddr0lo); |
| |
| return 0; |
| } |
| |
| static int dw_eth_init(struct eth_device *dev, bd_t *bis) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| struct eth_mac_regs *mac_p = priv->mac_regs_p; |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| u32 conf; |
| |
| if (priv->phy_configured != 1) |
| configure_phy(dev); |
| |
| /* Print link status only once */ |
| if (!priv->link_printed) { |
| printf("ENET Speed is %d Mbps - %s duplex connection\n", |
| priv->speed, (priv->duplex == HALF) ? "HALF" : "FULL"); |
| priv->link_printed = 1; |
| } |
| |
| /* Reset ethernet hardware */ |
| if (mac_reset(dev) < 0) |
| return -1; |
| |
| /* Resore the HW MAC address as it has been lost during MAC reset */ |
| dw_write_hwaddr(dev); |
| |
| writel(FIXEDBURST | PRIORXTX_41 | BURST_16, |
| &dma_p->busmode); |
| |
| writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD | |
| TXSECONDFRAME, &dma_p->opmode); |
| |
| conf = FRAMEBURSTENABLE | DISABLERXOWN; |
| |
| if (priv->speed != 1000) |
| conf |= MII_PORTSELECT; |
| |
| if ((priv->interface != PHY_INTERFACE_MODE_MII) && |
| (priv->interface != PHY_INTERFACE_MODE_GMII)) { |
| |
| if (priv->speed == 100) |
| conf |= FES_100; |
| } |
| |
| if (priv->duplex == FULL) |
| conf |= FULLDPLXMODE; |
| |
| writel(conf, &mac_p->conf); |
| |
| descs_init(dev); |
| |
| /* |
| * Start/Enable xfer at dma as well as mac level |
| */ |
| writel(readl(&dma_p->opmode) | RXSTART, &dma_p->opmode); |
| writel(readl(&dma_p->opmode) | TXSTART, &dma_p->opmode); |
| |
| writel(readl(&mac_p->conf) | RXENABLE | TXENABLE, &mac_p->conf); |
| |
| return 0; |
| } |
| |
| static int dw_eth_send(struct eth_device *dev, void *packet, int length) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| struct eth_dma_regs *dma_p = priv->dma_regs_p; |
| u32 desc_num = priv->tx_currdescnum; |
| struct dmamacdescr *desc_p = &priv->tx_mac_descrtable[desc_num]; |
| |
| /* Check if the descriptor is owned by CPU */ |
| if (desc_p->txrx_status & DESC_TXSTS_OWNBYDMA) { |
| printf("CPU not owner of tx frame\n"); |
| return -1; |
| } |
| |
| memcpy((void *)desc_p->dmamac_addr, packet, length); |
| |
| #if defined(CONFIG_DW_ALTDESCRIPTOR) |
| desc_p->txrx_status |= DESC_TXSTS_TXFIRST | DESC_TXSTS_TXLAST; |
| desc_p->dmamac_cntl |= (length << DESC_TXCTRL_SIZE1SHFT) & \ |
| DESC_TXCTRL_SIZE1MASK; |
| |
| desc_p->txrx_status &= ~(DESC_TXSTS_MSK); |
| desc_p->txrx_status |= DESC_TXSTS_OWNBYDMA; |
| #else |
| desc_p->dmamac_cntl |= ((length << DESC_TXCTRL_SIZE1SHFT) & \ |
| DESC_TXCTRL_SIZE1MASK) | DESC_TXCTRL_TXLAST | \ |
| DESC_TXCTRL_TXFIRST; |
| |
| desc_p->txrx_status = DESC_TXSTS_OWNBYDMA; |
| #endif |
| |
| /* Test the wrap-around condition. */ |
| if (++desc_num >= CONFIG_TX_DESCR_NUM) |
| desc_num = 0; |
| |
| priv->tx_currdescnum = desc_num; |
| |
| /* Start the transmission */ |
| writel(POLL_DATA, &dma_p->txpolldemand); |
| |
| return 0; |
| } |
| |
| static int dw_eth_recv(struct eth_device *dev) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| u32 desc_num = priv->rx_currdescnum; |
| struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num]; |
| |
| u32 status = desc_p->txrx_status; |
| int length = 0; |
| |
| /* Check if the owner is the CPU */ |
| if (!(status & DESC_RXSTS_OWNBYDMA)) { |
| |
| length = (status & DESC_RXSTS_FRMLENMSK) >> \ |
| DESC_RXSTS_FRMLENSHFT; |
| |
| NetReceive(desc_p->dmamac_addr, length); |
| |
| /* |
| * Make the current descriptor valid again and go to |
| * the next one |
| */ |
| desc_p->txrx_status |= DESC_RXSTS_OWNBYDMA; |
| |
| /* Test the wrap-around condition. */ |
| if (++desc_num >= CONFIG_RX_DESCR_NUM) |
| desc_num = 0; |
| } |
| |
| priv->rx_currdescnum = desc_num; |
| |
| return length; |
| } |
| |
| static void dw_eth_halt(struct eth_device *dev) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| |
| mac_reset(dev); |
| priv->tx_currdescnum = priv->rx_currdescnum = 0; |
| } |
| |
| static int eth_mdio_read(struct eth_device *dev, u8 addr, u8 reg, u16 *val) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| struct eth_mac_regs *mac_p = priv->mac_regs_p; |
| ulong start; |
| u32 miiaddr; |
| int timeout = CONFIG_MDIO_TIMEOUT; |
| |
| miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | \ |
| ((reg << MIIREGSHIFT) & MII_REGMSK); |
| |
| writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr); |
| |
| start = get_timer(0); |
| while (get_timer(start) < timeout) { |
| if (!(readl(&mac_p->miiaddr) & MII_BUSY)) { |
| *val = readl(&mac_p->miidata); |
| return 0; |
| } |
| |
| /* Try again after 10usec */ |
| udelay(10); |
| }; |
| |
| return -1; |
| } |
| |
| static int eth_mdio_write(struct eth_device *dev, u8 addr, u8 reg, u16 val) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| struct eth_mac_regs *mac_p = priv->mac_regs_p; |
| ulong start; |
| u32 miiaddr; |
| int ret = -1, timeout = CONFIG_MDIO_TIMEOUT; |
| u16 value; |
| |
| writel(val, &mac_p->miidata); |
| miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | \ |
| ((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE; |
| |
| writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr); |
| |
| start = get_timer(0); |
| while (get_timer(start) < timeout) { |
| if (!(readl(&mac_p->miiaddr) & MII_BUSY)) { |
| ret = 0; |
| break; |
| } |
| |
| /* Try again after 10usec */ |
| udelay(10); |
| }; |
| |
| /* Needed as a fix for ST-Phy */ |
| eth_mdio_read(dev, addr, reg, &value); |
| |
| return ret; |
| } |
| |
| #if defined(CONFIG_DW_SEARCH_PHY) |
| static int find_phy(struct eth_device *dev) |
| { |
| int phy_addr = 0; |
| u16 ctrl, oldctrl; |
| |
| do { |
| eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl); |
| oldctrl = ctrl & BMCR_ANENABLE; |
| |
| ctrl ^= BMCR_ANENABLE; |
| eth_mdio_write(dev, phy_addr, MII_BMCR, ctrl); |
| eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl); |
| ctrl &= BMCR_ANENABLE; |
| |
| if (ctrl == oldctrl) { |
| phy_addr++; |
| } else { |
| ctrl ^= BMCR_ANENABLE; |
| eth_mdio_write(dev, phy_addr, MII_BMCR, ctrl); |
| |
| return phy_addr; |
| } |
| } while (phy_addr < 32); |
| |
| return -1; |
| } |
| #endif |
| |
| static int dw_reset_phy(struct eth_device *dev) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| u16 ctrl; |
| ulong start; |
| int timeout = CONFIG_PHYRESET_TIMEOUT; |
| u32 phy_addr = priv->address; |
| |
| eth_mdio_write(dev, phy_addr, MII_BMCR, BMCR_RESET); |
| |
| start = get_timer(0); |
| while (get_timer(start) < timeout) { |
| eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl); |
| if (!(ctrl & BMCR_RESET)) |
| break; |
| |
| /* Try again after 10usec */ |
| udelay(10); |
| }; |
| |
| if (get_timer(start) >= CONFIG_PHYRESET_TIMEOUT) |
| return -1; |
| |
| #ifdef CONFIG_PHY_RESET_DELAY |
| udelay(CONFIG_PHY_RESET_DELAY); |
| #endif |
| return 0; |
| } |
| |
| /* |
| * Add weak default function for board specific PHY configuration |
| */ |
| int __weak designware_board_phy_init(struct eth_device *dev, int phy_addr, |
| int (*mii_write)(struct eth_device *, u8, u8, u16), |
| int dw_reset_phy(struct eth_device *)) |
| { |
| return 0; |
| } |
| |
| static int configure_phy(struct eth_device *dev) |
| { |
| struct dw_eth_dev *priv = dev->priv; |
| int phy_addr; |
| u16 bmcr; |
| #if defined(CONFIG_DW_AUTONEG) |
| u16 bmsr; |
| u32 timeout; |
| ulong start; |
| #endif |
| |
| #if defined(CONFIG_DW_SEARCH_PHY) |
| phy_addr = find_phy(dev); |
| if (phy_addr >= 0) |
| priv->address = phy_addr; |
| else |
| return -1; |
| #else |
| phy_addr = priv->address; |
| #endif |
| |
| /* |
| * Some boards need board specific PHY initialization. This is |
| * after the main driver init code but before the auto negotiation |
| * is run. |
| */ |
| if (designware_board_phy_init(dev, phy_addr, |
| eth_mdio_write, dw_reset_phy) < 0) |
| return -1; |
| |
| if (dw_reset_phy(dev) < 0) |
| return -1; |
| |
| #if defined(CONFIG_DW_AUTONEG) |
| /* Set Auto-Neg Advertisement capabilities to 10/100 half/full */ |
| eth_mdio_write(dev, phy_addr, MII_ADVERTISE, 0x1E1); |
| |
| bmcr = BMCR_ANENABLE | BMCR_ANRESTART; |
| #else |
| bmcr = BMCR_SPEED100 | BMCR_FULLDPLX; |
| |
| #if defined(CONFIG_DW_SPEED10M) |
| bmcr &= ~BMCR_SPEED100; |
| #endif |
| #if defined(CONFIG_DW_DUPLEXHALF) |
| bmcr &= ~BMCR_FULLDPLX; |
| #endif |
| #endif |
| if (eth_mdio_write(dev, phy_addr, MII_BMCR, bmcr) < 0) |
| return -1; |
| |
| /* Read the phy status register and populate priv structure */ |
| #if defined(CONFIG_DW_AUTONEG) |
| timeout = CONFIG_AUTONEG_TIMEOUT; |
| start = get_timer(0); |
| puts("Waiting for PHY auto negotiation to complete"); |
| while (get_timer(start) < timeout) { |
| eth_mdio_read(dev, phy_addr, MII_BMSR, &bmsr); |
| if (bmsr & BMSR_ANEGCOMPLETE) { |
| priv->phy_configured = 1; |
| break; |
| } |
| |
| /* Print dot all 1s to show progress */ |
| if ((get_timer(start) % 1000) == 0) |
| putc('.'); |
| |
| /* Try again after 1msec */ |
| udelay(1000); |
| }; |
| |
| if (!(bmsr & BMSR_ANEGCOMPLETE)) |
| puts(" TIMEOUT!\n"); |
| else |
| puts(" done\n"); |
| #else |
| priv->phy_configured = 1; |
| #endif |
| |
| priv->speed = miiphy_speed(dev->name, phy_addr); |
| priv->duplex = miiphy_duplex(dev->name, phy_addr); |
| |
| return 0; |
| } |
| |
| #if defined(CONFIG_MII) |
| static int dw_mii_read(const char *devname, u8 addr, u8 reg, u16 *val) |
| { |
| struct eth_device *dev; |
| |
| dev = eth_get_dev_by_name(devname); |
| if (dev) |
| eth_mdio_read(dev, addr, reg, val); |
| |
| return 0; |
| } |
| |
| static int dw_mii_write(const char *devname, u8 addr, u8 reg, u16 val) |
| { |
| struct eth_device *dev; |
| |
| dev = eth_get_dev_by_name(devname); |
| if (dev) |
| eth_mdio_write(dev, addr, reg, val); |
| |
| return 0; |
| } |
| #endif |
| |
| int designware_initialize(u32 id, ulong base_addr, u32 phy_addr, u32 interface) |
| { |
| struct eth_device *dev; |
| struct dw_eth_dev *priv; |
| |
| dev = (struct eth_device *) malloc(sizeof(struct eth_device)); |
| if (!dev) |
| return -ENOMEM; |
| |
| /* |
| * Since the priv structure contains the descriptors which need a strict |
| * buswidth alignment, memalign is used to allocate memory |
| */ |
| priv = (struct dw_eth_dev *) memalign(16, sizeof(struct dw_eth_dev)); |
| if (!priv) { |
| free(dev); |
| return -ENOMEM; |
| } |
| |
| memset(dev, 0, sizeof(struct eth_device)); |
| memset(priv, 0, sizeof(struct dw_eth_dev)); |
| |
| sprintf(dev->name, "mii%d", id); |
| dev->iobase = (int)base_addr; |
| dev->priv = priv; |
| |
| eth_getenv_enetaddr_by_index("eth", id, &dev->enetaddr[0]); |
| |
| priv->dev = dev; |
| priv->mac_regs_p = (struct eth_mac_regs *)base_addr; |
| priv->dma_regs_p = (struct eth_dma_regs *)(base_addr + |
| DW_DMA_BASE_OFFSET); |
| priv->address = phy_addr; |
| priv->phy_configured = 0; |
| priv->interface = interface; |
| |
| dev->init = dw_eth_init; |
| dev->send = dw_eth_send; |
| dev->recv = dw_eth_recv; |
| dev->halt = dw_eth_halt; |
| dev->write_hwaddr = dw_write_hwaddr; |
| |
| eth_register(dev); |
| |
| #if defined(CONFIG_MII) |
| miiphy_register(dev->name, dw_mii_read, dw_mii_write); |
| #endif |
| return 1; |
| } |