include/configs/makalu.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (c) 2008 Nuovation System Designs, LLC
  *   Grant Erickson <gerickson@nuovations.com>
  *
  * (C) Copyright 2007-2008
  * Stefan Roese, DENX Software Engineering, sr@denx.de.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /************************************************************************
  * makalu.h - configuration for AMCC Makalu (405EX)
  ***********************************************************************/

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*-----------------------------------------------------------------------
  * High Level Configuration Options
  *----------------------------------------------------------------------*/
 #define CONFIG_MAKALU		1		/* Board is Makalu	*/
 #define CONFIG_405EX		1		/* Specifc 405EX support*/
 #define CONFIG_SYS_CLK_FREQ	33330000	/* ext frequency to pll	*/

 #define	CONFIG_SYS_TEXT_BASE	0xFFFA0000

 /*
  * Include common defines/options for all AMCC eval boards
  */
 #define CONFIG_HOSTNAME	makalu
 #define CONFIG_ADDMISC	"addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"
 #include "amcc-common.h"

 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
 #define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/

 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_FLASH_BASE		0xFC000000
 #define CONFIG_SYS_FPGA_BASE		0xF0000000

 /*-----------------------------------------------------------------------
  * Initial RAM & Stack Pointer Configuration Options
  *
  *   There are traditionally three options for the primordial
  *   (i.e. initial) stack usage on the 405-series:
  *
  *      1) On-chip Memory (OCM) (i.e. SRAM)
  *      2) Data cache
  *      3) SDRAM
  *
  *   For the 405EX(r), there is no OCM, so we are left with (2) or (3)
  *   the latter of which is less than desireable since it requires
  *   setting up the SDRAM and ECC in assembly code.
  *
  *   To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip
  *   select on the External Bus Controller (EBC) and then select a
  *   value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid,
  *   physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and
  *   select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid,
  *   physical SDRAM to use (3).
  *-----------------------------------------------------------------------*/

 #define CONFIG_SYS_INIT_DCACHE_CS	4

 #if defined(CONFIG_SYS_INIT_DCACHE_CS)
 #define CONFIG_SYS_INIT_RAM_ADDR	(CONFIG_SYS_SDRAM_BASE + ( 1 << 30))	/*  1 GiB */
 #else
 #define CONFIG_SYS_INIT_RAM_ADDR	(CONFIG_SYS_SDRAM_BASE + (32 << 20))	/* 32 MiB */
 #endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */

 #define CONFIG_SYS_INIT_RAM_SIZE        (4 << 10)			/*  4 KiB */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

 /*
  * If the data cache is being used for the primordial stack and global
  * data area, the POST word must be placed somewhere else. The General
  * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
  * its compare and mask register contents across reset, so it is used
  * for the POST word.
  */

 #if defined(CONFIG_SYS_INIT_DCACHE_CS)
 # define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 # define CONFIG_SYS_POST_WORD_ADDR	(CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
 #else
 # define CONFIG_SYS_INIT_EXTRA_SIZE	16
 # define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE)
 # define CONFIG_SYS_OCM_DATA_ADDR	CONFIG_SYS_INIT_RAM_ADDR
 #endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */

 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CONFIG_CONS_INDEX	1	/* Use UART0			*/
 #undef CONFIG_SYS_EXT_SERIAL_CLOCK			/* no ext. clk		*/

 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
 #define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/

 /*-----------------------------------------------------------------------
  * FLASH related
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_FLASH_CFI			/* The flash is CFI compatible	*/
 #define CONFIG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/

 #define CONFIG_SYS_FLASH_BANKS_LIST    {CONFIG_SYS_FLASH_BASE}
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/

 #define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
 #define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */

 #ifdef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector	*/
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
 #define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
 #endif /* CONFIG_ENV_IS_IN_FLASH */

 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_MBYTES_SDRAM        (256)		/* 256MB			*/

 #define	CONFIG_SYS_SDRAM0_MB0CF_BASE	((  0 << 20) + CONFIG_SYS_SDRAM_BASE)
 #define	CONFIG_SYS_SDRAM0_MB1CF_BASE	((128 << 20) + CONFIG_SYS_SDRAM_BASE)

 /* DDR1/2 SDRAM Device Control Register Data Values */
 #define CONFIG_SYS_SDRAM0_MB0CF	((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3)	| \
 				 SDRAM_RXBAS_SDSZ_128MB 	| \
 				 SDRAM_RXBAS_SDAM_MODE2 	| \
 				 SDRAM_RXBAS_SDBE_ENABLE)
 #define CONFIG_SYS_SDRAM0_MB1CF	((CONFIG_SYS_SDRAM0_MB1CF_BASE >> 3)	| \
 				 SDRAM_RXBAS_SDSZ_128MB 	| \
 				 SDRAM_RXBAS_SDAM_MODE2 	| \
 				 SDRAM_RXBAS_SDBE_ENABLE)
 #define CONFIG_SYS_SDRAM0_MB2CF	SDRAM_RXBAS_SDBE_DISABLE
 #define CONFIG_SYS_SDRAM0_MB3CF	SDRAM_RXBAS_SDBE_DISABLE
 #define CONFIG_SYS_SDRAM0_MCOPT1	0x04322000
 #define CONFIG_SYS_SDRAM0_MCOPT2	0x00000000
 #define CONFIG_SYS_SDRAM0_MODT0	0x01800000
 #define CONFIG_SYS_SDRAM0_MODT1	0x00000000
 #define CONFIG_SYS_SDRAM0_CODT		0x0080f837
 #define CONFIG_SYS_SDRAM0_RTR		0x06180000
 #define CONFIG_SYS_SDRAM0_INITPLR0	0xa8380000
 #define CONFIG_SYS_SDRAM0_INITPLR1	0x81900400
 #define CONFIG_SYS_SDRAM0_INITPLR2	0x81020000
 #define CONFIG_SYS_SDRAM0_INITPLR3	0x81030000
 #define CONFIG_SYS_SDRAM0_INITPLR4	0x81010404
 #define CONFIG_SYS_SDRAM0_INITPLR5	0x81000542
 #define CONFIG_SYS_SDRAM0_INITPLR6	0x81900400
 #define CONFIG_SYS_SDRAM0_INITPLR7	0x8D080000
 #define CONFIG_SYS_SDRAM0_INITPLR8	0x8D080000
 #define CONFIG_SYS_SDRAM0_INITPLR9	0x8D080000
 #define CONFIG_SYS_SDRAM0_INITPLR10	0x8D080000
 #define CONFIG_SYS_SDRAM0_INITPLR11	0x81000442
 #define CONFIG_SYS_SDRAM0_INITPLR12	0x81010780
 #define CONFIG_SYS_SDRAM0_INITPLR13	0x81010400
 #define CONFIG_SYS_SDRAM0_INITPLR14	0x00000000
 #define CONFIG_SYS_SDRAM0_INITPLR15	0x00000000
 #define CONFIG_SYS_SDRAM0_RQDC		0x80000038
 #define CONFIG_SYS_SDRAM0_RFDC		0x00000209
 #define CONFIG_SYS_SDRAM0_RDCC		0x40000000
 #define CONFIG_SYS_SDRAM0_DLCR		0x030000a5
 #define CONFIG_SYS_SDRAM0_CLKTR	0x80000000
 #define CONFIG_SYS_SDRAM0_WRDTR	0x00000000
 #define CONFIG_SYS_SDRAM0_SDTR1	0x80201000
 #define CONFIG_SYS_SDRAM0_SDTR2	0x32204232
 #define CONFIG_SYS_SDRAM0_SDTR3	0x080b0d1a
 #define CONFIG_SYS_SDRAM0_MMODE	0x00000442
 #define CONFIG_SYS_SDRAM0_MEMODE	0x00000404

 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000

 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	6	/* 24C02 requires 5ms delay */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x52	/* I2C boot EEPROM (24C02BN)	*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/

 /* Standard DTT sensor configuration */
 #define CONFIG_DTT_DS1775	1
 #define CONFIG_DTT_SENSORS	{ 0 }
 #define CONFIG_SYS_I2C_DTT_ADDR	0x48

 /* RTC configuration */
 #define CONFIG_RTC_X1205	1
 #define CONFIG_SYS_I2C_RTC_ADDR	0x6f

 /*-----------------------------------------------------------------------
  * Ethernet
  *----------------------------------------------------------------------*/
 #define CONFIG_M88E1111_PHY	1
 #define CONFIG_IBM_EMAC4_V4	1
 #define CONFIG_EMAC_PHY_MODE	EMAC_PHY_MODE_RGMII_RGMII
 #define CONFIG_PHY_ADDR		6	/* PHY address, See schematics	*/

 #define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */

 #define CONFIG_HAS_ETH0		1

 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
 #define CONFIG_PHY1_ADDR	0

 /*
  * Default environment variables
  */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	CONFIG_AMCC_DEF_ENV						\
 	CONFIG_AMCC_DEF_ENV_POWERPC					\
 	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
 	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"fdt_addr=fc1e0000\0"						\
 	"ramdisk_addr=fc200000\0"					\
 	"pciconfighost=1\0"						\
 	"pcie_mode=RP:RP\0"						\
 	""

 /*
  * Commands additional to the ones defined in amcc-common.h
  */
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DTT
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SNTP

 /* POST support */
 #define CONFIG_POST		(CONFIG_SYS_POST_CACHE		| \
 				 CONFIG_SYS_POST_CPU		| \
 				 CONFIG_SYS_POST_ETHER		| \
 				 CONFIG_SYS_POST_I2C		| \
 				 CONFIG_SYS_POST_MEMORY	| \
 				 CONFIG_SYS_POST_UART)

 /* Define here the base-addresses of the UARTs to test in POST */
 #define CONFIG_SYS_POST_UART_TABLE	{ CONFIG_SYS_NS16550_COM1, \
 			CONFIG_SYS_NS16550_COM2 }

 #define CONFIG_LOGBUFFER
 #define CONFIG_SYS_POST_CACHE_ADDR	0x00800000 /* free virtual address	*/

 #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */

 /*-----------------------------------------------------------------------
  * PCI stuff
  *----------------------------------------------------------------------*/
 #define CONFIG_PCI			/* include pci support	        */
 #define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
 #define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
 #define CONFIG_PCI_CONFIG_HOST_BRIDGE

 /*-----------------------------------------------------------------------
  * PCIe stuff
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_PCIE_MEMBASE	0x90000000	/* mapped PCIe memory	*/
 #define CONFIG_SYS_PCIE_MEMSIZE	0x08000000      /* 128 Meg, smallest incr per port */

 #define	CONFIG_SYS_PCIE0_CFGBASE	0xa0000000      /* remote access */
 #define	CONFIG_SYS_PCIE0_XCFGBASE	0xb0000000      /* local access */
 #define	CONFIG_SYS_PCIE0_CFGMASK	0xe0000001      /* 512 Meg */

 #define	CONFIG_SYS_PCIE1_CFGBASE	0xc0000000      /* remote access */
 #define	CONFIG_SYS_PCIE1_XCFGBASE	0xd0000000      /* local access */
 #define	CONFIG_SYS_PCIE1_CFGMASK	0xe0000001      /* 512 Meg */

 #define	CONFIG_SYS_PCIE0_UTLBASE	0xef502000
 #define	CONFIG_SYS_PCIE1_UTLBASE	0xef503000

 /* base address of inbound PCIe window */
 #define CONFIG_SYS_PCIE_INBOUND_BASE	0x0000000000000000ULL

 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
 #define CONFIG_SYS_EBC_PB0AP		0x08033700
 #define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_FLASH_BASE | 0xda000)

 /* Memory Bank 2 (CPLD) initialization						*/
 #define CONFIG_SYS_EBC_PB2AP           0x9400C800
 #define CONFIG_SYS_EBC_PB2CR           0xF0018000 /*  BAS=0x800,BS=1MB,BU=R/W,BW=8bit	*/

 #define CONFIG_SYS_EBC_CFG		0x7FC00000 /*  EBC0_CFG */

 /*-----------------------------------------------------------------------
  * GPIO Setup
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_4xx_GPIO_TABLE { /*	  Out		  GPIO	Alternate1	Alternate2	Alternate3 */ \
 {											\
 /* GPIO Core 0 */									\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO0	EBC_DATA_PAR(0)			*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO1	EBC_DATA_PAR(1)			*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO2	EBC_DATA_PAR(2)			*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO3	EBC_DATA_PAR(3)			*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO4	EBC_DATA(20)	USB2_DATA(4)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO5	EBC_DATA(21)	USB2_DATA(5)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO6	EBC_DATA(22)	USB2_DATA(6)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO7	EBC_DATA(23)	USB2_DATA(7)	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8	CS(1)/NFCE(1)	IRQ(7)		*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9	CS(2)/NFCE(2)	IRQ(8)		*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3)	IRQ(9)		*/	\
 {GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6)				*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16)	USB2_DATA(0)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17)	USB2_DATA(1)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18)	USB2_DATA(2)	*/	\
 {GPIO0_BASE, GPIO_BI,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19)	USB2_DATA(3)	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD	UART1_CTS	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR	UART1_RTS	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS			*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS			*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO20 UART0_DTR	UART1_TX	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO21 UART0_RI	UART1_RX	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ	DMA_ACK2	*/	\
 {GPIO0_BASE, GPIO_OUT, GPIO_SEL,  GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK	DMA_REQ2	*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ	DMA_EOT2	IRQ(4) */ \
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK	DMA_ACK3	IRQ(3) */ \
 {GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5)	DMA_EOT0	TS(3) */ \
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ	DMA_EOT3	IRQ(5) */ \
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL , GPIO_OUT_0}, /* GPIO28				*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO29 DMA_EOT1	IRQ(2)		*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_SEL,  GPIO_OUT_0}, /* GPIO30 DMA_REQ1	IRQ(1)		*/	\
 {GPIO0_BASE, GPIO_IN,  GPIO_ALT2, GPIO_OUT_0}, /* GPIO31 DMA_ACK1	IRQ(0)		*/	\
 }												\
 }

 #define CONFIG_SYS_GPIO_PCIE_RST	23
 #define CONFIG_SYS_GPIO_PCIE_CLKREQ	27
 #define CONFIG_SYS_GPIO_PCIE_WAKE	28

 #endif	/* __CONFIG_H */
	/*
	* Copyright (c) 2008 Nuovation System Designs, LLC
	* Grant Erickson <gerickson@nuovations.com>
	*
	* (C) Copyright 2007-2008
	* Stefan Roese, DENX Software Engineering, sr@denx.de.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/************************************************************************
	* makalu.h - configuration for AMCC Makalu (405EX)
	***********************************************************************/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*-----------------------------------------------------------------------
	* High Level Configuration Options
	----------------------------------------------------------------------/
	#define CONFIG_MAKALU 1 /* Board is Makalu */
	#define CONFIG_405EX 1 /* Specifc 405EX support*/
	#define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */

	#define CONFIG_SYS_TEXT_BASE 0xFFFA0000

	/*
	* Include common defines/options for all AMCC eval boards
	*/
	#define CONFIG_HOSTNAME makalu
	#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"
	#include "amcc-common.h"

	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
	#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */

	/*-----------------------------------------------------------------------
	* Base addresses -- Note these are effective addresses where the
	* actual resources get mapped (not physical addresses)
	----------------------------------------------------------------------/
	#define CONFIG_SYS_FLASH_BASE 0xFC000000
	#define CONFIG_SYS_FPGA_BASE 0xF0000000

	/*-----------------------------------------------------------------------
	* Initial RAM & Stack Pointer Configuration Options
	*
	* There are traditionally three options for the primordial
	* (i.e. initial) stack usage on the 405-series:
	*
	* 1) On-chip Memory (OCM) (i.e. SRAM)
	* 2) Data cache
	* 3) SDRAM
	*
	* For the 405EX(r), there is no OCM, so we are left with (2) or (3)
	* the latter of which is less than desireable since it requires
	* setting up the SDRAM and ECC in assembly code.
	*
	* To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip
	* select on the External Bus Controller (EBC) and then select a
	* value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid,
	* physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and
	* select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid,
	* physical SDRAM to use (3).
	-----------------------------------------------------------------------/

	#define CONFIG_SYS_INIT_DCACHE_CS 4

	#if defined(CONFIG_SYS_INIT_DCACHE_CS)
	#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */
	#else
	#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + (32 << 20)) /* 32 MiB */
	#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */

	#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) /* 4 KiB */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

	/*
	* If the data cache is being used for the primordial stack and global
	* data area, the POST word must be placed somewhere else. The General
	* Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
	* its compare and mask register contents across reset, so it is used
	* for the POST word.
	*/

	#if defined(CONFIG_SYS_INIT_DCACHE_CS)
	# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	# define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
	#else
	# define CONFIG_SYS_INIT_EXTRA_SIZE 16
	# define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE)
	# define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_INIT_RAM_ADDR
	#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */

	/*-----------------------------------------------------------------------
	* Serial Port
	----------------------------------------------------------------------/
	#define CONFIG_CONS_INDEX 1 /* Use UART0 */
	#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no ext. clk */

	/*-----------------------------------------------------------------------
	* Environment
	----------------------------------------------------------------------/
	#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */

	/*-----------------------------------------------------------------------
	* FLASH related
	----------------------------------------------------------------------/
	#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
	#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */

	#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */

	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */

	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
	#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */

	#ifdef CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
	#endif /* CONFIG_ENV_IS_IN_FLASH */

	/*-----------------------------------------------------------------------
	* DDR SDRAM
	----------------------------------------------------------------------/
	#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */

	#define CONFIG_SYS_SDRAM0_MB0CF_BASE (( 0 << 20) + CONFIG_SYS_SDRAM_BASE)
	#define CONFIG_SYS_SDRAM0_MB1CF_BASE ((128 << 20) + CONFIG_SYS_SDRAM_BASE)

	/* DDR1/2 SDRAM Device Control Register Data Values */
	#define CONFIG_SYS_SDRAM0_MB0CF ((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3) \| \
	SDRAM_RXBAS_SDSZ_128MB \| \
	SDRAM_RXBAS_SDAM_MODE2 \| \
	SDRAM_RXBAS_SDBE_ENABLE)
	#define CONFIG_SYS_SDRAM0_MB1CF ((CONFIG_SYS_SDRAM0_MB1CF_BASE >> 3) \| \
	SDRAM_RXBAS_SDSZ_128MB \| \
	SDRAM_RXBAS_SDAM_MODE2 \| \
	SDRAM_RXBAS_SDBE_ENABLE)
	#define CONFIG_SYS_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE
	#define CONFIG_SYS_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE
	#define CONFIG_SYS_SDRAM0_MCOPT1 0x04322000
	#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000
	#define CONFIG_SYS_SDRAM0_MODT0 0x01800000
	#define CONFIG_SYS_SDRAM0_MODT1 0x00000000
	#define CONFIG_SYS_SDRAM0_CODT 0x0080f837
	#define CONFIG_SYS_SDRAM0_RTR 0x06180000
	#define CONFIG_SYS_SDRAM0_INITPLR0 0xa8380000
	#define CONFIG_SYS_SDRAM0_INITPLR1 0x81900400
	#define CONFIG_SYS_SDRAM0_INITPLR2 0x81020000
	#define CONFIG_SYS_SDRAM0_INITPLR3 0x81030000
	#define CONFIG_SYS_SDRAM0_INITPLR4 0x81010404
	#define CONFIG_SYS_SDRAM0_INITPLR5 0x81000542
	#define CONFIG_SYS_SDRAM0_INITPLR6 0x81900400
	#define CONFIG_SYS_SDRAM0_INITPLR7 0x8D080000
	#define CONFIG_SYS_SDRAM0_INITPLR8 0x8D080000
	#define CONFIG_SYS_SDRAM0_INITPLR9 0x8D080000
	#define CONFIG_SYS_SDRAM0_INITPLR10 0x8D080000
	#define CONFIG_SYS_SDRAM0_INITPLR11 0x81000442
	#define CONFIG_SYS_SDRAM0_INITPLR12 0x81010780
	#define CONFIG_SYS_SDRAM0_INITPLR13 0x81010400
	#define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000
	#define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000
	#define CONFIG_SYS_SDRAM0_RQDC 0x80000038
	#define CONFIG_SYS_SDRAM0_RFDC 0x00000209
	#define CONFIG_SYS_SDRAM0_RDCC 0x40000000
	#define CONFIG_SYS_SDRAM0_DLCR 0x030000a5
	#define CONFIG_SYS_SDRAM0_CLKTR 0x80000000
	#define CONFIG_SYS_SDRAM0_WRDTR 0x00000000
	#define CONFIG_SYS_SDRAM0_SDTR1 0x80201000
	#define CONFIG_SYS_SDRAM0_SDTR2 0x32204232
	#define CONFIG_SYS_SDRAM0_SDTR3 0x080b0d1a
	#define CONFIG_SYS_SDRAM0_MMODE 0x00000442
	#define CONFIG_SYS_SDRAM0_MEMODE 0x00000404

	/*-----------------------------------------------------------------------
	* I2C
	----------------------------------------------------------------------/
	#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000

	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */

	/* Standard DTT sensor configuration */
	#define CONFIG_DTT_DS1775 1
	#define CONFIG_DTT_SENSORS { 0 }
	#define CONFIG_SYS_I2C_DTT_ADDR 0x48

	/* RTC configuration */
	#define CONFIG_RTC_X1205 1
	#define CONFIG_SYS_I2C_RTC_ADDR 0x6f

	/*-----------------------------------------------------------------------
	* Ethernet
	----------------------------------------------------------------------/
	#define CONFIG_M88E1111_PHY 1
	#define CONFIG_IBM_EMAC4_V4 1
	#define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_RGMII_RGMII
	#define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */

	#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
	#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */

	#define CONFIG_HAS_ETH0 1

	#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
	#define CONFIG_PHY1_ADDR 0

	/*
	* Default environment variables
	*/
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_AMCC_DEF_ENV \
	CONFIG_AMCC_DEF_ENV_POWERPC \
	CONFIG_AMCC_DEF_ENV_PPC_OLD \
	CONFIG_AMCC_DEF_ENV_NOR_UPD \
	"kernel_addr=fc000000\0" \
	"fdt_addr=fc1e0000\0" \
	"ramdisk_addr=fc200000\0" \
	"pciconfighost=1\0" \
	"pcie_mode=RP:RP\0" \
	""

	/*
	* Commands additional to the ones defined in amcc-common.h
	*/
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_DTT
	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_SNTP

	/* POST support */
	#define CONFIG_POST (CONFIG_SYS_POST_CACHE \| \
	CONFIG_SYS_POST_CPU \| \
	CONFIG_SYS_POST_ETHER \| \
	CONFIG_SYS_POST_I2C \| \
	CONFIG_SYS_POST_MEMORY \| \
	CONFIG_SYS_POST_UART)

	/* Define here the base-addresses of the UARTs to test in POST */
	#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \
	CONFIG_SYS_NS16550_COM2 }

	#define CONFIG_LOGBUFFER
	#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */

	#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */

	/*-----------------------------------------------------------------------
	* PCI stuff
	----------------------------------------------------------------------/
	#define CONFIG_PCI /* include pci support */
	#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
	#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
	#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
	#define CONFIG_PCI_CONFIG_HOST_BRIDGE

	/*-----------------------------------------------------------------------
	* PCIe stuff
	----------------------------------------------------------------------/
	#define CONFIG_SYS_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */
	#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */

	#define CONFIG_SYS_PCIE0_CFGBASE 0xa0000000 /* remote access */
	#define CONFIG_SYS_PCIE0_XCFGBASE 0xb0000000 /* local access */
	#define CONFIG_SYS_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */

	#define CONFIG_SYS_PCIE1_CFGBASE 0xc0000000 /* remote access */
	#define CONFIG_SYS_PCIE1_XCFGBASE 0xd0000000 /* local access */
	#define CONFIG_SYS_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */

	#define CONFIG_SYS_PCIE0_UTLBASE 0xef502000
	#define CONFIG_SYS_PCIE1_UTLBASE 0xef503000

	/* base address of inbound PCIe window */
	#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL

	/*-----------------------------------------------------------------------
	* External Bus Controller (EBC) Setup
	----------------------------------------------------------------------/
	/* Memory Bank 0 (NOR-FLASH) initialization */
	#define CONFIG_SYS_EBC_PB0AP 0x08033700
	#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE \| 0xda000)

	/* Memory Bank 2 (CPLD) initialization */
	#define CONFIG_SYS_EBC_PB2AP 0x9400C800
	#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */

	#define CONFIG_SYS_EBC_CFG 0x7FC00000 /* EBC0_CFG */

	/*-----------------------------------------------------------------------
	* GPIO Setup
	----------------------------------------------------------------------/
	#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
	{ \
	/* GPIO Core 0 */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \
	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \
	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \
	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \
	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \
	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 CS(1)/NFCE(1) IRQ(7) */ \
	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 CS(2)/NFCE(2) IRQ(8) */ \
	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 CS(3)/NFCE(3) IRQ(9) */ \
	{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \
	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \
	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \
	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \
	{GPIO0_BASE, GPIO_BI, GPIO_ALT2, GPIO_OUT_0}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \
	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \
	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \
	{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \
	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \
	{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \
	{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO29 DMA_EOT1 IRQ(2) */ \
	{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO30 DMA_REQ1 IRQ(1) */ \
	{GPIO0_BASE, GPIO_IN, GPIO_ALT2, GPIO_OUT_0}, /* GPIO31 DMA_ACK1 IRQ(0) */ \
	} \
	}

	#define CONFIG_SYS_GPIO_PCIE_RST 23
	#define CONFIG_SYS_GPIO_PCIE_CLKREQ 27
	#define CONFIG_SYS_GPIO_PCIE_WAKE 28

	#endif /* __CONFIG_H */