blob: 73215855ccd2659d5e3a2ef4d42a2678be317957 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* Copyright (C) STMicroelectronics 2017 - All Rights Reserved
* Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/stm32mp1-clks.h>
#include <dt-bindings/reset/stm32mp1-resets.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0>;
};
cpu1: cpu@1 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <1>;
};
};
psci {
compatible = "arm,psci-1.0";
method = "smc";
cpu_off = <0x84000002>;
cpu_on = <0x84000003>;
};
aliases {
gpio0 = &gpioa;
gpio1 = &gpiob;
gpio2 = &gpioc;
gpio3 = &gpiod;
gpio4 = &gpioe;
gpio5 = &gpiof;
gpio6 = &gpiog;
gpio7 = &gpioh;
gpio8 = &gpioi;
gpio9 = &gpioj;
gpio10 = &gpiok;
serial0 = &usart1;
serial1 = &usart2;
serial2 = &usart3;
serial3 = &uart4;
serial4 = &uart5;
serial5 = &usart6;
serial6 = &uart7;
serial7 = &uart8;
};
intc: interrupt-controller@a0021000 {
compatible = "arm,cortex-a7-gic";
#interrupt-cells = <3>;
interrupt-controller;
reg = <0xa0021000 0x1000>,
<0xa0022000 0x2000>;
};
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
interrupt-parent = <&intc>;
};
clocks {
clk_hse: clk-hse {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
};
clk_hsi: clk-hsi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <64000000>;
};
clk_lse: clk-lse {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
};
clk_lsi: clk-lsi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32000>;
};
clk_csi: clk-csi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <4000000>;
};
};
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&intc>;
ranges;
timers2: timer@40000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40000000 0x400>;
clocks = <&rcc TIM2_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@1 {
compatible = "st,stm32h7-timer-trigger";
reg = <1>;
status = "disabled";
};
};
timers3: timer@40001000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40001000 0x400>;
clocks = <&rcc TIM3_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@2 {
compatible = "st,stm32h7-timer-trigger";
reg = <2>;
status = "disabled";
};
};
timers4: timer@40002000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40002000 0x400>;
clocks = <&rcc TIM4_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@3 {
compatible = "st,stm32h7-timer-trigger";
reg = <3>;
status = "disabled";
};
};
timers5: timer@40003000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40003000 0x400>;
clocks = <&rcc TIM5_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@4 {
compatible = "st,stm32h7-timer-trigger";
reg = <4>;
status = "disabled";
};
};
timers6: timer@40004000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40004000 0x400>;
clocks = <&rcc TIM6_K>;
clock-names = "int";
status = "disabled";
timer@5 {
compatible = "st,stm32h7-timer-trigger";
reg = <5>;
status = "disabled";
};
};
timers7: timer@40005000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40005000 0x400>;
clocks = <&rcc TIM7_K>;
clock-names = "int";
status = "disabled";
timer@6 {
compatible = "st,stm32h7-timer-trigger";
reg = <6>;
status = "disabled";
};
};
timers12: timer@40006000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40006000 0x400>;
clocks = <&rcc TIM12_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@11 {
compatible = "st,stm32h7-timer-trigger";
reg = <11>;
status = "disabled";
};
};
timers13: timer@40007000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40007000 0x400>;
clocks = <&rcc TIM13_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@12 {
compatible = "st,stm32h7-timer-trigger";
reg = <12>;
status = "disabled";
};
};
timers14: timer@40008000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x40008000 0x400>;
clocks = <&rcc TIM14_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@13 {
compatible = "st,stm32h7-timer-trigger";
reg = <13>;
status = "disabled";
};
};
lptimer1: timer@40009000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-lptimer";
reg = <0x40009000 0x400>;
clocks = <&rcc LPTIM1_K>;
clock-names = "mux";
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
trigger@0 {
compatible = "st,stm32-lptimer-trigger";
reg = <0>;
status = "disabled";
};
counter {
compatible = "st,stm32-lptimer-counter";
status = "disabled";
};
};
spi2: spi@4000b000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x4000b000 0x400>;
interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI2_K>;
resets = <&rcc SPI2_R>;
dmas = <&dmamux1 39 0x400 0x05>,
<&dmamux1 40 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
spi3: spi@4000c000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x4000c000 0x400>;
interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI3_K>;
resets = <&rcc SPI3_R>;
dmas = <&dmamux1 61 0x400 0x05>,
<&dmamux1 62 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
usart2: serial@4000e000 {
compatible = "st,stm32h7-uart";
reg = <0x4000e000 0x400>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc USART2_K>;
status = "disabled";
};
usart3: serial@4000f000 {
compatible = "st,stm32h7-uart";
reg = <0x4000f000 0x400>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc USART3_K>;
status = "disabled";
};
uart4: serial@40010000 {
compatible = "st,stm32h7-uart";
reg = <0x40010000 0x400>;
interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc UART4_K>;
status = "disabled";
};
uart5: serial@40011000 {
compatible = "st,stm32h7-uart";
reg = <0x40011000 0x400>;
interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc UART5_K>;
status = "disabled";
};
i2c1: i2c@40012000 {
compatible = "st,stm32f7-i2c";
reg = <0x40012000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C1_K>;
resets = <&rcc I2C1_R>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c2: i2c@40013000 {
compatible = "st,stm32f7-i2c";
reg = <0x40013000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C2_K>;
resets = <&rcc I2C2_R>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c3: i2c@40014000 {
compatible = "st,stm32f7-i2c";
reg = <0x40014000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C3_K>;
resets = <&rcc I2C3_R>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c5: i2c@40015000 {
compatible = "st,stm32f7-i2c";
reg = <0x40015000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C5_K>;
resets = <&rcc I2C5_R>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
cec: cec@40016000 {
compatible = "st,stm32-cec";
reg = <0x40016000 0x400>;
interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc CEC_K>, <&clk_lse>;
clock-names = "cec", "hdmi-cec";
status = "disabled";
};
dac: dac@40017000 {
compatible = "st,stm32h7-dac-core";
reg = <0x40017000 0x400>;
clocks = <&rcc DAC12>;
clock-names = "pclk";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
dac1: dac@1 {
compatible = "st,stm32-dac";
#io-channels-cells = <1>;
reg = <1>;
status = "disabled";
};
dac2: dac@2 {
compatible = "st,stm32-dac";
#io-channels-cells = <1>;
reg = <2>;
status = "disabled";
};
};
uart7: serial@40018000 {
compatible = "st,stm32h7-uart";
reg = <0x40018000 0x400>;
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc UART7_K>;
status = "disabled";
};
uart8: serial@40019000 {
compatible = "st,stm32h7-uart";
reg = <0x40019000 0x400>;
interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc UART8_K>;
status = "disabled";
};
timers1: timer@44000000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44000000 0x400>;
clocks = <&rcc TIM1_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@0 {
compatible = "st,stm32h7-timer-trigger";
reg = <0>;
status = "disabled";
};
};
timers8: timer@44001000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44001000 0x400>;
clocks = <&rcc TIM8_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@7 {
compatible = "st,stm32h7-timer-trigger";
reg = <7>;
status = "disabled";
};
};
usart6: serial@44003000 {
compatible = "st,stm32h7-uart";
reg = <0x44003000 0x400>;
interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc USART6_K>;
status = "disabled";
};
spi1: spi@44004000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x44004000 0x400>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI1_K>;
resets = <&rcc SPI1_R>;
dmas = <&dmamux1 37 0x400 0x05>,
<&dmamux1 38 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
spi4: spi@44005000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x44005000 0x400>;
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI4_K>;
resets = <&rcc SPI4_R>;
dmas = <&dmamux1 83 0x400 0x05>,
<&dmamux1 84 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
timers15: timer@44006000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44006000 0x400>;
clocks = <&rcc TIM15_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@14 {
compatible = "st,stm32h7-timer-trigger";
reg = <14>;
status = "disabled";
};
};
timers16: timer@44007000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44007000 0x400>;
clocks = <&rcc TIM16_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@15 {
compatible = "st,stm32h7-timer-trigger";
reg = <15>;
status = "disabled";
};
};
timers17: timer@44008000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-timers";
reg = <0x44008000 0x400>;
clocks = <&rcc TIM17_K>;
clock-names = "int";
status = "disabled";
pwm {
compatible = "st,stm32-pwm";
status = "disabled";
};
timer@16 {
compatible = "st,stm32h7-timer-trigger";
reg = <16>;
status = "disabled";
};
};
spi5: spi@44009000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x44009000 0x400>;
interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI5_K>;
resets = <&rcc SPI5_R>;
dmas = <&dmamux1 85 0x400 0x05>,
<&dmamux1 86 0x400 0x05>;
dma-names = "rx", "tx";
status = "disabled";
};
dfsdm: dfsdm@4400d000 {
compatible = "st,stm32mp1-dfsdm";
reg = <0x4400d000 0x800>;
clocks = <&rcc DFSDM_K>;
clock-names = "dfsdm";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
dfsdm0: filter@0 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <0>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 101 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm1: filter@1 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <1>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 102 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm2: filter@2 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <2>;
interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 103 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm3: filter@3 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <3>;
interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 104 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm4: filter@4 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <4>;
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 91 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
dfsdm5: filter@5 {
compatible = "st,stm32-dfsdm-adc";
#io-channel-cells = <1>;
reg = <5>;
interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmamux1 92 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
};
m_can1: can@4400e000 {
compatible = "bosch,m_can";
reg = <0x4400e000 0x400>, <0x44011000 0x2800>;
reg-names = "m_can", "message_ram";
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "int0", "int1";
clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
clock-names = "hclk", "cclk";
bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
status = "disabled";
};
m_can2: can@4400f000 {
compatible = "bosch,m_can";
reg = <0x4400f000 0x400>, <0x44011000 0x2800>;
reg-names = "m_can", "message_ram";
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "int0", "int1";
clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
clock-names = "hclk", "cclk";
bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
status = "disabled";
};
dma1: dma@48000000 {
compatible = "st,stm32-dma";
reg = <0x48000000 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA1>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
};
dma2: dma@48001000 {
compatible = "st,stm32-dma";
reg = <0x48001000 0x400>;
interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA2>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
};
dmamux1: dma-router@48002000 {
compatible = "st,stm32h7-dmamux";
reg = <0x48002000 0x1c>;
#dma-cells = <3>;
dma-requests = <128>;
dma-masters = <&dma1 &dma2>;
dma-channels = <16>;
clocks = <&rcc DMAMUX>;
};
adc: adc@48003000 {
compatible = "st,stm32mp1-adc-core";
reg = <0x48003000 0x400>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc ADC12>, <&rcc ADC12_K>;
clock-names = "bus", "adc";
interrupt-controller;
#interrupt-cells = <1>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
adc1: adc@0 {
compatible = "st,stm32mp1-adc";
#io-channel-cells = <1>;
reg = <0x0>;
interrupt-parent = <&adc>;
interrupts = <0>;
dmas = <&dmamux1 9 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
adc2: adc@100 {
compatible = "st,stm32mp1-adc";
#io-channel-cells = <1>;
reg = <0x100>;
interrupt-parent = <&adc>;
interrupts = <1>;
dmas = <&dmamux1 10 0x400 0x01>;
dma-names = "rx";
status = "disabled";
};
};
sdmmc3: sdmmc@48004000 {
compatible = "st,stm32-sdmmc2";
reg = <0x48004000 0x400>, <0x48005000 0x400>;
reg-names = "sdmmc", "delay";
interrupts = <GIC_SPI 137 IRQ_TYPE_NONE>;
clocks = <&rcc SDMMC3_K>;
resets = <&rcc SDMMC3_R>;
st,idma = <1>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <120000000>;
status = "disabled";
};
usbotg_hs: usb-otg@49000000 {
compatible = "st,stm32mp1-hsotg", "snps,dwc2";
reg = <0x49000000 0x10000>;
clocks = <&rcc USBO_K>;
clock-names = "otg";
resets = <&rcc USBO_R>;
reset-names = "dwc2";
interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
g-rx-fifo-size = <256>;
g-np-tx-fifo-size = <32>;
g-tx-fifo-size = <128 128 64 64 64 64 32 32>;
dr_mode = "otg";
usb33d-supply = <&usb33>;
status = "disabled";
};
hwspinlock: hwspinlock@4c000000 {
compatible = "st,stm32-hwspinlock";
#hwlock-cells = <1>;
reg = <0x4c000000 0x400>;
clocks = <&rcc HSEM>;
clock-names = "hwspinlock";
status = "disabled";
};
rcc: rcc@50000000 {
compatible = "st,stm32mp1-rcc", "syscon";
reg = <0x50000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
rcc_reboot: rcc-reboot@50000000 {
compatible = "syscon-reboot";
regmap = <&rcc>;
offset = <0x404>;
mask = <0x1>;
};
pwr: pwr@50001000 {
compatible = "st,stm32mp1-pwr", "st,stm32-pwr", "syscon", "simple-mfd";
reg = <0x50001000 0x400>;
system-power-controller;
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
st,sysrcc = <&rcc>;
clocks = <&rcc PLL2_R>;
clock-names = "phyclk";
pwr-regulators@c {
compatible = "st,stm32mp1,pwr-reg";
st,tzcr = <&rcc 0x0 0x1>;
reg11: reg11 {
regulator-name = "reg11";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
reg18: reg18 {
regulator-name = "reg18";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
usb33: usb33 {
regulator-name = "usb33";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
};
};
exti: interrupt-controller@5000d000 {
compatible = "st,stm32mp1-exti", "syscon";
interrupt-controller;
#interrupt-cells = <2>;
reg = <0x5000d000 0x400>;
};
syscfg: syscon@50020000 {
compatible = "st,stm32mp157-syscfg", "syscon";
reg = <0x50020000 0x400>;
};
lptimer2: timer@50021000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-lptimer";
reg = <0x50021000 0x400>;
clocks = <&rcc LPTIM2_K>;
clock-names = "mux";
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
trigger@1 {
compatible = "st,stm32-lptimer-trigger";
reg = <1>;
status = "disabled";
};
counter {
compatible = "st,stm32-lptimer-counter";
status = "disabled";
};
};
lptimer3: timer@50022000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32-lptimer";
reg = <0x50022000 0x400>;
clocks = <&rcc LPTIM3_K>;
clock-names = "mux";
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
trigger@2 {
compatible = "st,stm32-lptimer-trigger";
reg = <2>;
status = "disabled";
};
};
lptimer4: timer@50023000 {
compatible = "st,stm32-lptimer";
reg = <0x50023000 0x400>;
clocks = <&rcc LPTIM4_K>;
clock-names = "mux";
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
};
lptimer5: timer@50024000 {
compatible = "st,stm32-lptimer";
reg = <0x50024000 0x400>;
clocks = <&rcc LPTIM5_K>;
clock-names = "mux";
status = "disabled";
pwm {
compatible = "st,stm32-pwm-lp";
#pwm-cells = <3>;
status = "disabled";
};
};
vrefbuf: vrefbuf@50025000 {
compatible = "st,stm32-vrefbuf";
reg = <0x50025000 0x8>;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <2500000>;
clocks = <&rcc VREF>;
status = "disabled";
};
cryp1: cryp@54001000 {
compatible = "st,stm32mp1-cryp";
reg = <0x54001000 0x400>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc CRYP1>;
resets = <&rcc CRYP1_R>;
status = "disabled";
};
hash1: hash@54002000 {
compatible = "st,stm32f756-hash";
reg = <0x54002000 0x400>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc HASH1>;
resets = <&rcc HASH1_R>;
dmas = <&mdma1 31 0x10 0x1000A02 0x0 0x0>;
dma-names = "in";
dma-maxburst = <2>;
status = "disabled";
};
rng1: rng@54003000 {
compatible = "st,stm32-rng";
reg = <0x54003000 0x400>;
clocks = <&rcc RNG1_K>;
resets = <&rcc RNG1_R>;
status = "disabled";
};
mdma1: dma@58000000 {
compatible = "st,stm32h7-mdma";
reg = <0x58000000 0x1000>;
interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc MDMA>;
#dma-cells = <5>;
dma-channels = <32>;
dma-requests = <48>;
};
fmc: nand-controller@58002000 {
compatible = "st,stm32mp15-fmc2";
reg = <0x58002000 0x1000>,
<0x80000000 0x1000>,
<0x88010000 0x1000>,
<0x88020000 0x1000>,
<0x81000000 0x1000>,
<0x89010000 0x1000>,
<0x89020000 0x1000>;
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc FMC_K>;
resets = <&rcc FMC_R>;
status = "disabled";
};
qspi: spi@58003000 {
compatible = "st,stm32f469-qspi";
reg = <0x58003000 0x1000>, <0x70000000 0x10000000>;
reg-names = "qspi", "qspi_mm";
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc QSPI_K>;
resets = <&rcc QSPI_R>;
status = "disabled";
};
sdmmc1: sdmmc@58005000 {
compatible = "st,stm32-sdmmc2";
reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
reg-names = "sdmmc", "delay";
clocks = <&rcc SDMMC1_K>;
resets = <&rcc SDMMC1_R>;
st,idma = <1>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <120000000>;
status = "disabled";
};
sdmmc2: sdmmc@58007000 {
compatible = "st,stm32-sdmmc2";
reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
reg-names = "sdmmc", "delay";
interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>;
clocks = <&rcc SDMMC2_K>;
resets = <&rcc SDMMC2_R>;
st,idma = <1>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <120000000>;
status = "disabled";
};
crc1: crc@58009000 {
compatible = "st,stm32f7-crc";
reg = <0x58009000 0x400>;
clocks = <&rcc CRC1>;
status = "disabled";
};
stmmac_axi_config_0: stmmac-axi-config {
snps,wr_osr_lmt = <0x7>;
snps,rd_osr_lmt = <0x7>;
snps,blen = <0 0 0 0 16 8 4>;
};
ethernet0: ethernet@5800a000 {
compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
reg = <0x5800a000 0x2000>;
reg-names = "stmmaceth";
interrupts-extended =
<&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
<&intc GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
<&exti 70 1>;
interrupt-names = "macirq",
"eth_wake_irq",
"stm32_pwr_wakeup";
clock-names = "stmmaceth",
"mac-clk-tx",
"mac-clk-rx",
"ethstp";
clocks = <&rcc ETHMAC>,
<&rcc ETHTX>,
<&rcc ETHRX>,
<&rcc ETHSTP>;
st,syscon = <&syscfg 0x4>;
snps,mixed-burst;
snps,pbl = <2>;
snps,en-tx-lpi-clockgating;
snps,axi-config = <&stmmac_axi_config_0>;
snps,tso;
status = "disabled";
};
usbh_ohci: usbh-ohci@5800c000 {
compatible = "generic-ohci";
reg = <0x5800c000 0x1000>;
clocks = <&rcc USBH>;
resets = <&rcc USBH_R>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
usbh_ehci: usbh-ehci@5800d000 {
compatible = "generic-ehci";
reg = <0x5800d000 0x1000>;
clocks = <&rcc USBH>;
resets = <&rcc USBH_R>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
companion = <&usbh_ohci>;
status = "disabled";
};
dsi: dsi@5a000000 {
compatible = "st,stm32-dsi";
reg = <0x5a000000 0x800>;
clocks = <&rcc DSI_K>, <&clk_hse>, <&rcc DSI_PX>;
clock-names = "pclk", "ref", "px_clk";
resets = <&rcc DSI_R>;
reset-names = "apb";
status = "disabled";
};
ltdc: display-controller@5a001000 {
compatible = "st,stm32-ltdc";
reg = <0x5a001000 0x400>;
interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc LTDC_PX>;
clock-names = "lcd";
resets = <&rcc LTDC_R>;
status = "disabled";
};
iwdg2: watchdog@5a002000 {
compatible = "st,stm32mp1-iwdg";
reg = <0x5a002000 0x400>;
clocks = <&rcc IWDG2>, <&rcc CK_LSI>;
clock-names = "pclk", "lsi";
status = "disabled";
};
usbphyc: usbphyc@5a006000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32mp1-usbphyc";
reg = <0x5a006000 0x1000>;
clocks = <&rcc USBPHY_K>;
resets = <&rcc USBPHY_R>;
vdda1v1-supply = <&reg11>;
vdda1v8-supply = <&reg18>;
status = "disabled";
usbphyc_port0: usb-phy@0 {
#phy-cells = <0>;
reg = <0>;
};
usbphyc_port1: usb-phy@1 {
#phy-cells = <1>;
reg = <1>;
};
};
usart1: serial@5c000000 {
compatible = "st,stm32h7-uart";
reg = <0x5c000000 0x400>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc USART1_K>;
status = "disabled";
};
spi6: spi@5c001000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "st,stm32h7-spi";
reg = <0x5c001000 0x400>;
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc SPI6_K>;
resets = <&rcc SPI6_R>;
dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>,
<&mdma1 35 0x0 0x40002 0x0 0x0>;
dma-names = "rx", "tx";
status = "disabled";
};
i2c4: i2c@5c002000 {
compatible = "st,stm32f7-i2c";
reg = <0x5c002000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C4_K>;
resets = <&rcc I2C4_R>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
rtc: rtc@5c004000 {
compatible = "st,stm32mp1-rtc";
reg = <0x5c004000 0x400>;
clocks = <&rcc RTCAPB>, <&rcc RTC>;
clock-names = "pclk", "rtc_ck";
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
bsec: nvmem@5c005000 {
compatible = "st,stm32mp15-bsec";
reg = <0x5c005000 0x400>;
#address-cells = <1>;
#size-cells = <1>;
};
i2c6: i2c@5c009000 {
compatible = "st,stm32f7-i2c";
reg = <0x5c009000 0x400>;
interrupt-names = "event", "error";
interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc I2C6_K>;
resets = <&rcc I2C6_R>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
};