| /****************************************************************************** |
| * |
| * This source code has been made available to you by IBM on an AS-IS |
| * basis. Anyone receiving this source is licensed under IBM |
| * copyrights to use it in any way he or she deems fit, including |
| * copying it, modifying it, compiling it, and redistributing it either |
| * with or without modifications. No license under IBM patents or |
| * patent applications is to be implied by the copyright license. |
| * |
| * Any user of this software should understand that IBM cannot provide |
| * technical support for this software and will not be responsible for |
| * any consequences resulting from the use of this software. |
| * |
| * Any person who transfers this source code or any derivative work |
| * must include the IBM copyright notice, this paragraph, and the |
| * preceding two paragraphs in the transferred software. |
| * |
| * COPYRIGHT I B M CORPORATION 1995 |
| * LICENSED MATERIAL - PROGRAM PROPERTY OF I B M |
| * |
| *****************************************************************************/ |
| #include <config.h> |
| #include <ppc4xx.h> |
| |
| #define _LINUX_CONFIG_H 1 /* avoid reading Linux autoconf.h file */ |
| |
| #include <ppc_asm.tmpl> |
| #include <ppc_defs.h> |
| |
| #include <asm/cache.h> |
| #include <asm/mmu.h> |
| |
| #define LI32(reg,val) \ |
| addis reg,0,val@h;\ |
| ori reg,reg,val@l |
| |
| #define WDCR_EBC(reg,val) \ |
| addi r4,0,reg;\ |
| mtdcr ebccfga,r4;\ |
| addis r4,0,val@h;\ |
| ori r4,r4,val@l;\ |
| mtdcr ebccfgd,r4 |
| |
| #define WDCR_SDRAM(reg,val) \ |
| addi r4,0,reg;\ |
| mtdcr memcfga,r4;\ |
| addis r4,0,val@h;\ |
| ori r4,r4,val@l;\ |
| mtdcr memcfgd,r4 |
| |
| /****************************************************************************** |
| * Function: ext_bus_cntlr_init |
| * |
| * Description: Configures EBC Controller and a few basic chip selects. |
| * |
| * CS0 is setup to get the Boot Flash out of the addresss range |
| * so that we may setup a stack. CS7 is setup so that we can |
| * access and reset the hardware watchdog. |
| * |
| * IMPORTANT: For pass1 this code must run from |
| * cache since you can not reliably change a peripheral banks |
| * timing register (pbxap) while running code from that bank. |
| * For ex., since we are running from ROM on bank 0, we can NOT |
| * execute the code that modifies bank 0 timings from ROM, so |
| * we run it from cache. |
| * |
| * Notes: Does NOT use the stack. |
| *****************************************************************************/ |
| .section ".text" |
| .align 2 |
| .globl ext_bus_cntlr_init |
| .type ext_bus_cntlr_init, @function |
| ext_bus_cntlr_init: |
| mflr r0 |
| /******************************************************************** |
| * Prefetch entire ext_bus_cntrl_init function into the icache. |
| * This is necessary because we are going to change the same CS we |
| * are executing from. Otherwise a CPU lockup may occur. |
| *******************************************************************/ |
| bl ..getAddr |
| ..getAddr: |
| mflr r3 /* get address of ..getAddr */ |
| |
| /* Calculate number of cache lines for this function */ |
| addi r4, 0, (((.Lfe0 - ..getAddr) / CFG_CACHELINE_SIZE) + 2) |
| mtctr r4 |
| ..ebcloop: |
| icbt r0, r3 /* prefetch cache line for addr in r3*/ |
| addi r3, r3, CFG_CACHELINE_SIZE /* move to next cache line */ |
| bdnz ..ebcloop /* continue for $CTR cache lines */ |
| |
| /******************************************************************** |
| * Delay to ensure all accesses to ROM are complete before changing |
| * bank 0 timings. 200usec should be enough. |
| * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles. |
| *******************************************************************/ |
| addis r3, 0, 0x0 |
| ori r3, r3, 0xA000 /* wait 200us from reset */ |
| mtctr r3 |
| ..spinlp: |
| bdnz ..spinlp /* spin loop */ |
| |
| /******************************************************************** |
| * SETUP CPC0_CR0 |
| *******************************************************************/ |
| LI32(r4, 0x00c01030) |
| mtdcr cntrl0, r4 |
| |
| /******************************************************************** |
| * Setup CPC0_CR1: Change PCIINT signal to PerWE |
| *******************************************************************/ |
| mfdcr r4, cntrl1 |
| ori r4, r4, 0x4000 |
| mtdcr cntrl1, r4 |
| |
| /******************************************************************** |
| * Setup External Bus Controller (EBC). |
| *******************************************************************/ |
| WDCR_EBC(epcr, 0xd84c0000) |
| /******************************************************************** |
| * Memory Bank 0 (Intel 28F640J3 Flash) initialization |
| *******************************************************************/ |
| /*WDCR_EBC(pb0ap, 0x03055200)*/ |
| /*WDCR_EBC(pb0ap, 0x04055200)*/ |
| WDCR_EBC(pb0ap, 0x08055200) |
| WDCR_EBC(pb0cr, 0xff87a000) |
| /******************************************************************** |
| * Memory Bank 3 (Xilinx XC95144 CPLD) initialization |
| *******************************************************************/ |
| /*WDCR_EBC(pb3ap, 0x07869200)*/ |
| WDCR_EBC(pb3ap, 0x04055200) |
| WDCR_EBC(pb3cr, 0xf081c000) |
| /******************************************************************** |
| * Memory Bank 1,2,4-7 (Unused) initialization |
| *******************************************************************/ |
| WDCR_EBC(pb1ap, 0) |
| WDCR_EBC(pb1cr, 0) |
| WDCR_EBC(pb2ap, 0) |
| WDCR_EBC(pb2cr, 0) |
| WDCR_EBC(pb4ap, 0) |
| WDCR_EBC(pb4cr, 0) |
| WDCR_EBC(pb5ap, 0) |
| WDCR_EBC(pb5cr, 0) |
| WDCR_EBC(pb6ap, 0) |
| WDCR_EBC(pb6cr, 0) |
| WDCR_EBC(pb7ap, 0) |
| WDCR_EBC(pb7cr, 0) |
| |
| /* We are all done */ |
| mtlr r0 /* Restore link register */ |
| blr /* Return to calling function */ |
| .Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init |
| /* end ext_bus_cntlr_init() */ |
| |
| /****************************************************************************** |
| * Function: sdram_init |
| * |
| * Description: Configures SDRAM memory banks. |
| * |
| * Notes: Does NOT use the stack. |
| *****************************************************************************/ |
| .section ".text" |
| .align 2 |
| .globl sdram_init |
| .type sdram_init, @function |
| sdram_init: |
| |
| /* |
| * Disable memory controller to allow |
| * values to be changed. |
| */ |
| WDCR_SDRAM(mem_mcopt1, 0x00000000) |
| |
| /* |
| * Configure Memory Banks |
| */ |
| WDCR_SDRAM(mem_mb0cf, 0x00062001) |
| WDCR_SDRAM(mem_mb1cf, 0x00000000) |
| WDCR_SDRAM(mem_mb2cf, 0x00000000) |
| WDCR_SDRAM(mem_mb3cf, 0x00000000) |
| |
| /* |
| * Set up SDTR1 (SDRAM Timing Register) |
| */ |
| WDCR_SDRAM(mem_sdtr1, 0x00854009) |
| |
| /* |
| * Set RTR (Refresh Timing Register) |
| */ |
| WDCR_SDRAM(mem_rtr, 0x10000000) |
| /* WDCR_SDRAM(mem_rtr, 0x05f00000) */ |
| |
| /******************************************************************** |
| * Delay to ensure 200usec have elapsed since reset. Assume worst |
| * case that the core is running 200Mhz: |
| * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles |
| *******************************************************************/ |
| addis r3, 0, 0x0000 |
| ori r3, r3, 0xA000 /* Wait >200us from reset */ |
| mtctr r3 |
| ..spinlp2: |
| bdnz ..spinlp2 /* spin loop */ |
| |
| /******************************************************************** |
| * Set memory controller options reg, MCOPT1. |
| *******************************************************************/ |
| WDCR_SDRAM(mem_mcopt1,0x80800000) |
| |
| ..sdri_done: |
| blr /* Return to calling function */ |
| .Lfe1: .size sdram_init,.Lfe1-sdram_init |
| /* end sdram_init() */ |