blob: 364227197f5a95ccff82888745900d5320b74280 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
*
* Based on davinci_dvevm.h. Original Copyrights follow:
*
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* Board
*/
/* check if direct NOR boot config is used */
#ifndef CONFIG_DIRECT_NOR_BOOT
#define CONFIG_USE_SPIFLASH
#endif
/*
* SoC Configuration
*/
#define CONFIG_SYS_EXCEPTION_VECTORS_HIGH
#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
#define CONFIG_SYS_OSCIN_FREQ 24000000
#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
#define CONFIG_SKIP_LOWLEVEL_INIT_ONLY
#ifdef CONFIG_DIRECT_NOR_BOOT
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_SYS_DV_NOR_BOOT_CFG (0x11)
#endif
/*
* Memory Info
*/
#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
#define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
#define CONFIG_SPL_BSS_START_ADDR DAVINCI_DDR_EMIF_DATA_BASE
#define CONFIG_SPL_BSS_MAX_SIZE 0x1080000
/* memtest start addr */
#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000)
/* memtest will be run on 16MB */
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
DAVINCI_SYSCFG_SUSPSRC_SPI1 | \
DAVINCI_SYSCFG_SUSPSRC_UART2 | \
DAVINCI_SYSCFG_SUSPSRC_EMAC | \
DAVINCI_SYSCFG_SUSPSRC_I2C)
/*
* PLL configuration
*/
#define CONFIG_SYS_DA850_PLL0_PLLM 24
#define CONFIG_SYS_DA850_PLL1_PLLM 21
/*
* DDR2 memory configuration
*/
#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
DV_DDR_PHY_EXT_STRBEN | \
(0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDBCR ( \
(1 << DV_DDR_SDCR_MSDRAMEN_SHIFT) | \
(1 << DV_DDR_SDCR_DDREN_SHIFT) | \
(1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \
(1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \
(0x3 << DV_DDR_SDCR_CL_SHIFT) | \
(0x2 << DV_DDR_SDCR_IBANK_SHIFT) | \
(0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \
(14 << DV_DDR_SDTMR1_RFC_SHIFT) | \
(2 << DV_DDR_SDTMR1_RP_SHIFT) | \
(2 << DV_DDR_SDTMR1_RCD_SHIFT) | \
(1 << DV_DDR_SDTMR1_WR_SHIFT) | \
(5 << DV_DDR_SDTMR1_RAS_SHIFT) | \
(8 << DV_DDR_SDTMR1_RC_SHIFT) | \
(1 << DV_DDR_SDTMR1_RRD_SHIFT) | \
(0 << DV_DDR_SDTMR1_WTR_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \
(7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \
(0 << DV_DDR_SDTMR2_XP_SHIFT) | \
(0 << DV_DDR_SDTMR2_ODT_SHIFT) | \
(17 << DV_DDR_SDTMR2_XSNR_SHIFT) | \
(199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \
(0 << DV_DDR_SDTMR2_RTP_SHIFT) | \
(0 << DV_DDR_SDTMR2_CKE_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000494
#define CONFIG_SYS_DA850_DDR2_PBBPR 0x30
/*
* Serial Driver info
*/
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID)
#ifdef CONFIG_USE_SPIFLASH
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
#define CONFIG_SYS_SPI_U_BOOT_SIZE 0x40000
#endif
/*
* I2C Configuration
*/
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_I2C_EXPANDER_ADDR 0x20
#endif
/*
* Flash & Environment
*/
#ifdef CONFIG_NAND
#ifdef CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
#define CONFIG_ENV_SIZE (128 << 10)
#define CONFIG_ENV_SECT_SIZE (128 << 10)
#endif
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_PAGE_2K
#define CONFIG_SYS_NAND_CS 3
#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
#define CONFIG_SYS_NAND_MASK_CLE 0x10
#define CONFIG_SYS_NAND_MASK_ALE 0x8
#undef CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x40000
#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
CONFIG_SYS_NAND_U_BOOT_SIZE - \
CONFIG_SYS_MALLOC_LEN - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_NAND_ECCPOS { \
24, 25, 26, 27, 28, \
29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
59, 60, 61, 62, 63 }
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 10
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_NAND_LOAD
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_NAND_SELF_INIT
#endif
#endif
/*
* Network & Ethernet Configuration
*/
#ifdef CONFIG_DRIVER_TI_EMAC
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
#endif
#ifdef CONFIG_USE_NOR
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
#define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */
#define CONFIG_ENV_OFFSET (SZ_1M)
#define CONFIG_ENV_SIZE (10 << 10) /* 10KB */
#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
#define PHYS_FLASH_SIZE (8 << 20) /* Flash size 8MB */
#define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\
+ 3)
#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ
#endif
#ifdef CONFIG_USE_SPIFLASH
#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE (64 << 10)
#define CONFIG_ENV_OFFSET (512 << 10)
#define CONFIG_ENV_SECT_SIZE (64 << 10)
#endif
#ifdef CONFIG_SPL_BUILD
#undef CONFIG_SPI_FLASH_MTD
#endif
#endif
/*
* U-Boot general configuration
*/
#define CONFIG_BOOTFILE "uImage" /* Boot file name */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
/*
* Linux Information
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
#define CONFIG_HWCONFIG /* enable hwconfig */
#define CONFIG_CMDLINE_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTCOMMAND \
"run envboot; " \
"run mmcboot; "
#define DEFAULT_LINUX_BOOT_ENV \
"loadaddr=0xc0700000\0" \
"fdtaddr=0xc0600000\0" \
"scriptaddr=0xc0600000\0"
#include <environment/ti/mmc.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
DEFAULT_MMC_TI_ARGS \
"bootpart=0:2\0" \
"bootdir=/boot\0" \
"bootfile=zImage\0" \
"fdtfile=da850-evm.dtb\0" \
"boot_fdt=yes\0" \
"boot_fit=0\0" \
"console=ttyS2,115200n8\0" \
"hwconfig=dsp:wake=yes"
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#if !defined(CONFIG_NAND) && \
!defined(CONFIG_USE_NOR) && \
!defined(CONFIG_USE_SPIFLASH)
#define CONFIG_ENV_SIZE (16 << 10)
#endif
/* USB Configs */
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#ifndef CONFIG_DIRECT_NOR_BOOT
/* defines for SPL */
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
#define CONFIG_SPL_STACK 0x8001ff00
#define CONFIG_SPL_MAX_FOOTPRINT 32768
#define CONFIG_SPL_PAD_TO 32768
#endif
/* Load U-Boot Image From MMC */
/* additions for new relocation code, must added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0xc0000000
#ifdef CONFIG_DIRECT_NOR_BOOT
#define CONFIG_SYS_INIT_SP_ADDR 0x8001ff00
#else
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
GENERATED_GBL_DATA_SIZE)
#endif /* CONFIG_DIRECT_NOR_BOOT */
#include <asm/arch/hardware.h>
#endif /* __CONFIG_H */