| /* |
| * (C) Copyright 2003 Embedded Edge, LLC |
| * Dan Malek <dan@embeddededge.com> |
| * Copied from ADS85xx. |
| * Updates for Silicon Tx GP3 8560 board. |
| * |
| * (C) Copyright 2002,2003 Motorola,Inc. |
| * Xianghua Xiao <X.Xiao@motorola.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* mpc8560ads board configuration file */ |
| /* please refer to doc/README.mpc85xx for more info */ |
| /* make sure you change the MAC address and other network params first, |
| * search for CONFIG_SERVERIP, etc. in this file |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_BOOKE 1 /* BOOKE */ |
| #define CONFIG_E500 1 /* BOOKE e500 family */ |
| #define CONFIG_CPM2 1 /* has CPM2 */ |
| #define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/ |
| #define CONFIG_MPC8560 1 |
| |
| #define CONFIG_SYS_TEXT_BASE 0xfff80000 |
| |
| #undef CONFIG_PCI /* pci ethernet support */ |
| #define CONFIG_TSEC_ENET /* tsec ethernet support*/ |
| #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ |
| |
| /* sysclk for MPC85xx |
| */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33333333 /* most pci cards are 33Mhz */ |
| |
| /* Blinkin' LEDs for Robert :-) |
| */ |
| #define CONFIG_SHOW_ACTIVITY 1 |
| |
| /* |
| * These can be toggled for performance analysis, otherwise use default. |
| */ |
| #define CONFIG_L2_CACHE /* toggle L2 cache */ |
| #define CONFIG_BTB /* toggle branch predition */ |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ |
| #define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ |
| |
| #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ |
| #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ |
| #define CONFIG_SYS_MEMTEST_END 0x00400000 |
| |
| |
| /* Localbus SDRAM is an option, not all boards have it. |
| * This address, however, is used to configure a 256M local bus |
| * window that includes the Config latch below. |
| */ |
| #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ |
| #define CONFIG_SYS_LBC_SDRAM_SIZE 256 /* LBC SDRAM is 64MB */ |
| |
| #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ |
| #define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ |
| |
| #define CONFIG_SYS_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 136 /* sectors per device */ |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| /* The configuration latch is Chip Select 1. |
| * It's an 8-bit latch in the lower 8 bits of the word. |
| */ |
| #define CONFIG_SYS_BR1_PRELIM 0xfc001801 /* 32-bit port */ |
| #define CONFIG_SYS_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ |
| #define CONFIG_SYS_LBC_LCLDEVS_BASE 0xfc000000 /* Base of localbus devices */ |
| |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_SYS_RAMBOOT |
| #else |
| #undef CONFIG_SYS_RAMBOOT |
| #endif |
| |
| #ifdef CONFIG_SYS_RAMBOOT |
| #define CONFIG_SYS_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ |
| #endif |
| #define CONFIG_SYS_CCSRBAR 0xfdf00000 |
| #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR |
| |
| /* DDR Setup */ |
| #define CONFIG_SYS_FSL_DDR1 |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ |
| #define CONFIG_DDR_SPD |
| #undef CONFIG_FSL_DDR_INTERACTIVE |
| |
| #undef CONFIG_DDR_ECC /* only for ECC DDR module */ |
| #define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */ |
| #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ |
| |
| #define CONFIG_MEM_INIT_VALUE 0xDeadBeef |
| |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| |
| #define CONFIG_NUM_DDR_CONTROLLERS 1 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) |
| |
| /* I2C addresses of SPD EEPROMs */ |
| #define SPD_EEPROM_ADDRESS 0x54 /* CTLR 0 DIMM 0 */ |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| /* local bus definitions */ |
| #define CONFIG_SYS_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ |
| #define CONFIG_SYS_OR2_PRELIM 0xfc006901 |
| #define CONFIG_SYS_LBC_LCRR 0x00030004 /* local bus freq */ |
| #define CONFIG_SYS_LBC_LBCR 0x00000000 |
| #define CONFIG_SYS_LBC_LSRT 0x20000000 |
| #define CONFIG_SYS_LBC_MRTPR 0x20000000 |
| #define CONFIG_SYS_LBC_LSDMR_1 0x2861b723 |
| #define CONFIG_SYS_LBC_LSDMR_2 0x0861b723 |
| #define CONFIG_SYS_LBC_LSDMR_3 0x0861b723 |
| #define CONFIG_SYS_LBC_LSDMR_4 0x1861b723 |
| #define CONFIG_SYS_LBC_LSDMR_5 0x4061b723 |
| |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ |
| |
| /* Serial Port */ |
| #define CONFIG_CONS_ON_SCC /* define if console on SCC */ |
| #undef CONFIG_CONS_NONE /* define if console on something else */ |
| #define CONFIG_CONS_INDEX 2 /* which serial channel for console */ |
| |
| #define CONFIG_BAUDRATE 38400 |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} |
| |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| #ifdef CONFIG_SYS_HUSH_PARSER |
| #endif |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 |
| |
| #if 0 |
| #define CONFIG_SYS_I2C_NOPROBES {0x00} /* Don't probe these addrs */ |
| #else |
| /* I did the 'if 0' so we could keep the syntax above if ever needed. */ |
| #undef CONFIG_SYS_I2C_NOPROBES |
| #endif |
| |
| /* RapdIO Map configuration, mapped 1:1. |
| */ |
| #define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 |
| #define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE |
| #define CONFIG_SYS_RIO_MEM_SIZE 0x200000000 /* 512 M */ |
| |
| /* Standard 8560 PCI addressing, mapped 1:1. |
| */ |
| #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 |
| #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE |
| #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCI1_IO_BASE 0xe2000000 |
| #define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE |
| #define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16 M */ |
| |
| #if defined(CONFIG_PCI) /* PCI Ethernet card */ |
| |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_TULIP |
| |
| #if !defined(CONFIG_PCI_PNP) |
| #define PCI_ENET0_IOADDR 0xe0000000 |
| #define PCI_ENET0_MEMADDR 0xe0000000 |
| #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ |
| #endif |
| |
| #undef CONFIG_PCI_SCAN_SHOW |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ |
| |
| #endif /* CONFIG_PCI */ |
| |
| #if defined(CONFIG_TSEC_ENET) |
| |
| #define CONFIG_MII 1 /* MII PHY management */ |
| |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "TSEC0" |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "TSEC1" |
| |
| #define TSEC1_PHY_ADDR 2 |
| #define TSEC2_PHY_ADDR 4 |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC1_FLAGS TSEC_GIGABIT |
| #define TSEC2_FLAGS TSEC_GIGABIT |
| #define CONFIG_ETHPRIME "TSEC0" |
| |
| #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ |
| |
| #define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */ |
| #undef CONFIG_ETHER_NONE /* define if ether on something else */ |
| #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ |
| |
| #if (CONFIG_ETHER_INDEX == 2) |
| /* |
| * - Rx-CLK is CLK13 |
| * - Tx-CLK is CLK14 |
| * - Select bus for bd/buffers |
| * - Full duplex |
| */ |
| #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) |
| #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) |
| #define CONFIG_SYS_CPMFCR_RAMTYPE 0 |
| #if 0 |
| #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE) |
| #else |
| #define CONFIG_SYS_FCC_PSMR 0 |
| #endif |
| #define FETH2_RST 0x01 |
| #elif (CONFIG_ETHER_INDEX == 3) |
| /* need more definitions here for FE3 */ |
| #define FETH3_RST 0x80 |
| #endif /* CONFIG_ETHER_INDEX */ |
| |
| /* MDIO is done through the TSEC0 control. |
| */ |
| #define CONFIG_MII /* MII PHY management */ |
| #undef CONFIG_BITBANGMII /* bit-bang MII PHY management */ |
| |
| #endif |
| |
| /* Environment */ |
| /* We use the top boot sector flash, so we have some 16K sectors for env |
| */ |
| #ifndef CONFIG_SYS_RAMBOOT |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000) |
| #define CONFIG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */ |
| #define CONFIG_ENV_SIZE 0x2000 |
| #else |
| #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ |
| #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif |
| |
| #define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400" |
| #define CONFIG_BOOTCOMMAND "bootm 0xff000000 0xff100000" |
| #define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_REGINFO |
| |
| #if !defined(CONFIG_SYS_RAMBOOT) |
| #define CONFIG_CMD_ELF |
| #endif |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) |
| #define CONFIG_CMD_MII |
| #endif |
| |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #endif |
| |
| #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_HAS_ETH2 |
| #endif |
| |
| #define CONFIG_SERVERIP 192.168.85.1 |
| #define CONFIG_IPADDR 192.168.85.60 |
| #define CONFIG_GATEWAYIP 192.168.85.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_HOSTNAME STX_GP3 |
| #define CONFIG_ROOTPATH "/gppproot" |
| #define CONFIG_BOOTFILE "uImage" |
| #define CONFIG_LOADADDR 0x1000000 |
| |
| #endif /* __CONFIG_H */ |