include/configs/P1023RDS.h - github/trini/u-boot - Gitiles

 /*
  * Copyright 2010-2012 Freescale Semiconductor, Inc.
  *
  * Authors:  Roy Zang <tie-fei.zang@freescale.com>
  *	     Chunhe Lan <b25806@freescale.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /*
  * p1023rds board configuration file
  *
  */
 #ifndef __CONFIG_H
 #define __CONFIG_H

 #ifdef CONFIG_NAND
 #define CONFIG_NAND_U_BOOT
 #define CONFIG_RAMBOOT_NAND
 #endif

 #ifdef CONFIG_NAND_U_BOOT
 #define CONFIG_SYS_TEXT_BASE_SPL	0xfff00000
 #define CONFIG_SYS_TEXT_BASE		0x11001000

 #ifdef CONFIG_NAND_SPL
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
 #else
 #define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 #endif /* CONFIG_NAND_SPL */
 #endif

 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xeff40000
 #endif

 #ifndef CONFIG_SYS_MONITOR_BASE
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 #endif

 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
 #endif

 /* High Level Configuration Options */
 #define CONFIG_BOOKE		/* BOOKE */
 #define CONFIG_E500		/* BOOKE e500 family */
 #define CONFIG_P1023
 #define CONFIG_P1023RDS
 #define CONFIG_MP		/* support multiple processors */

 #define CONFIG_FSL_ELBC		/* Has Enhanced localbus controller */
 #define CONFIG_PCI		/* Enable PCI/PCIE */
 #define CONFIG_PCIE1		/* PCIE controler 1 (slot 1) */
 #define CONFIG_PCIE2		/* PCIE controler 2 (slot 2) */
 #define CONFIG_PCIE3		/* PCIE controler 3 (slot 3) */
 #define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
 #define CONFIG_FSL_PCIE_RESET	/* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
 #define CONFIG_FSL_LAW		/* Use common FSL init code */

 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif

 #define CONFIG_SYS_CLK_FREQ	66666666
 #define CONFIG_DDR_CLK_FREQ	CONFIG_SYS_CLK_FREQ

 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_L2_CACHE			/* toggle L2 cache */
 #define CONFIG_BTB			/* toggle branch predition */
 #define CONFIG_HWCONFIG

 #define CONFIG_ENABLE_36BIT_PHYS

 #define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x1fffffff	/* fix me, only 1G */
 #define CONFIG_PANIC_HANG	/* do not reset board on panic */

 #define CONFIG_SYS_LBC_LBCR	0x00000000	/* Implement conversion of
 						addresses in the LBC */

 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM

 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef

 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	2

 /* These are used when DDR doesn't use SPD.  */
 #define CONFIG_SYS_SDRAM_SIZE		2048u	/* DDR is 2GB */

 /* Default settings for "stable" mode */
 #define CONFIG_SYS_DDR_CS0_BNDS		0x0000003F
 #define CONFIG_SYS_DDR_CS1_BNDS		0x0040007F
 #define CONFIG_SYS_DDR_CS0_CONFIG	0x80014302
 #define CONFIG_SYS_DDR_CS1_CONFIG	0x80014302
 #define CONFIG_SYS_DDR_TIMING_3		0x00020000
 #define CONFIG_SYS_DDR_TIMING_0		0x40110104
 #define CONFIG_SYS_DDR_TIMING_1		0x5C59E544
 #define CONFIG_SYS_DDR_TIMING_2		0x0fA888CA
 #define CONFIG_SYS_DDR_MODE_1		0x00441210
 #define CONFIG_SYS_DDR_MODE_2		0x00000000
 #define CONFIG_SYS_DDR_MODE_CTRL	0x00000000
 #define CONFIG_SYS_DDR_INTERVAL		0x0A280100
 #define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
 #define CONFIG_SYS_DDR_CLK_CTRL		0x01800000
 #define CONFIG_SYS_DDR_TIMING_4		0x00000001
 #define CONFIG_SYS_DDR_TIMING_5		0x01401400
 #define CONFIG_SYS_DDR_ZQ_CNTL		0x89080600
 #define CONFIG_SYS_DDR_WRLVL_CNTL	0x8675F605
 #define CONFIG_SYS_DDR_CONTROL	0xC70C0008 /* Type = DDR3: No Interleaving */
 #define CONFIG_SYS_DDR_CONTROL2		0x24401010
 #define CONFIG_SYS_DDR_CDR1		0x00000000
 #define CONFIG_SYS_DDR_CDR2		0x00000000

 #define CONFIG_SYS_DDR_ERR_INT_EN	0x00000000
 #define CONFIG_SYS_DDR_ERR_DIS		0x00000000
 #define CONFIG_SYS_DDR_SBE		0x00000000

 /* Settings that differ for "performance" mode */
 #define CONFIG_SYS_DDR_CS0_BNDS_PERF	0x0000007F /* Interleaving Enabled */
 #define CONFIG_SYS_DDR_CS1_BNDS_PERF	0x00000000 /* Interleaving Enabled */
 #define CONFIG_SYS_DDR_CS1_CONFIG_PERF	0x80014302
 #define CONFIG_SYS_DDR_TIMING_1_PERF	0x5C58E544
 #define CONFIG_SYS_DDR_TIMING_2_PERF	0x0FA888CA
 /* Type = DDR3: cs0-cs1 interleaving */
 #define CONFIG_SYS_DDR_CONTROL_PERF	0xC70C4008
 #define CONFIG_SYS_DDR_CDR_1		0x00000000
 #define CONFIG_SYS_DDR_CDR_2		0x00000000


 /*
  * Memory map
  *
  * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
  * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
  * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
  * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
  *
  * Localbus non-cacheable
  * 0xe000_0000	0xe003_ffff	BCSR			256K BCSR
  * 0xee00_0000	0xefff_ffff	NOR flash		32M NOR flash
  * 0xff00_0000	0xff3f_ffff	DPAA_QBMAN		4M
  * 0xff60_0000	0xff7f_ffff	CCSR			2M non-cacheable
  * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
  * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
  */

 /*
  * Local Bus Definitions
  */
 #define CONFIG_SYS_BCSR_BASE		0xe0000000 /* start of on board FPGA */
 #define CONFIG_SYS_BCSR_BASE_PHYS	CONFIG_SYS_BCSR_BASE

 #ifndef CONFIG_NAND
 #define CONFIG_SYS_FLASH_BASE		0xee000000 /* start of FLASH 32M */

 #define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE

 #define CONFIG_FLASH_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 		| BR_PS_16 | BR_V)
 #define CONFIG_FLASH_OR_PRELIM	0xfe000ff7

 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
 #else
 #define CONFIG_SYS_NO_FLASH
 #endif

 #if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND)
 #define CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_BOARD_EARLY_INIT_F	/* call board_early_init_f function */
 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */

 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_END	0x00004000	/* End of used area in RAM */

 #define CONFIG_SYS_GBL_DATA_OFFSET	\
 	(CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN	(768 * 1024)
 #define CONFIG_SYS_MALLOC_LEN	(6 * 1024 * 1024) /* Reserved for malloc */

 #ifndef CONFIG_NAND_SPL
 #define CONFIG_SYS_NAND_BASE		0xffa00000
 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
 #else
 #define CONFIG_SYS_NAND_BASE		0xfff00000
 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
 #endif

 #define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE}
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_MTD_NAND_VERIFY_WRITE
 #define CONFIG_CMD_NAND
 #define CONFIG_NAND_FSL_ELBC
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(16 * 1024)

 /* NAND boot: 4K NAND loader config */
 #define CONFIG_SYS_NAND_SPL_SIZE	0x1000
 #define CONFIG_SYS_NAND_U_BOOT_SIZE	((768 << 10) + CONFIG_SYS_NAND_SPL_SIZE)
 #define CONFIG_SYS_NAND_U_BOOT_DST	(0x11000000 - CONFIG_SYS_NAND_SPL_SIZE)
 #define CONFIG_SYS_NAND_U_BOOT_START	0x11000000
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	(0)
 #define CONFIG_SYS_NAND_U_BOOT_RELOC	0x00010000
 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP	(CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)

 /* NAND flash config */
 #define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
 				| BR_PS_8		/* Port Size = 8bit */ \
 				| BR_MS_FCM		/* MSEL = FCM */ \
 				| BR_V)			/* valid */
 #define CONFIG_SYS_NAND_OR_PRELIM  (0xFFF80000		/* length 32K */ \
 				| OR_FCM_CSCT \
 				| OR_FCM_CST \
 				| OR_FCM_CHT \
 				| OR_FCM_SCY_1 \
 				| OR_FCM_TRLX \
 				| OR_FCM_EHTR)

 #ifdef CONFIG_RAMBOOT_NAND
 /* NAND Base Address */
 #define CONFIG_SYS_BR0_PRELIM	CONFIG_SYS_NAND_BR_PRELIM
 #define CONFIG_SYS_OR0_PRELIM	CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 /* chip select 1 - BCSR */
 #define CONFIG_SYS_BR1_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
 				| BR_MS_GPCM | BR_PS_8 | BR_V)
 #define CONFIG_SYS_OR1_PRELIM  (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
 				| OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
 				| OR_GPCM_EAD)
 #else
 #define CONFIG_SYS_BR0_PRELIM  CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
 #define CONFIG_SYS_OR0_PRELIM  CONFIG_FLASH_OR_PRELIM	/* NOR Options */
 /* chip select 1 - BCSR */
 #define CONFIG_SYS_BR1_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
 				| BR_MS_GPCM | BR_PS_8 | BR_V)
 #define CONFIG_SYS_OR1_PRELIM  (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
 				| OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
 				| OR_GPCM_EAD)
 #endif

 /* Serial Port
  * open - index 2
  * shorted - index 1
  */
 #define CONFIG_CONS_INDEX		1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
 #ifdef CONFIG_NAND_SPL
 #define CONFIG_NS16550_MIN_FUNCTIONS
 #endif

 #define CONFIG_SYS_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR + 0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR + 0x4600)

 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER

 /*
  * Pass open firmware flat tree
  */
 #define CONFIG_OF_LIBFDT
 #define CONFIG_OF_BOARD_SETUP
 #define CONFIG_OF_STDOUT_VIA_ALIAS

 /* new uImage format support */
 #define CONFIG_FIT
 #define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x51

 /*
  * I2C2 EEPROM
  */
 #define CONFIG_ID_EEPROM
 #ifdef CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #endif
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x51
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 #define CONFIG_SYS_EEPROM_BUS_NUM	0

 #define CONFIG_CMD_I2C

 /*
  * eSPI - Enhanced SPI
  */
 #define CONFIG_SPI_FLASH
 #define CONFIG_SPI_FLASH_ATMEL

 #define CONFIG_HARD_SPI
 #define CONFIG_FSL_ESPI

 #define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED		10000000
 #define CONFIG_SF_DEFAULT_MODE		0

 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */

 /* controller 3, Slot 1, tgtid 3, Base address b000 */
 #define CONFIG_SYS_PCIE3_NAME		"Slot 3"
 #define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
 #define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
 #define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
 #define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
 #define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
 #define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */

 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 #define CONFIG_SYS_PCIE2_NAME		"Slot 2"
 #define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */

 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 #define CONFIG_SYS_PCIE1_NAME		"Slot 1"
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */

 #if defined(CONFIG_PCI)
 #define CONFIG_E1000		/* Defind e1000 pci Ethernet card */
 #define CONFIG_PCI_PNP		/* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
 #endif	/* CONFIG_PCI */

 /*
  * Environment
  */
 #define CONFIG_ENV_OVERWRITE

 #if defined(CONFIG_SYS_RAMBOOT)
 #if defined(CONFIG_RAMBOOT_NAND)
 #define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
 #define CONFIG_ENV_OFFSET	((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
 #else
 #define CONFIG_ENV_IS_NOWHERE	/* Store ENV in memory only */
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x4000)
 #define CONFIG_ENV_SIZE		0x2000
 #endif
 #else
 #define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
 #endif

 #define CONFIG_LOADS_ECHO		/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_SETEXPR
 #define CONFIG_CMD_REGINFO

 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_NET
 #endif

 /*
  * USB
  */
 #define CONFIG_HAS_FSL_DR_USB
 #ifdef CONFIG_HAS_FSL_DR_USB
 #define CONFIG_USB_EHCI

 #ifdef CONFIG_USB_EHCI
 #define CONFIG_CMD_USB
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_USB_STORAGE
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 #endif
 #endif

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_CMDLINE_EDITING		/* Command-line editing */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
 #endif
 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 16 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(16 << 20) /* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(16 << 20) /* Increase max gunzip size */

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_BOOTFILE		"uImage"
 #define CONFIG_UBOOTPATH	(u-boot.bin) /* U-Boot image on TFTP server */

 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR		1000000

 #define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */

 #define CONFIG_BAUDRATE	115200

 /* Qman/Bman */
 #define CONFIG_SYS_DPAA_QBMAN		/* support Q/Bman */
 #define CONFIG_SYS_QMAN_MEM_BASE	0xff000000
 #define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
 #define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
 #define CONFIG_SYS_BMAN_MEM_BASE	0xff200000
 #define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
 #define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000

 /* For FM */
 #define CONFIG_SYS_DPAA_FMAN
 #define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */

 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
 #define CONFIG_PHY_MARVELL
 #endif

 #ifndef CONFIG_NAND
 /* Default address of microcode for the Linux Fman driver */
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 #define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #else
 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 #define CONFIG_SYS_FMAN_FW_ADDR	0x1f00000
 #endif
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

 #ifdef CONFIG_FMAN_ENET
 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x2
 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR	0x7

 #define CONFIG_SYS_TBIPA_VALUE	8
 #define CONFIG_MII		/* MII PHY management */
 #define CONFIG_ETHPRIME		"FM1@DTSEC1"
 #endif

 #define CONFIG_EXTRA_ENV_SETTINGS	\
 	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"

 #endif	/* __CONFIG_H */
	/*
	* Copyright 2010-2012 Freescale Semiconductor, Inc.
	*
	* Authors: Roy Zang <tie-fei.zang@freescale.com>
	* Chunhe Lan <b25806@freescale.com>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/*
	* p1023rds board configuration file
	*
	*/
	#ifndef __CONFIG_H
	#define __CONFIG_H

	#ifdef CONFIG_NAND
	#define CONFIG_NAND_U_BOOT
	#define CONFIG_RAMBOOT_NAND
	#endif

	#ifdef CONFIG_NAND_U_BOOT
	#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
	#define CONFIG_SYS_TEXT_BASE 0x11001000

	#ifdef CONFIG_NAND_SPL
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
	#else
	#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#endif /* CONFIG_NAND_SPL */
	#endif

	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0xeff40000
	#endif

	#ifndef CONFIG_SYS_MONITOR_BASE
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#endif

	#ifndef CONFIG_RESET_VECTOR_ADDRESS
	#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
	#endif

	/* High Level Configuration Options */
	#define CONFIG_BOOKE /* BOOKE */
	#define CONFIG_E500 /* BOOKE e500 family */
	#define CONFIG_P1023
	#define CONFIG_P1023RDS
	#define CONFIG_MP /* support multiple processors */

	#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
	#define CONFIG_PCI /* Enable PCI/PCIE */
	#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
	#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
	#define CONFIG_PCIE3 /* PCIE controler 3 (slot 3) */
	#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
	#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
	#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
	#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
	#define CONFIG_FSL_LAW /* Use common FSL init code */

	#ifndef __ASSEMBLY__
	extern unsigned long get_clock_freq(void);
	#endif

	#define CONFIG_SYS_CLK_FREQ 66666666
	#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ

	/*
	* These can be toggled for performance analysis, otherwise use default.
	*/
	#define CONFIG_L2_CACHE /* toggle L2 cache */
	#define CONFIG_BTB /* toggle branch predition */
	#define CONFIG_HWCONFIG

	#define CONFIG_ENABLE_36BIT_PHYS

	#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x1fffffff /* fix me, only 1G */
	#define CONFIG_PANIC_HANG /* do not reset board on panic */

	#define CONFIG_SYS_LBC_LBCR 0x00000000 /* Implement conversion of
	addresses in the LBC */

	/* DDR Setup */
	#define CONFIG_VERY_BIG_RAM

	#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
	#define CONFIG_MEM_INIT_VALUE 0xDeadBeef

	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE

	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	#define CONFIG_CHIP_SELECTS_PER_CTRL 2

	/* These are used when DDR doesn't use SPD. */
	#define CONFIG_SYS_SDRAM_SIZE 2048u /* DDR is 2GB */

	/* Default settings for "stable" mode */
	#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
	#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007F
	#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
	#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
	#define CONFIG_SYS_DDR_TIMING_3 0x00020000
	#define CONFIG_SYS_DDR_TIMING_0 0x40110104
	#define CONFIG_SYS_DDR_TIMING_1 0x5C59E544
	#define CONFIG_SYS_DDR_TIMING_2 0x0fA888CA
	#define CONFIG_SYS_DDR_MODE_1 0x00441210
	#define CONFIG_SYS_DDR_MODE_2 0x00000000
	#define CONFIG_SYS_DDR_MODE_CTRL 0x00000000
	#define CONFIG_SYS_DDR_INTERVAL 0x0A280100
	#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
	#define CONFIG_SYS_DDR_CLK_CTRL 0x01800000
	#define CONFIG_SYS_DDR_TIMING_4 0x00000001
	#define CONFIG_SYS_DDR_TIMING_5 0x01401400
	#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600
	#define CONFIG_SYS_DDR_WRLVL_CNTL 0x8675F605
	#define CONFIG_SYS_DDR_CONTROL 0xC70C0008 /* Type = DDR3: No Interleaving */
	#define CONFIG_SYS_DDR_CONTROL2 0x24401010
	#define CONFIG_SYS_DDR_CDR1 0x00000000
	#define CONFIG_SYS_DDR_CDR2 0x00000000

	#define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000
	#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
	#define CONFIG_SYS_DDR_SBE 0x00000000

	/* Settings that differ for "performance" mode */
	#define CONFIG_SYS_DDR_CS0_BNDS_PERF 0x0000007F /* Interleaving Enabled */
	#define CONFIG_SYS_DDR_CS1_BNDS_PERF 0x00000000 /* Interleaving Enabled */
	#define CONFIG_SYS_DDR_CS1_CONFIG_PERF 0x80014302
	#define CONFIG_SYS_DDR_TIMING_1_PERF 0x5C58E544
	#define CONFIG_SYS_DDR_TIMING_2_PERF 0x0FA888CA
	/* Type = DDR3: cs0-cs1 interleaving */
	#define CONFIG_SYS_DDR_CONTROL_PERF 0xC70C4008
	#define CONFIG_SYS_DDR_CDR_1 0x00000000
	#define CONFIG_SYS_DDR_CDR_2 0x00000000


	/*
	* Memory map
	*
	* 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
	* 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
	* 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
	* 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
	*
	* Localbus non-cacheable
	* 0xe000_0000 0xe003_ffff BCSR 256K BCSR
	* 0xee00_0000 0xefff_ffff NOR flash 32M NOR flash
	* 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M
	* 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
	* 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
	* 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
	*/

	/*
	* Local Bus Definitions
	*/
	#define CONFIG_SYS_BCSR_BASE 0xe0000000 /* start of on board FPGA */
	#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE

	#ifndef CONFIG_NAND
	#define CONFIG_SYS_FLASH_BASE 0xee000000 /* start of FLASH 32M */

	#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE

	#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
	\| BR_PS_16 \| BR_V)
	#define CONFIG_FLASH_OR_PRELIM 0xfe000ff7

	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_SYS_FLASH_EMPTY_INFO

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
	#else
	#define CONFIG_SYS_NO_FLASH
	#endif

	#if defined(CONFIG_SYS_SPL) \|\| defined(CONFIG_RAMBOOT_NAND)
	#define CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */
	#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */

	#define CONFIG_SYS_INIT_RAM_LOCK
	#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
	#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */

	#define CONFIG_SYS_GBL_DATA_OFFSET \
	(CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
	#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */

	#ifndef CONFIG_NAND_SPL
	#define CONFIG_SYS_NAND_BASE 0xffa00000
	#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
	#else
	#define CONFIG_SYS_NAND_BASE 0xfff00000
	#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
	#endif

	#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_MTD_NAND_VERIFY_WRITE
	#define CONFIG_CMD_NAND
	#define CONFIG_NAND_FSL_ELBC
	#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)

	/* NAND boot: 4K NAND loader config */
	#define CONFIG_SYS_NAND_SPL_SIZE 0x1000
	#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) + CONFIG_SYS_NAND_SPL_SIZE)
	#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000 - CONFIG_SYS_NAND_SPL_SIZE)
	#define CONFIG_SYS_NAND_U_BOOT_START 0x11000000
	#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
	#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
	#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)

	/* NAND flash config */
	#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	\| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
	\| BR_PS_8 /* Port Size = 8bit */ \
	\| BR_MS_FCM /* MSEL = FCM */ \
	\| BR_V) /* valid */
	#define CONFIG_SYS_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \
	\| OR_FCM_CSCT \
	\| OR_FCM_CST \
	\| OR_FCM_CHT \
	\| OR_FCM_SCY_1 \
	\| OR_FCM_TRLX \
	\| OR_FCM_EHTR)

	#ifdef CONFIG_RAMBOOT_NAND
	/* NAND Base Address */
	#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
	#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
	/* chip select 1 - BCSR */
	#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
	\| BR_MS_GPCM \| BR_PS_8 \| BR_V)
	#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \| OR_GPCM_CSNT \| OR_GPCM_XACS \
	\| OR_GPCM_SCY \| OR_GPCM_TRLX \| OR_GPCM_EHTR \
	\| OR_GPCM_EAD)
	#else
	#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
	#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
	/* chip select 1 - BCSR */
	#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
	\| BR_MS_GPCM \| BR_PS_8 \| BR_V)
	#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \| OR_GPCM_CSNT \| OR_GPCM_XACS \
	\| OR_GPCM_SCY \| OR_GPCM_TRLX \| OR_GPCM_EHTR \
	\| OR_GPCM_EAD)
	#endif

	/* Serial Port
	* open - index 2
	* shorted - index 1
	*/
	#define CONFIG_CONS_INDEX 1
	#undef CONFIG_SERIAL_SOFTWARE_FIFO
	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
	#ifdef CONFIG_NAND_SPL
	#define CONFIG_NS16550_MIN_FUNCTIONS
	#endif

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)

	/* Use the HUSH parser */
	#define CONFIG_SYS_HUSH_PARSER

	/*
	* Pass open firmware flat tree
	*/
	#define CONFIG_OF_LIBFDT
	#define CONFIG_OF_BOARD_SETUP
	#define CONFIG_OF_STDOUT_VIA_ALIAS

	/* new uImage format support */
	#define CONFIG_FIT
	#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51

	/*
	* I2C2 EEPROM
	*/
	#define CONFIG_ID_EEPROM
	#ifdef CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#endif
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_BUS_NUM 0

	#define CONFIG_CMD_I2C

	/*
	* eSPI - Enhanced SPI
	*/
	#define CONFIG_SPI_FLASH
	#define CONFIG_SPI_FLASH_ATMEL

	#define CONFIG_HARD_SPI
	#define CONFIG_FSL_ESPI

	#define CONFIG_CMD_SF
	#define CONFIG_SF_DEFAULT_SPEED 10000000
	#define CONFIG_SF_DEFAULT_MODE 0

	/*
	* General PCI
	* Memory space is mapped 1-1, but I/O space must start from 0.
	*/

	/* controller 3, Slot 1, tgtid 3, Base address b000 */
	#define CONFIG_SYS_PCIE3_NAME "Slot 3"
	#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
	#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
	#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
	#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
	#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
	#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
	#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */

	/* controller 2, direct to uli, tgtid 2, Base address 9000 */
	#define CONFIG_SYS_PCIE2_NAME "Slot 2"
	#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
	#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
	#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
	#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
	#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
	#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
	#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */

	/* controller 1, Slot 2, tgtid 1, Base address a000 */
	#define CONFIG_SYS_PCIE1_NAME "Slot 1"
	#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
	#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
	#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */

	#if defined(CONFIG_PCI)
	#define CONFIG_E1000 /* Defind e1000 pci Ethernet card */
	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#endif /* CONFIG_PCI */

	/*
	* Environment
	*/
	#define CONFIG_ENV_OVERWRITE

	#if defined(CONFIG_SYS_RAMBOOT)
	#if defined(CONFIG_RAMBOOT_NAND)
	#define CONFIG_ENV_IS_IN_NAND
	#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
	#define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
	#else
	#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x4000)
	#define CONFIG_ENV_SIZE 0x2000
	#endif
	#else
	#define CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE 0x2000
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
	#endif

	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */

	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_IRQ
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_ELF
	#define CONFIG_CMD_SETEXPR
	#define CONFIG_CMD_REGINFO

	#if defined(CONFIG_PCI)
	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_NET
	#endif

	/*
	* USB
	*/
	#define CONFIG_HAS_FSL_DR_USB
	#ifdef CONFIG_HAS_FSL_DR_USB
	#define CONFIG_USB_EHCI

	#ifdef CONFIG_USB_EHCI
	#define CONFIG_CMD_USB
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	#define CONFIG_USB_EHCI_FSL
	#define CONFIG_USB_STORAGE
	#define CONFIG_CMD_FAT
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_FAT
	#define CONFIG_DOS_PARTITION
	#endif
	#endif

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_CMDLINE_EDITING /* Command-line editing */
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 16 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_BOOTFILE "uImage"
	#define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */

	/* default location for tftp and bootm */
	#define CONFIG_LOADADDR 1000000

	#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */

	#define CONFIG_BAUDRATE 115200

	/* Qman/Bman */
	#define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */
	#define CONFIG_SYS_QMAN_MEM_BASE 0xff000000
	#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
	#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
	#define CONFIG_SYS_BMAN_MEM_BASE 0xff200000
	#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
	#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000

	/* For FM */
	#define CONFIG_SYS_DPAA_FMAN
	#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */

	#ifdef CONFIG_SYS_DPAA_FMAN
	#define CONFIG_FMAN_ENET
	#define CONFIG_PHY_MARVELL
	#endif

	#ifndef CONFIG_NAND
	/* Default address of microcode for the Linux Fman driver */
	/* QE microcode/firmware address */
	#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
	#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
	#else
	#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
	#define CONFIG_SYS_FMAN_FW_ADDR 0x1f00000
	#endif
	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

	#ifdef CONFIG_FMAN_ENET
	#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2
	#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x7

	#define CONFIG_SYS_TBIPA_VALUE 8
	#define CONFIG_MII /* MII PHY management */
	#define CONFIG_ETHPRIME "FM1@DTSEC1"
	#endif

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"

	#endif /* __CONFIG_H */