blob: 1b566c01eeb7cbfc0f7f7e21cc74ca01f89e0ef5 [file] [log] [blame]
/*
* (C) Copyright 2006-2008
* Texas Instruments.
* Richard Woodruff <r-woodruff2@ti.com>
* Syed Mohammed Khasim <x0khasim@ti.com>
*
* Configuration settings for the TI OMAP3530 Beagle board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
#define CONFIG_OMAP3_BEAGLE 1 /* working with BEAGLE */
#define CONFIG_OMAP_GPIO
#define CONFIG_OMAP_COMMON
#define CONFIG_SDRC /* The chip has SDRC controller */
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap3.h>
/*
* Display CPU and Board information
*/
#define CONFIG_DISPLAY_CPUINFO 1
#define CONFIG_DISPLAY_BOARDINFO 1
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
#define CONFIG_MISC_INIT_R
#define CONFIG_OF_LIBFDT
#define CONFIG_CMD_BOOTZ
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
#define CONFIG_REVISION_TAG 1
/*
* Size of malloc() pool
*/
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
/*
* Hardware drivers
*/
/*
* NS16550 Configuration
*/
#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
/*
* select serial console configuration
*/
#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
#define CONFIG_SERIAL3 3 /* UART3 on Beagle Rev 2 */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
#define CONFIG_GENERIC_MMC 1
#define CONFIG_MMC 1
#define CONFIG_OMAP_HSMMC 1
#define CONFIG_DOS_PARTITION 1
/* Status LED */
#define CONFIG_STATUS_LED 1
#define CONFIG_BOARD_SPECIFIC_LED 1
#define STATUS_LED_BIT 0x01
#define STATUS_LED_STATE STATUS_LED_ON
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
#define STATUS_LED_BIT1 0x02
#define STATUS_LED_STATE1 STATUS_LED_ON
#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
#define STATUS_LED_BOOT STATUS_LED_BIT
#define STATUS_LED_GREEN STATUS_LED_BIT1
/* Enable Multi Bus support for I2C */
#define CONFIG_I2C_MULTI_BUS 1
/* Probe all devices */
#define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}}
/* USB */
#define CONFIG_MUSB_GADGET
#define CONFIG_USB_MUSB_OMAP2PLUS
#define CONFIG_MUSB_PIO_ONLY
#define CONFIG_USB_GADGET_DUALSPEED
#define CONFIG_TWL4030_USB 1
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETHER_RNDIS
/* USB EHCI */
#define CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_USB_ETHER_ASIX
/* GPIO banks */
#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
/* commands to include */
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_EXT2 /* EXT2 Support */
#define CONFIG_CMD_FAT /* FAT support */
#define CONFIG_CMD_FS_GENERIC /* Generic FS support */
#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define MTDIDS_DEFAULT "nand0=nand"
#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
"1920k(u-boot),128k(u-boot-env),"\
"4m(kernel),-(fs)"
#define CONFIG_CMD_I2C /* I2C serial bus support */
#define CONFIG_CMD_MMC /* MMC support */
#define CONFIG_USB_STORAGE /* USB storage support */
#define CONFIG_CMD_NAND /* NAND support */
#define CONFIG_CMD_LED /* LED support */
#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
#define CONFIG_CMD_NFS /* NFS support */
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SETEXPR /* Evaluate expressions */
#define CONFIG_CMD_GPIO /* Enable gpio command */
#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
#undef CONFIG_CMD_IMI /* iminfo */
#undef CONFIG_CMD_IMLS /* List all found images */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_I2C
#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
#define CONFIG_SYS_I2C_OMAP34XX
#define CONFIG_VIDEO_OMAP3 /* DSS Support */
/*
* TWL4030
*/
#define CONFIG_TWL4030_POWER 1
#define CONFIG_TWL4030_LED 1
/*
* Board NAND Info.
*/
#define CONFIG_SYS_NAND_QUIET_TEST 1
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
/* Environment information */
#define CONFIG_BOOTDELAY 3
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x80200000\0" \
"rdaddr=0x81000000\0" \
"fdt_high=0xffffffff\0" \
"fdtaddr=0x80f80000\0" \
"usbtty=cdc_acm\0" \
"bootfile=uImage\0" \
"ramdisk=ramdisk.gz\0" \
"bootdir=/boot\0" \
"bootpart=0:2\0" \
"console=ttyO2,115200n8\0" \
"mpurate=auto\0" \
"buddy=none\0" \
"optargs=\0" \
"camera=none\0" \
"vram=12M\0" \
"dvimode=640x480MR-16@60\0" \
"defaultdisplay=dvi\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext3 rootwait\0" \
"nandroot=ubi0:rootfs ubi.mtd=4\0" \
"nandrootfstype=ubifs\0" \
"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
"ramrootfstype=ext2\0" \
"mmcargs=setenv bootargs console=${console} " \
"${optargs} " \
"mpurate=${mpurate} " \
"buddy=${buddy} "\
"camera=${camera} "\
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"nandargs=setenv bootargs console=${console} " \
"${optargs} " \
"mpurate=${mpurate} " \
"buddy=${buddy} "\
"camera=${camera} "\
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
"findfdt=" \
"if test $beaglerev = AxBx; then " \
"setenv fdtfile omap3-beagle.dtb; fi; " \
"if test $beaglerev = Cx; then " \
"setenv fdtfile omap3-beagle.dtb; fi; " \
"if test $beaglerev = xMAB; then " \
"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
"if test $beaglerev = xMC; then " \
"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
"if test $fdtfile = undefined; then " \
"echo WARNING: Could not determine device tree to use; fi; \0" \
"bootenv=uEnv.txt\0" \
"loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
"importbootenv=echo Importing environment from mmc ...; " \
"env import -t $loadaddr $filesize\0" \
"ramargs=setenv bootargs console=${console} " \
"${optargs} " \
"mpurate=${mpurate} " \
"buddy=${buddy} "\
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${ramroot} " \
"rootfstype=${ramrootfstype}\0" \
"loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
"mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
"run mmcargs; " \
"bootz ${loadaddr} - ${fdtaddr}\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
"nand read ${loadaddr} 280000 400000; " \
"bootm ${loadaddr}\0" \
"ramboot=echo Booting from ramdisk ...; " \
"run ramargs; " \
"bootm ${loadaddr}\0" \
"userbutton=if gpio input 173; then run userbutton_xm; " \
"else run userbutton_nonxm; fi;\0" \
"userbutton_xm=gpio input 4;\0" \
"userbutton_nonxm=gpio input 7;\0"
/* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
#define CONFIG_BOOTCOMMAND \
"run findfdt; " \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run userbutton; then " \
"setenv bootenv uEnv.txt;" \
"else " \
"setenv bootenv user.txt;" \
"fi;" \
"echo SD/MMC found on device ${mmcdev};" \
"if run loadbootenv; then " \
"echo Loaded environment from ${bootenv};" \
"run importbootenv;" \
"fi;" \
"if test -n $uenvcmd; then " \
"echo Running uenvcmd ...;" \
"run uenvcmd;" \
"fi;" \
"if run loadimage; then " \
"run mmcboot;" \
"fi;" \
"fi;" \
"run nandboot;" \
"setenv bootfile zImage;" \
"if run loadimage; then " \
"run loadfdt;" \
"run mmcbootz; " \
"fi; " \
#define CONFIG_AUTO_COMPLETE 1
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
#define CONFIG_SYS_PROMPT "OMAP3 beagleboard.org # "
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
#define CONFIG_SYS_ALT_MEMTEST 1
#define CONFIG_SYS_MEMTEST_START (0x82000000) /* memtest */
/* defaults */
#define CONFIG_SYS_MEMTEST_END (0x87FFFFFF) /* 128MB */
#define CONFIG_SYS_MEMTEST_SCRATCH (0x81000000) /* dummy address */
#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
/* load address */
/*
* OMAP3 has 12 GP timers, they can be driven by the system clock
* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
* This rate is divided by a local divisor.
*/
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
/* **** PISMO SUPPORT *** */
/* Configure the PISMO */
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#if defined(CONFIG_CMD_NAND)
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
#define CONFIG_ENV_IS_IN_NAND 1
#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_OMAP3_SPI
#define CONFIG_SYS_CACHELINE_SIZE 64
/* Defines for SPL */
#define CONFIG_SPL
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_NAND_SIMPLE
#define CONFIG_SPL_TEXT_BASE 0x40200800
#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_POWER_SUPPORT
#define CONFIG_SPL_OMAP3_ID_NAND
#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
/*
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
* 64 bytes before this address should be set aside for u-boot.img's
* header. That is 0x800FFFC0--0x80100000 should not be used for any
* other needs.
*/
#define CONFIG_SYS_TEXT_BASE 0x80100000
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#endif /* __CONFIG_H */