| /* |
| * Copyright (C) 2013 Samsung Electronics |
| * |
| * Configuration settings for the SAMSUNG EXYNOS5 board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_EXYNOS5_COMMON_H |
| #define __CONFIG_EXYNOS5_COMMON_H |
| |
| #define CONFIG_EXYNOS5 /* Exynos5 Family */ |
| |
| #include "exynos-common.h" |
| |
| #define CONFIG_SYS_CACHELINE_SIZE 64 |
| #define CONFIG_EXYNOS_SPL |
| |
| /* Allow tracing to be enabled */ |
| #define CONFIG_TRACE |
| #define CONFIG_CMD_TRACE |
| #define CONFIG_TRACE_BUFFER_SIZE (16 << 20) |
| #define CONFIG_TRACE_EARLY_SIZE (8 << 20) |
| #define CONFIG_TRACE_EARLY |
| #define CONFIG_TRACE_EARLY_ADDR 0x50000000 |
| |
| |
| /* Enable ACE acceleration for SHA1 and SHA256 */ |
| #define CONFIG_EXYNOS_ACE_SHA |
| #define CONFIG_SHA_HW_ACCEL |
| |
| /* Power Down Modes */ |
| #define S5P_CHECK_SLEEP 0x00000BAD |
| #define S5P_CHECK_DIDLE 0xBAD00000 |
| #define S5P_CHECK_LPA 0xABAD0000 |
| |
| /* Offset for inform registers */ |
| #define INFORM0_OFFSET 0x800 |
| #define INFORM1_OFFSET 0x804 |
| #define INFORM2_OFFSET 0x808 |
| #define INFORM3_OFFSET 0x80c |
| |
| /* select serial console configuration */ |
| #define CONFIG_BAUDRATE 115200 |
| #define EXYNOS5_DEFAULT_UART_OFFSET 0x010000 |
| #define CONFIG_SILENT_CONSOLE |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV |
| #define CONFIG_CONSOLE_MUX |
| |
| #define EXYNOS_DEVICE_SETTINGS \ |
| "stdin=serial\0" \ |
| "stdout=serial\0" \ |
| "stderr=serial\0" |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| EXYNOS_DEVICE_SETTINGS |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_HASH |
| |
| /* Thermal Management Unit */ |
| #define CONFIG_EXYNOS_TMU |
| #define CONFIG_CMD_DTT |
| #define CONFIG_TMU_CMD_DTT |
| |
| /* TPM */ |
| #define CONFIG_TPM |
| #define CONFIG_CMD_TPM |
| #define CONFIG_TPM_TIS_I2C |
| #define CONFIG_TPM_TIS_I2C_BUS_NUMBER 3 |
| #define CONFIG_TPM_TIS_I2C_SLAVE_ADDR 0x20 |
| |
| /* MMC SPL */ |
| #define COPY_BL2_FNPTR_ADDR 0x02020030 |
| #define CONFIG_SUPPORT_EMMC_BOOT |
| |
| #define CONFIG_SPL_LIBCOMMON_SUPPORT |
| #define CONFIG_SPL_GPIO_SUPPORT |
| |
| /* specific .lds file */ |
| #define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds" |
| |
| /* Boot Argument Buffer Size */ |
| /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE |
| #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x5E00000) |
| #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x3E00000) |
| |
| #define CONFIG_RD_LVL |
| |
| #define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE |
| #define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE |
| #define PHYS_SDRAM_2 (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE) |
| #define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE |
| #define PHYS_SDRAM_3 (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE)) |
| #define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE |
| #define PHYS_SDRAM_4 (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE)) |
| #define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE |
| #define PHYS_SDRAM_5 (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE)) |
| #define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE |
| #define PHYS_SDRAM_6 (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE)) |
| #define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE |
| #define PHYS_SDRAM_7 (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE)) |
| #define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE |
| #define PHYS_SDRAM_8 (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE)) |
| #define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE |
| |
| #define CONFIG_SYS_MONITOR_BASE 0x00000000 |
| |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| |
| #define CONFIG_SECURE_BL1_ONLY |
| |
| /* Secure FW size configuration */ |
| #ifdef CONFIG_SECURE_BL1_ONLY |
| #define CONFIG_SEC_FW_SIZE (8 << 10) /* 8KB */ |
| #else |
| #define CONFIG_SEC_FW_SIZE 0 |
| #endif |
| |
| /* Configuration of BL1, BL2, ENV Blocks on mmc */ |
| #define CONFIG_RES_BLOCK_SIZE (512) |
| #define CONFIG_BL1_SIZE (16 << 10) /*16 K reserved for BL1*/ |
| #define CONFIG_BL2_SIZE (512UL << 10UL) /* 512 KB */ |
| #define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */ |
| |
| #define CONFIG_BL1_OFFSET (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE) |
| #define CONFIG_BL2_OFFSET (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE) |
| |
| /* U-boot copy size from boot Media to DRAM.*/ |
| #define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512) |
| #define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512) |
| |
| #define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058 |
| #define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE) |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C_INIT_BOARD |
| #define CONFIG_SYS_I2C |
| #define CONFIG_CMD_I2C |
| #define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */ |
| #define CONFIG_SYS_I2C_S3C24X0 |
| #define CONFIG_I2C_MULTI_BUS |
| #define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0 |
| #define CONFIG_I2C_EDID |
| |
| /* SPI */ |
| #ifdef CONFIG_SPI_FLASH |
| #define CONFIG_EXYNOS_SPI |
| #define CONFIG_CMD_SF |
| #define CONFIG_CMD_SPI |
| #define CONFIG_SPI_FLASH_WINBOND |
| #define CONFIG_SPI_FLASH_GIGADEVICE |
| #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 |
| #define CONFIG_SF_DEFAULT_SPEED 50000000 |
| #define EXYNOS5_SPI_NUM_CONTROLLERS 5 |
| #define CONFIG_OF_SPI |
| #endif |
| |
| #ifdef CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_SPI_MODE SPI_MODE_0 |
| #define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE |
| #define CONFIG_ENV_SPI_BUS 1 |
| #define CONFIG_ENV_SPI_MAX_HZ 50000000 |
| #endif |
| |
| /* Ethernet Controllor Driver */ |
| #ifdef CONFIG_CMD_NET |
| #define CONFIG_SMC911X |
| #define CONFIG_SMC911X_BASE 0x5000000 |
| #define CONFIG_SMC911X_16_BIT |
| #define CONFIG_ENV_SROM_BANK 1 |
| #endif /*CONFIG_CMD_NET*/ |
| |
| /* Enable PXE Support */ |
| #ifdef CONFIG_CMD_NET |
| #define CONFIG_CMD_PXE |
| #define CONFIG_MENU |
| #endif |
| |
| /* SHA hashing */ |
| #define CONFIG_CMD_HASH |
| #define CONFIG_HASH_VERIFY |
| #define CONFIG_SHA1 |
| #define CONFIG_SHA256 |
| |
| /* Enable Time Command */ |
| #define CONFIG_CMD_TIME |
| |
| #define CONFIG_CMD_BOOTZ |
| |
| #define CONFIG_CMD_GPIO |
| |
| /* USB boot mode */ |
| #define CONFIG_USB_BOOTING |
| #define EXYNOS_COPY_USB_FNPTR_ADDR 0x02020070 |
| #define EXYNOS_USB_SECONDARY_BOOT 0xfeed0002 |
| #define EXYNOS_IRAM_SECONDARY_BASE 0x02020018 |
| |
| /* Enable FIT support and comparison */ |
| #define CONFIG_FIT |
| #define CONFIG_FIT_BEST_MATCH |
| |
| #endif /* __CONFIG_EXYNOS5_COMMON_H */ |