include/configs/cpci5200.h - github/trini/u-boot - Gitiles

 /*
  * (C) Copyright 2003-2004
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * SPDX-License-Identifier:	GPL-2.0+

  */

 /*************************************************************************
  * (c) 2005 esd gmbh Hannover
  *
  *
  * from IceCube.h file
  * by Reinhard Arlt reinhard.arlt@esd-electronics.com
  *
  *************************************************************************/

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_MPC5200		1	/* This is an MPC5200 CPU */
 #define CONFIG_ICECUBE		1	/* ... on IceCube board	  */
 #define CONFIG_CPCI5200		1	/* ... on CPCI5200  board */
 #define CONFIG_MPC5200_DDR	1	/* ... use DDR RAM	  */

 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xFFF00000	/* Standard: boot high */
 #endif

 #define CONFIG_SYS_MPC5XXX_CLKIN	33000000	/* ... running at 33.000000MHz */

 #define CONFIG_HIGH_BATS	1	/* High BATs supported 	  */

 /*
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
 #define CONFIG_BAUDRATE		9600	/* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */
 #if 1
 #define CONFIG_PCI		1
 #if 1
 #define CONFIG_PCI_PNP		1
 #endif
 #define CONFIG_PCI_SCAN_SHOW	1
 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1

 #define CONFIG_PCI_MEM_BUS	0x40000000
 #define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
 #define CONFIG_PCI_MEM_SIZE	0x10000000

 #define CONFIG_PCI_IO_BUS	0x50000000
 #define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
 #define CONFIG_PCI_IO_SIZE	0x01000000
 #endif

 #define CONFIG_MII
 #if 0				/* test-only !!! */
 #define CONFIG_EEPRO100		1
 #define CONFIG_SYS_RX_ETH_BUFFER	8	/* use 8 rx buffer on eepro100	*/
 #define CONFIG_NS8382X		1
 #endif

 /* Partitions */
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION

 /* USB */
 #if 0
 #define CONFIG_USB_OHCI
 #define CONFIG_USB_STORAGE
 #endif

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
 #endif

 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_BSP
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_DATE

 #if (CONFIG_SYS_TEXT_BASE == 0xFF000000)	/* Boot low with 16 MB Flash */
 #   define CONFIG_SYS_LOWBOOT		1
 #   define CONFIG_SYS_LOWBOOT16	1
 #endif
 #if (CONFIG_SYS_TEXT_BASE == 0xFF800000)	/* Boot low with  8 MB Flash */
 #   define CONFIG_SYS_LOWBOOT		1
 #   define CONFIG_SYS_LOWBOOT08	1
 #endif

 /*
  * Autobooting
  */
 #define CONFIG_BOOTDELAY	3	/* autoboot after 5 seconds */

 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Welcome to esd CPU CPCI/5200;" \
 	"echo"

 #undef	CONFIG_BOOTARGS

 #define	CONFIG_EXTRA_ENV_SETTINGS \
 	"netdev=eth0\0" \
 	"flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \
 	"flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \
 	"net_vxworks=phypower 1;sleep 2;tftp ${loadaddr} ${image};run vxworks_args;bootvx\0" \
 	"vxworks_args=setenv bootargs fec(0,0)${host}:${image} h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script}\0" \
 	"ata_vxworks_args=setenv bootargs /ata0/vxWorks h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script} o=fec0 \0" \
 	"loadaddr=01000000\0" \
 	"serverip=192.168.2.99\0" \
 	"gatewayip=10.0.0.79\0" \
 	"user=mu\0" \
 	"target=cpci5200.esd\0" \
 	"script=cpci5200.bat\0" \
 	"image=/tftpboot/vxWorks_cpci5200\0" \
 	"ipaddr=10.0.13.196\0" \
 	"netmask=255.255.0.0\0" \
 	""

 #define CONFIG_BOOTCOMMAND	"run flash_vxworks0"

 #define CONFIG_RTC_M48T35A	1	/* ST Electronics M48 timekeeper */
 #define CONFIG_SYS_NVRAM_BASE_ADDR	0xfd010000
 #define CONFIG_SYS_NVRAM_SIZE		32*1024

 /*
  * IPB Bus clocking configuration.
  */
 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
 /*
  * I2C configuration
  */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support */
 #define CONFIG_SYS_I2C_MODULE		1	/* Select I2C module #1 or #2 */

 #define CONFIG_SYS_I2C_SPEED		86000	/* 100 kHz */
 #define CONFIG_SYS_I2C_SLAVE		0x7F

 /*
  * EEPROM configuration
  */
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
 #define CONFIG_SYS_I2C_MULTI_EEPROMS		1
 /*
  * Flash configuration
  */

 #define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant	     */
 #define CONFIG_SYS_FLASH_BASE		0xFE000000
 #define CONFIG_SYS_FLASH_SIZE		0x02000000
 #define CONFIG_SYS_FLASH_INCREMENT	0x01000000
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00000000)
 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max num of memory banks	*/
 #define CONFIG_SYS_MAX_FLASH_SECT	128

 #define CONFIG_SYS_FLASH_PROTECTION	1	/* use hardware protection	     */
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)  */

 #define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/

 /*
  * Environment settings
  */
 #if 1				/* test-only */
 #define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_SIZE		0x20000
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_OVERWRITE	1
 #else
 #define CONFIG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
 #define CONFIG_ENV_OFFSET		0x0000	/* environment starts at the beginning of the EEPROM */
 #define CONFIG_ENV_SIZE		0x0400	/* 8192 bytes may be used for env vars */
 				   /* total size of a CAT24WC32 is 8192 bytes */
 #define CONFIG_ENV_OVERWRITE	1
 #endif

 /*
  * Memory map
  */
 #define CONFIG_SYS_MBAR		0xF0000000
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_DEFAULT_MBAR	0x80000000

 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
 #define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE	/* Size of used area in DPRAM */

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT		1
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
 #define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 /*
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC	1
 #define CONFIG_MPC5xxx_FEC_MII100
 /*
  * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
  */
 /* #define CONFIG_FEC_10MBIT 1 */
 #define CONFIG_PHY_ADDR		0x00
 #define CONFIG_UDP_CHECKSUM	1

 /*
  * GPIO configuration
  */
 #define CONFIG_SYS_GPS_PORT_CONFIG	0x01052444

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP		/* undef to save memory	    */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/

 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */

 #define CONFIG_SYS_VXWORKS_MAC_PTR	0x00000000	/* Pass Ethernet MAC to VxWorks */

 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
 #if defined(CONFIG_CMD_KGDB)
 #  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif

 /*
  * Various low-level settings
  */
 #define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL		HID0_ICE

 #define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
 #define CONFIG_SYS_BOOTCS_CFG		0x0004DD00

 #define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE

 #define CONFIG_SYS_CS1_START		0xfd000000
 #define CONFIG_SYS_CS1_SIZE		0x00010000
 #define CONFIG_SYS_CS1_CFG		0x10101410

 #define CONFIG_SYS_CS3_START		0xfd010000
 #define CONFIG_SYS_CS3_SIZE		0x00010000
 #define CONFIG_SYS_CS3_CFG		0x10109410

 #define CONFIG_SYS_CS_BURST		0x00000000
 #define CONFIG_SYS_CS_DEADCYCLE	0x33333333

 #define CONFIG_SYS_RESET_ADDRESS	0xff000000

 /*-----------------------------------------------------------------------
  * USB stuff
  *-----------------------------------------------------------------------
  */
 #define CONFIG_USB_CLOCK	0x0001BBBB
 #define CONFIG_USB_CONFIG	0x00001000

 /*-----------------------------------------------------------------------
  * IDE/ATA stuff Supports IDE harddisk
  *-----------------------------------------------------------------------
  */

 #undef	CONFIG_IDE_8xx_PCCARD	/* Use IDE with PC Card Adapter */

 #undef	CONFIG_IDE_8xx_DIRECT	/* Direct IDE	 not supported	*/
 #undef	CONFIG_IDE_LED		/* LED	 for ide not supported	*/

 #define	CONFIG_IDE_RESET	/* reset for ide supported	*/
 #define CONFIG_IDE_PREINIT

 #define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
 #define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/

 #define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000

 #define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA

 /* Offset for data I/O			*/
 #define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)

 /* Offset for normal register accesses	*/
 #define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)

 /* Offset for alternate registers	*/
 #define CONFIG_SYS_ATA_ALT_OFFSET	(0x005C)

 /* Interval between registers						     */
 #define CONFIG_SYS_ATA_STRIDE		4

 /*-----------------------------------------------------------------------
  * CPLD stuff
  */
 #define CONFIG_SYS_FPGA_XC95XL		1	/* using Xilinx XC95XL CPLD	 */
 #define CONFIG_SYS_FPGA_MAX_SIZE	32*1024	/* 32kByte is enough for CPLD	 */

 /* CPLD program pin configuration */
 #define CONFIG_SYS_FPGA_PRG		0x20000000	/* JTAG TMS pin (ppc output)	       */
 #define CONFIG_SYS_FPGA_CLK		0x10000000	/* JTAG TCK pin (ppc output)	       */
 #define CONFIG_SYS_FPGA_DATA		0x20000000	/* JTAG TDO->TDI data pin (ppc output) */
 #define CONFIG_SYS_FPGA_DONE		0x10000000	/* JTAG TDI->TDO pin (ppc input)       */

 #define JTAG_GPIO_ADDR_TMS	(CONFIG_SYS_MBAR + 0xB10)	/* JTAG TMS pin (GPS data out value reg.)      */
 #define JTAG_GPIO_ADDR_TCK	(CONFIG_SYS_MBAR + 0xC0C)	/* JTAG TCK pin (GPW data out value reg.)      */
 #define JTAG_GPIO_ADDR_TDI	(CONFIG_SYS_MBAR + 0xC0C)	/* JTAG TDO->TDI pin (GPW data out value reg.) */
 #define JTAG_GPIO_ADDR_TDO	(CONFIG_SYS_MBAR + 0xB14)	/* JTAG TDI->TDO pin (GPS data in value reg.)  */

 #define JTAG_GPIO_ADDR_CFG	(CONFIG_SYS_MBAR + 0xB00)
 #define JTAG_GPIO_CFG_SET	0x00000000
 #define JTAG_GPIO_CFG_RESET	0x00F00000

 #define JTAG_GPIO_ADDR_EN_TMS	(CONFIG_SYS_MBAR + 0xB04)
 #define JTAG_GPIO_TMS_EN_SET	0x20000000	/* Enable for GPIO */
 #define JTAG_GPIO_TMS_EN_RESET	0x00000000
 #define JTAG_GPIO_ADDR_DDR_TMS	(CONFIG_SYS_MBAR + 0xB0C)
 #define JTAG_GPIO_TMS_DDR_SET	0x20000000	/* Set as output   */
 #define JTAG_GPIO_TMS_DDR_RESET 0x00000000

 #define JTAG_GPIO_ADDR_EN_TCK	(CONFIG_SYS_MBAR + 0xC00)
 #define JTAG_GPIO_TCK_EN_SET	0x20000000	/* Enable for GPIO */
 #define JTAG_GPIO_TCK_EN_RESET	0x00000000
 #define JTAG_GPIO_ADDR_DDR_TCK	(CONFIG_SYS_MBAR + 0xC08)
 #define JTAG_GPIO_TCK_DDR_SET	0x20000000	/* Set as output   */
 #define JTAG_GPIO_TCK_DDR_RESET 0x00000000

 #define JTAG_GPIO_ADDR_EN_TDI	(CONFIG_SYS_MBAR + 0xC00)
 #define JTAG_GPIO_TDI_EN_SET	0x10000000	/* Enable as GPIO  */
 #define JTAG_GPIO_TDI_EN_RESET	0x00000000
 #define JTAG_GPIO_ADDR_DDR_TDI	(CONFIG_SYS_MBAR + 0xC08)
 #define JTAG_GPIO_TDI_DDR_SET	0x10000000	/* Set as output   */
 #define JTAG_GPIO_TDI_DDR_RESET 0x00000000

 #define JTAG_GPIO_ADDR_EN_TDO	(CONFIG_SYS_MBAR + 0xB04)
 #define JTAG_GPIO_TDO_EN_SET	0x10000000	/* Enable as GPIO  */
 #define JTAG_GPIO_TDO_EN_RESET	0x00000000
 #define JTAG_GPIO_ADDR_DDR_TDO	(CONFIG_SYS_MBAR + 0xB0C)
 #define JTAG_GPIO_TDO_DDR_SET	0x00000000
 #define JTAG_GPIO_TDO_DDR_RESET 0x10000000	/* Set as input	   */

 #endif				/* __CONFIG_H */
	/*
	* (C) Copyright 2003-2004
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* SPDX-License-Identifier: GPL-2.0+

	*/

	/*************************************************************************
	* (c) 2005 esd gmbh Hannover
	*
	*
	* from IceCube.h file
	* by Reinhard Arlt reinhard.arlt@esd-electronics.com
	*
	*************************************************************************/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
	#define CONFIG_ICECUBE 1 /* ... on IceCube board */
	#define CONFIG_CPCI5200 1 /* ... on CPCI5200 board */
	#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */

	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */
	#endif

	#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */

	#define CONFIG_HIGH_BATS 1 /* High BATs supported */

	/*
	* Serial console configuration
	*/
	#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
	#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */
	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }

	/*
	* PCI Mapping:
	* 0x40000000 - 0x4fffffff - PCI Memory
	* 0x50000000 - 0x50ffffff - PCI IO Space
	*/
	#if 1
	#define CONFIG_PCI 1
	#if 1
	#define CONFIG_PCI_PNP 1
	#endif
	#define CONFIG_PCI_SCAN_SHOW 1
	#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1

	#define CONFIG_PCI_MEM_BUS 0x40000000
	#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
	#define CONFIG_PCI_MEM_SIZE 0x10000000

	#define CONFIG_PCI_IO_BUS 0x50000000
	#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
	#define CONFIG_PCI_IO_SIZE 0x01000000
	#endif

	#define CONFIG_MII
	#if 0 /* test-only !!! */
	#define CONFIG_EEPRO100 1
	#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
	#define CONFIG_NS8382X 1
	#endif

	/* Partitions */
	#define CONFIG_MAC_PARTITION
	#define CONFIG_DOS_PARTITION

	/* USB */
	#if 0
	#define CONFIG_USB_OHCI
	#define CONFIG_USB_STORAGE
	#endif

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#if defined(CONFIG_PCI)
	#define CONFIG_CMD_PCI
	#endif

	#define CONFIG_CMD_EEPROM
	#define CONFIG_CMD_FAT
	#define CONFIG_CMD_IDE
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_BSP
	#define CONFIG_CMD_ELF
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_DATE

	#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
	# define CONFIG_SYS_LOWBOOT 1
	# define CONFIG_SYS_LOWBOOT16 1
	#endif
	#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
	# define CONFIG_SYS_LOWBOOT 1
	# define CONFIG_SYS_LOWBOOT08 1
	#endif

	/*
	* Autobooting
	*/
	#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */

	#define CONFIG_PREBOOT "echo;" \
	"echo Welcome to esd CPU CPCI/5200;" \
	"echo"

	#undef CONFIG_BOOTARGS

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \
	"flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \
	"net_vxworks=phypower 1;sleep 2;tftp ${loadaddr} ${image};run vxworks_args;bootvx\0" \
	"vxworks_args=setenv bootargs fec(0,0)${host}:${image} h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script}\0" \
	"ata_vxworks_args=setenv bootargs /ata0/vxWorks h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script} o=fec0 \0" \
	"loadaddr=01000000\0" \
	"serverip=192.168.2.99\0" \
	"gatewayip=10.0.0.79\0" \
	"user=mu\0" \
	"target=cpci5200.esd\0" \
	"script=cpci5200.bat\0" \
	"image=/tftpboot/vxWorks_cpci5200\0" \
	"ipaddr=10.0.13.196\0" \
	"netmask=255.255.0.0\0" \
	""

	#define CONFIG_BOOTCOMMAND "run flash_vxworks0"

	#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */
	#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfd010000
	#define CONFIG_SYS_NVRAM_SIZE 32*1024

	/*
	* IPB Bus clocking configuration.
	*/
	#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
	/*
	* I2C configuration
	*/
	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
	#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */

	#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */
	#define CONFIG_SYS_I2C_SLAVE 0x7F

	/*
	* EEPROM configuration
	*/
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
	#define CONFIG_SYS_I2C_MULTI_EEPROMS 1
	/*
	* Flash configuration
	*/

	#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
	#define CONFIG_SYS_FLASH_BASE 0xFE000000
	#define CONFIG_SYS_FLASH_SIZE 0x02000000
	#define CONFIG_SYS_FLASH_INCREMENT 0x01000000
	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00000000)
	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 128

	#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */

	#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */

	/*
	* Environment settings
	*/
	#if 1 /* test-only */
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_SIZE 0x20000
	#define CONFIG_ENV_SECT_SIZE 0x20000
	#define CONFIG_ENV_OVERWRITE 1
	#else
	#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
	#define CONFIG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */
	#define CONFIG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars */
	/* total size of a CAT24WC32 is 8192 bytes */
	#define CONFIG_ENV_OVERWRITE 1
	#endif

	/*
	* Memory map
	*/
	#define CONFIG_SYS_MBAR 0xF0000000
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_DEFAULT_MBAR 0x80000000

	/* Use SRAM until RAM will be available */
	#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
	#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	# define CONFIG_SYS_RAMBOOT 1
	#endif

	#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*
	* Ethernet configuration
	*/
	#define CONFIG_MPC5xxx_FEC 1
	#define CONFIG_MPC5xxx_FEC_MII100
	/*
	* Define CONFIG_FEC_10MBIT to force FEC at 10Mb
	*/
	/* #define CONFIG_FEC_10MBIT 1 */
	#define CONFIG_PHY_ADDR 0x00
	#define CONFIG_UDP_CHECKSUM 1

	/*
	* GPIO configuration
	*/
	#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */

	#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */

	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	/*
	* Various low-level settings
	*/
	#define CONFIG_SYS_HID0_INIT HID0_ICE \| HID0_ICFI
	#define CONFIG_SYS_HID0_FINAL HID0_ICE

	#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
	#define CONFIG_SYS_BOOTCS_CFG 0x0004DD00

	#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE

	#define CONFIG_SYS_CS1_START 0xfd000000
	#define CONFIG_SYS_CS1_SIZE 0x00010000
	#define CONFIG_SYS_CS1_CFG 0x10101410

	#define CONFIG_SYS_CS3_START 0xfd010000
	#define CONFIG_SYS_CS3_SIZE 0x00010000
	#define CONFIG_SYS_CS3_CFG 0x10109410

	#define CONFIG_SYS_CS_BURST 0x00000000
	#define CONFIG_SYS_CS_DEADCYCLE 0x33333333

	#define CONFIG_SYS_RESET_ADDRESS 0xff000000

	/*-----------------------------------------------------------------------
	* USB stuff
	*-----------------------------------------------------------------------
	*/
	#define CONFIG_USB_CLOCK 0x0001BBBB
	#define CONFIG_USB_CONFIG 0x00001000

	/*-----------------------------------------------------------------------
	* IDE/ATA stuff Supports IDE harddisk
	*-----------------------------------------------------------------------
	*/

	#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */

	#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
	#undef CONFIG_IDE_LED /* LED for ide not supported */

	#define CONFIG_IDE_RESET /* reset for ide supported */
	#define CONFIG_IDE_PREINIT

	#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
	#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */

	#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000

	#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA

	/* Offset for data I/O */
	#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)

	/* Offset for normal register accesses */
	#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)

	/* Offset for alternate registers */
	#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)

	/* Interval between registers */
	#define CONFIG_SYS_ATA_STRIDE 4

	/*-----------------------------------------------------------------------
	* CPLD stuff
	*/
	#define CONFIG_SYS_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
	#define CONFIG_SYS_FPGA_MAX_SIZE 321024 / 32kByte is enough for CPLD */

	/* CPLD program pin configuration */
	#define CONFIG_SYS_FPGA_PRG 0x20000000 /* JTAG TMS pin (ppc output) */
	#define CONFIG_SYS_FPGA_CLK 0x10000000 /* JTAG TCK pin (ppc output) */
	#define CONFIG_SYS_FPGA_DATA 0x20000000 /* JTAG TDO->TDI data pin (ppc output) */
	#define CONFIG_SYS_FPGA_DONE 0x10000000 /* JTAG TDI->TDO pin (ppc input) */

	#define JTAG_GPIO_ADDR_TMS (CONFIG_SYS_MBAR + 0xB10) /* JTAG TMS pin (GPS data out value reg.) */
	#define JTAG_GPIO_ADDR_TCK (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TCK pin (GPW data out value reg.) */
	#define JTAG_GPIO_ADDR_TDI (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TDO->TDI pin (GPW data out value reg.) */
	#define JTAG_GPIO_ADDR_TDO (CONFIG_SYS_MBAR + 0xB14) /* JTAG TDI->TDO pin (GPS data in value reg.) */

	#define JTAG_GPIO_ADDR_CFG (CONFIG_SYS_MBAR + 0xB00)
	#define JTAG_GPIO_CFG_SET 0x00000000
	#define JTAG_GPIO_CFG_RESET 0x00F00000

	#define JTAG_GPIO_ADDR_EN_TMS (CONFIG_SYS_MBAR + 0xB04)
	#define JTAG_GPIO_TMS_EN_SET 0x20000000 /* Enable for GPIO */
	#define JTAG_GPIO_TMS_EN_RESET 0x00000000
	#define JTAG_GPIO_ADDR_DDR_TMS (CONFIG_SYS_MBAR + 0xB0C)
	#define JTAG_GPIO_TMS_DDR_SET 0x20000000 /* Set as output */
	#define JTAG_GPIO_TMS_DDR_RESET 0x00000000

	#define JTAG_GPIO_ADDR_EN_TCK (CONFIG_SYS_MBAR + 0xC00)
	#define JTAG_GPIO_TCK_EN_SET 0x20000000 /* Enable for GPIO */
	#define JTAG_GPIO_TCK_EN_RESET 0x00000000
	#define JTAG_GPIO_ADDR_DDR_TCK (CONFIG_SYS_MBAR + 0xC08)
	#define JTAG_GPIO_TCK_DDR_SET 0x20000000 /* Set as output */
	#define JTAG_GPIO_TCK_DDR_RESET 0x00000000

	#define JTAG_GPIO_ADDR_EN_TDI (CONFIG_SYS_MBAR + 0xC00)
	#define JTAG_GPIO_TDI_EN_SET 0x10000000 /* Enable as GPIO */
	#define JTAG_GPIO_TDI_EN_RESET 0x00000000
	#define JTAG_GPIO_ADDR_DDR_TDI (CONFIG_SYS_MBAR + 0xC08)
	#define JTAG_GPIO_TDI_DDR_SET 0x10000000 /* Set as output */
	#define JTAG_GPIO_TDI_DDR_RESET 0x00000000

	#define JTAG_GPIO_ADDR_EN_TDO (CONFIG_SYS_MBAR + 0xB04)
	#define JTAG_GPIO_TDO_EN_SET 0x10000000 /* Enable as GPIO */
	#define JTAG_GPIO_TDO_EN_RESET 0x00000000
	#define JTAG_GPIO_ADDR_DDR_TDO (CONFIG_SYS_MBAR + 0xB0C)
	#define JTAG_GPIO_TDO_DDR_SET 0x00000000
	#define JTAG_GPIO_TDO_DDR_RESET 0x10000000 /* Set as input */

	#endif /* __CONFIG_H */