blob: 28ae9fa9e31be2189159a2a5a3a8e47a8f2365e0 [file] [log] [blame]
/*
* (C) Copyright 2000
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* Pantelis Antoniou, Intracom S.A., panto@intracom.gr
* U-Boot port on NetVia board
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC850 1 /* This is a MPC850 CPU */
#define CONFIG_NETVIA 1 /* ...on a NetVia board */
#undef CONFIG_NETVIA_PLL_CLOCK /* PLL or fixed crystal clock */
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
#ifdef CONFIG_NETVIA_PLL_CLOCK
/* XXX make sure that you calculate these two correctly */
#define CFG_GCLK_MF 1350
#define CONFIG_8xx_GCLK_FREQ 44236800
#else
#define CFG_GCLK_MF 1
#define CONFIG_8xx_GCLK_FREQ 50000000
#endif
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"tftpboot; " \
"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
"bootm"
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_STATUS_LED 1 /* Status LED enabled */
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
#undef CONFIG_MAC_PARTITION
#undef CONFIG_DOS_PARTITION
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP )
#define CONFIG_BOARD_PRE_INIT
#define CONFIG_MISC_INIT_R
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_MEMTEST_START 0x0300000 /* memtest works on */
#define CFG_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */
#define CFG_LOAD_ADDR 0x100000 /* default load address */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CFG_IMMR 0xFF000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
#define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0x40000000
#if defined(DEBUG)
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#endif
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
#define CFG_ENV_SECT_SIZE 0x10000
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
#ifndef CONFIG_CAN_DRIVER
#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
#else /* we must activate GPL5 in the SIUMCR for CAN */
#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
#endif /* CONFIG_CAN_DRIVER */
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* RTCSC - Real-Time Clock Status and Control Register 11-27
*-----------------------------------------------------------------------
*/
#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CFG_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit
*
*/
#define CFG_PLPRCR ( ((CFG_GCLK_MF-1) << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF11
#define CFG_SCCR (SCCR_TBS | \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
/*#define CFG_DER 0x2002000F*/
#define CFG_DER 0
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
/* used to re-map FLASH both when starting from SRAM or FLASH:
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */
#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX)
#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
/*
* BR1/2 and OR1/2 (4MByte Flash Bank x 2)
*
*/
#define FLASH0_SIZE 0x00400000 /* 4MByte */
#define FLASH0_BASE 0xF0000000
#define CFG_OR1_PRELIM ((0xFFFFFFFFLU & ~(FLASH0_SIZE - 1)) | OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX)
#define CFG_BR1_PRELIM ((FLASH0_BASE & BR_BA_MSK) | BR_PS_32 | BR_V)
#define FLASH1_SIZE 0x00400000
#define FLASH1_BASE 0xF0400000
#define CFG_OR2_PRELIM ((0xFFFFFFFFLU & ~(FLASH1_SIZE - 1)) | OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX)
#define CFG_BR2_PRELIM ((FLASH1_BASE & BR_BA_MSK) | BR_PS_32 | BR_V)
/*
* BR3 and OR3 (SDRAM)
*
*/
#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
#define CFG_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS)
#define CFG_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CFG_OR_TIMING_SDRAM)
#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_PS_32 | BR_V)
/*
* BR6 (External register)
* 16 bit port size - leds are at high 8 bits
*/
#define EXTREG_BASE 0x30000000 /* external register */
#define EXTREG_SIZE 0x00010000 /* max 64K */
#define CFG_OR6_PRELIM ((0xFFFFFFFFLU & ~(EXTREG_SIZE - 1)) | OR_CSNT_SAM | OR_BI | OR_SCY_15_CLK | OR_TRLX)
#define CFG_BR6_PRELIM ((EXTREG_BASE & BR_BA_MSK) | BR_PS_32 | BR_V)
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
#define CFG_MAMR_PTA 208
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
/* 9 column SDRAM */
#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
/* Ethernet at SCC2 */
#define CONFIG_SCC2_ENET
#define CONFIG_ARTOS /* include ARTOS support */
#endif /* __CONFIG_H */