| /* |
| * MOUSSE/MPC8240 Board definitions. |
| * For more info, see http://www.vooha.com/ |
| * |
| * (C) Copyright 2000 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * (C) Copyright 2001 |
| * James Dougherty (jfd@cs.stanford.edu) |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __MOUSSE_H |
| #define __MOUSSE_H |
| |
| /* System addresses */ |
| |
| #define PCI_SPECIAL_BASE 0xfe000000 |
| #define PCI_SPECIAL_SIZE 0x01000000 |
| |
| /* PORTX Device Addresses for Mousse */ |
| |
| #define PORTX_DEV_BASE 0xff000000 |
| #define PORTX_DEV_SIZE 0x01000000 |
| |
| #define ENET_DEV_BASE 0x80000000 |
| |
| #define PLD_REG_BASE (PORTX_DEV_BASE | 0xe09000) |
| #define PLD_REG(off) (*(volatile unsigned char *) \ |
| (PLD_REG_BASE + (off))) |
| |
| #define PLD_REVID_B1 0x7f |
| #define PLD_REVID_B2 0x01 |
| |
| /* MPLD */ |
| #define SYS_HARD_RESET() { for (;;) PLD_REG(0) = 0; } /* clr 0x80 bit */ |
| #define SYS_REVID_GET() ((int) PLD_REG(0) & 0x7f) |
| #define SYS_LED_OFF() (PLD_REG(1) |= 0x80) |
| #define SYS_LED_ON() (PLD_REG(1) &= ~0x80) |
| #define SYS_WATCHDOG_IRQ3() (PLD_REG(2) |= 0x80) |
| #define SYS_WATCHDOG_RESET() (PLD_REG(2) &= ~0x80) |
| #define SYS_TOD_PROTECT() (PLD_REG(3) |= 0x80) |
| #define SYS_TOD_UNPROTECT() (PLD_REG(3) &= ~0x80) |
| |
| /* SGS M48T59Y */ |
| #define TOD_BASE (PORTX_DEV_BASE | 0xe0a000) |
| #define TOD_REG_BASE (TOD_BASE | 0x1ff0) |
| #define TOD_NVRAM_BASE TOD_BASE |
| #define TOD_NVRAM_SIZE 0x1ff0 |
| #define TOD_NVRAM_LIMIT (TOD_NVRAM_BASE + TOD_NVRAM_SIZE) |
| |
| /* NS16552 SIO */ |
| #define SERIAL_BASE(_x) (PORTX_DEV_BASE | 0xe08000 | ((_x) ? 0 : 0x80)) |
| #define N_SIO_CHANNELS 2 |
| #define N_COM_PORTS N_SIO_CHANNELS |
| |
| /* |
| * On-board Dec21143 PCI Ethernet |
| * Note: The PCI MBAR chosen here was used from MPC8240UM which states |
| * that PCI memory is at: 0x80000 - 0xFDFFFFFF, if AMBOR[CPU_FD_ALIAS] |
| * is set, then PCI memory maps 1-1 with this address range in the |
| * correct byte order. |
| */ |
| #define PCI_ENET_IOADDR 0x80000000 |
| #define PCI_ENET_MEMADDR 0x80000000 |
| |
| /* |
| * Flash Memory Layout |
| * |
| * 2 MB Flash Bank 0 runs in 8-bit mode. In Flash Bank 0, the 32 kB |
| * sector SA3 is obscured by the 32 kB serial/TOD access space, and |
| * the 64 kB sectors SA19-SA26 are obscured by the 512 kB PLCC |
| * containing the fixed boot ROM. (If the 512 kB PLCC is |
| * deconfigured by jumper, this window to Flash Bank 0 becomes |
| * visible, but it still contains the fixed boot code and should be |
| * considered read-only). Flash Bank 0 sectors SA0 (16 kB), SA1 (8 |
| * kB), and SA2 (8 kB) are currently unused. |
| * |
| * 2 MB Flash Bank 1 runs in 16-bit mode. Flash Bank 1 is fully |
| * usable, but it's a 16-bit wide device on a 64-bit bus. Therefore |
| * 16-bit words only exist at addresses that are multiples of 8. All |
| * PROM data and control addresses must be multiplied by 8. |
| * |
| * See flashMap.c for description of flash filesystem layout. |
| */ |
| |
| /* |
| * FLASH memory address space: 8-bit wide FLASH memory spaces. |
| */ |
| #define FLASH0_SEG0_START 0xffe00000 /* Baby 32Kb segment */ |
| #define FLASH0_SEG0_END 0xffe07fff /* 16 kB + 8 kB + 8 kB */ |
| #define FLASH0_SEG0_SIZE 0x00008000 /* (sectors SA0-SA2) */ |
| |
| #define FLASH0_SEG1_START 0xffe10000 /* 1MB - 64Kb FLASH0 seg */ |
| #define FLASH0_SEG1_END 0xffefffff /* 960 kB */ |
| #define FLASH0_SEG1_SIZE 0x000f0000 |
| |
| #define FLASH0_SEG2_START 0xfff00000 /* Boot Loader stored here */ |
| #define FLASH0_SEG2_END 0xfff7ffff /* 512 kB FLASH0/PLCC seg */ |
| #define FLASH0_SEG2_SIZE 0x00080000 |
| |
| #define FLASH0_SEG3_START 0xfff80000 /* 512 kB FLASH0 seg */ |
| #define FLASH0_SEG3_END 0xffffffff |
| #define FLASH0_SEG3_SIZE 0x00080000 |
| |
| /* Where Kahlua starts */ |
| #define FLASH_RESET_VECT 0xfff00100 |
| |
| /* |
| * CHRP / PREP (MAP A/B) definitions. |
| */ |
| |
| #define PREP_REG_ADDR 0x80000cf8 /* MPC107 Config, Map A */ |
| #define PREP_REG_DATA 0x80000cfc /* MPC107 Config, Map A */ |
| /* MPC107 (MPC8240 internal EUMBBAR mapped) */ |
| #define CHRP_REG_ADDR 0xfec00000 /* MPC106 Config, Map B */ |
| #define CHRP_REG_DATA 0xfee00000 /* MPC106 Config, Map B */ |
| |
| /* |
| * Mousse PCI IDSEL Assignments (Device Number) |
| */ |
| #define MOUSSE_IDSEL_ENET 13 /* On-board 21143 Ethernet */ |
| #define MOUSSE_IDSEL_LPCI 14 /* On-board PCI slot */ |
| #define MOUSSE_IDSEL_82371 15 /* That other thing */ |
| #define MOUSSE_IDSEL_CPCI2 31 /* CPCI slot 2 */ |
| #define MOUSSE_IDSEL_CPCI3 30 /* CPCI slot 3 */ |
| #define MOUSSE_IDSEL_CPCI4 29 /* CPCI slot 4 */ |
| #define MOUSSE_IDSEL_CPCI5 28 /* CPCI slot 5 */ |
| #define MOUSSE_IDSEL_CPCI6 27 /* CPCI slot 6 */ |
| |
| /* |
| * Mousse Interrupt Mapping: |
| * |
| * IRQ1 Enet (intA|intB|intC|intD) |
| * IRQ2 CPCI intA (See below) |
| * IRQ3 Local PCI slot intA|intB|intC|intD |
| * IRQ4 COM1 Serial port (Actually higher addressed port on duart) |
| * |
| * PCI Interrupt Mapping in CPCI chassis: |
| * |
| * | CPCI Slot |
| * | 1 (CPU) 2 3 4 5 6 |
| * -----------+--------+-------+-------+-------+-------+-------+ |
| * intA | X X X |
| * intB | X X X |
| * intC | X X X |
| * intD | X X X |
| */ |
| |
| |
| #define EPIC_VECTOR_EXT0 0 |
| #define EPIC_VECTOR_EXT1 1 |
| #define EPIC_VECTOR_EXT2 2 |
| #define EPIC_VECTOR_EXT3 3 |
| #define EPIC_VECTOR_EXT4 4 |
| #define EPIC_VECTOR_TM0 16 |
| #define EPIC_VECTOR_TM1 17 |
| #define EPIC_VECTOR_TM2 18 |
| #define EPIC_VECTOR_TM3 19 |
| #define EPIC_VECTOR_I2C 20 |
| #define EPIC_VECTOR_DMA0 21 |
| #define EPIC_VECTOR_DMA1 22 |
| #define EPIC_VECTOR_I2O 23 |
| |
| |
| #define INT_VEC_IRQ0 0 |
| #define INT_NUM_IRQ0 INT_VEC_IRQ0 |
| #define MOUSSE_IRQ_ENET EPIC_VECTOR_EXT1 /* Hardwired */ |
| #define MOUSSE_IRQ_CPCI EPIC_VECTOR_EXT2 /* Hardwired */ |
| #define MOUSSE_IRQ_LPCI EPIC_VECTOR_EXT3 /* Hardwired */ |
| #define MOUSSE_IRQ_DUART EPIC_VECTOR_EXT4 /* Hardwired */ |
| |
| /* Onboard DEC 21143 Ethernet */ |
| #define PCI_ENET_MEMADDR 0x80000000 |
| #define PCI_ENET_IOADDR 0x80000000 |
| |
| /* Some other PCI device */ |
| #define PCI_SLOT_MEMADDR 0x81000000 |
| #define PCI_SLOT_IOADDR 0x81000000 |
| |
| /* Promise ATA66 PCI Device (ATA controller) */ |
| #define PROMISE_MBAR0 0xa0000000 |
| #define PROMISE_MBAR1 (PROMISE_MBAR0 + 0x1000) |
| #define PROMISE_MBAR2 (PROMISE_MBAR0 + 0x2000) |
| #define PROMISE_MBAR3 (PROMISE_MBAR0 + 0x3000) |
| #define PROMISE_MBAR4 (PROMISE_MBAR0 + 0x4000) |
| #define PROMISE_MBAR5 (PROMISE_MBAR0 + 0x5000) |
| |
| /* ATA/66 Controller offsets */ |
| #define CONFIG_SYS_ATA_BASE_ADDR PROMISE_MBAR0 |
| #define CONFIG_SYS_IDE_MAXBUS 2 /* ide0/ide1 */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 2 /* 2 drives per controller */ |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0 |
| #define CONFIG_SYS_ATA_IDE1_OFFSET 0x3000 |
| /* |
| * Definitions for accessing IDE controller registers |
| */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0 |
| #define CONFIG_SYS_ATA_REG_OFFSET 0 |
| #define CONFIG_SYS_ATA_ALT_OFFSET (0x1000) |
| |
| /* |
| * The constants ROM_TEXT_ADRS, ROM_SIZE, RAM_HIGH_ADRS, and RAM_LOW_ADRS |
| * are defined in config.h and Makefile. |
| * All definitions for these constants must be identical. |
| */ |
| #define ROM_BASE_ADRS 0xfff00000 /* base address of ROM */ |
| #define ROM_TEXT_ADRS (ROM_BASE_ADRS+0x0100) /* with PC & SP */ |
| #define ROM_WARM_ADRS (ROM_TEXT_ADRS+0x0004) /* warm reboot entry */ |
| #define ROM_SIZE 0x00080000 /* 512KB ROM space */ |
| #define RAM_LOW_ADRS 0x00010000 /* RAM address for vxWorks */ |
| #define RAM_HIGH_ADRS 0x00c00000 /* RAM address for bootrom */ |
| |
| /* |
| * NVRAM configuration |
| * NVRAM is implemented via the SGS Thomson M48T59Y |
| * 64Kbit (8Kbx8) Timekeeper SRAM. |
| * This 8KB NVRAM also has a TOD. See m48t59y.{h,c} for more information. |
| */ |
| |
| #define NV_RAM_ADRS TOD_NVRAM_BASE |
| #define NV_RAM_INTRVL 1 |
| #define NV_RAM_WR_ENBL SYS_TOD_UNPROTECT() |
| #define NV_RAM_WR_DSBL SYS_TOD_PROTECT() |
| |
| #define NV_OFF_BOOT0 0x0000 /* Boot string 0 (256b) */ |
| #define NV_OFF_BOOT1 0x0100 /* Boot string 1 (256b) */ |
| #define NV_OFF_BOOT2 0x0200 /* Boot string 2 (256b)*/ |
| #define NV_OFF_MACADDR 0x0400 /* 21143 MAC address (6b) */ |
| #define NV_OFF_ACTIVEBOOT 0x0406 /* Active boot string, 0 to 2 (1b) */ |
| #define NV_OFF_UNUSED1 0x0407 /* Unused (1b) */ |
| #define NV_OFF_BINDFIX 0x0408 /* See sysLib.c:sysBindFix() (1b) */ |
| #define NV_OFF_UNUSED2 0x0409 /* Unused (7b) */ |
| #define NV_OFF_TIMEZONE 0x0410 /* TIMEZONE env var (64b) */ |
| #define NV_OFF_VXWORKS_END 0x07FF /* 2047 VxWorks Total */ |
| #define NV_OFF_U_BOOT 0x0800 /* 2048 U-Boot boot-loader */ |
| #define NV_OFF_U_BOOT_ADDR (TOD_BASE + NV_OFF_U_BOOT) /* sysaddr*/ |
| #define NV_U_BOOT_ENV_SIZE 2048 /* 2K - U-Boot Total */ |
| #define NV_OFF__next_free (NV_U_BOOT_ENVSIZE +1) |
| #define NV_RAM_SIZE 8176 /* NVRAM End */ |
| |
| #endif /* __MOUSSE_H */ |