blob: 5f1252f5d8cfacb3a05f39065cd5f4b16669b21f [file] [log] [blame]
/*
* Copyright (C) 2017, Bin Meng <bmeng.cn@gmail.com>
*
* SPDX-License-Identifier: GPL-2.0+
*
* From coreboot src/soc/intel/braswell/include/soc/gpio.h
*/
#ifndef _BRASWELL_GPIO_H_
#define _BRASWELL_GPIO_H_
#include <asm/arch/iomap.h>
enum mode_list {
M0,
M1,
M2,
M3,
M4,
M5,
M6,
M7,
M8,
M9,
M10,
M11,
M12,
M13,
};
enum int_select {
L0,
L1,
L2,
L3,
L4,
L5,
L6,
L7,
L8,
L9,
L10,
L11,
L12,
L13,
L14,
L15,
};
enum gpio_en {
NATIVE = 0xff,
GPIO = 0, /* Native, no need to set PAD_VALUE */
GPO = 1, /* GPO, output only in PAD_VALUE */
GPI = 2, /* GPI, input only in PAD_VALUE */
HI_Z = 3,
NA_GPO = 0,
};
enum gpio_state {
LOW,
HIGH,
};
enum en_dis {
DISABLE, /* Disable */
ENABLE, /* Enable */
};
enum int_type {
INT_DIS,
TRIG_EDGE_LOW,
TRIG_EDGE_HIGH,
TRIG_EDGE_BOTH,
TRIG_LEVEL,
};
enum mask {
MASKABLE,
NON_MASKABLE,
};
enum glitch_cfg {
GLITCH_DISABLE,
EN_EDGE_DETECT,
EN_RX_DATA,
EN_EDGE_RX_DATA,
};
enum inv_rx_tx {
NO_INVERSION = 0,
INV_RX_ENABLE = 1,
INV_TX_ENABLE = 2,
INV_RX_TX_ENABLE = 3,
INV_RX_DATA = 4,
INV_TX_DATA = 8,
};
enum voltage {
VOLT_3_3, /* Working on 3.3 Volts */
VOLT_1_8, /* Working on 1.8 Volts */
};
enum hs_mode {
DISABLE_HS, /* Disable high speed mode */
ENABLE_HS, /* Enable high speed mode */
};
enum odt_up_dn {
PULL_UP, /* On Die Termination Up */
PULL_DOWN, /* On Die Termination Down */
};
enum odt_en {
DISABLE_OD, /* On Die Termination Disable */
ENABLE_OD, /* On Die Termination Enable */
};
enum pull_type {
P_NONE = 0, /* Pull None */
P_20K_L = 1, /* Pull Down 20K */
P_5K_L = 2, /* Pull Down 5K */
P_1K_L = 4, /* Pull Down 1K */
P_20K_H = 9, /* Pull Up 20K */
P_5K_H = 10, /* Pull Up 5K */
P_1K_H = 12 /* Pull Up 1K */
};
enum bit {
ONE_BIT = 1,
TWO_BIT = 3,
THREE_BIT = 7,
FOUR_BIT = 15,
FIVE_BIT = 31,
SIX_BIT = 63,
SEVEN_BIT = 127,
EIGHT_BIT = 255
};
enum gpe_config {
GPE,
SMI,
SCI,
};
enum community {
SOUTHWEST = 0x0000,
NORTH = 0x8000,
EAST = 0x10000,
SOUTHEAST = 0x18000,
VIRTUAL = 0x20000,
};
#define NA 0xff
#define TERMINATOR 0xffffffff
#define GPIO_FAMILY_CONF(family_name, park_mode, hysctl, vp18_mode, hs_mode, \
odt_up_dn, odt_en, curr_src_str, rcomp, family_no, community_offset) { \
.confg = ((((park_mode) != NA) ? park_mode << 26 : 0) | \
(((hysctl) != NA) ? hysctl << 24 : 0) | \
(((vp18_mode) != NA) ? vp18_mode << 21 : 0) | \
(((hs_mode) != NA) ? hs_mode << 19 : 0) | \
(((odt_up_dn) != NA) ? odt_up_dn << 18 : 0) | \
(((odt_en) != NA) ? odt_en << 17 : 0) | \
(curr_src_str)), \
.confg_changes = ((((park_mode) != NA) ? ONE_BIT << 26 : 0) | \
(((hysctl) != NA) ? TWO_BIT << 24 : 0) | \
(((vp18_mode) != NA) ? ONE_BIT << 21 : 0) | \
(((hs_mode) != NA) ? ONE_BIT << 19 : 0) | \
(((odt_up_dn) != NA) ? ONE_BIT << 18 : 0) | \
(((odt_en) != NA) ? ONE_BIT << 17 : 0) | \
(THREE_BIT)), \
.misc = ((rcomp == ENABLE) ? 1 : 0) , \
.mmio_addr = (community_offset == TERMINATOR) ? TERMINATOR : \
((family_no != NA) ? (IO_BASE_ADDRESS + community_offset +\
(0x80 * family_no) + 0x1080) : 0) , \
.name = 0 \
}
#define GPIO_PAD_CONF(pad_name, mode_select, mode, gpio_config, gpio_state, \
gpio_light_mode, int_type, int_sel, term, open_drain, current_source,\
int_mask, glitch, inv_rx_tx, wake_mask, wake_mask_bit, gpe, \
mmio_offset, community_offset) { \
.confg0 = ((((int_sel) != NA) ? (int_sel << 28) : 0) | \
(((glitch) != NA) ? (glitch << 26) : 0) | \
(((term) != NA) ? (term << 20) : 0) | \
(((mode_select) == GPIO) ? ((mode << 16) | (1 << 15)) : \
((mode << 16))) | \
(((gpio_config) != NA) ? (gpio_config << 8) : 0) | \
(((gpio_light_mode) != NA) ? (gpio_light_mode << 7) : 0) | \
(((gpio_state) == HIGH) ? 2 : 0)), \
.confg0_changes = ((((int_sel) != NA) ? (FOUR_BIT << 28) : 0) | \
(((glitch) != NA) ? (TWO_BIT << 26) : 0) | \
(((term) != NA) ? (FOUR_BIT << 20) : 0) | \
(FIVE_BIT << 15) | \
(((gpio_config) != NA) ? (THREE_BIT << 8) : 0) | \
(((gpio_light_mode) != NA) ? (ONE_BIT << 7) : 0) | \
(((gpio_state) != NA) ? ONE_BIT << 1 : 0)), \
.confg1 = ((((current_source) != NA) ? (current_source << 27) : 0) | \
(((inv_rx_tx) != NA) ? inv_rx_tx << 4 : 0) | \
(((open_drain) != NA) ? open_drain << 3 : 0) | \
(((int_type) != NA) ? int_type : 0)), \
.confg1_changes = ((((current_source) != NA) ? (ONE_BIT << 27) : 0) | \
(((inv_rx_tx) != NA) ? FOUR_BIT << 4 : 0) | \
(((open_drain) != NA) ? ONE_BIT << 3 : 0) | \
(((int_type) != NA) ? THREE_BIT : 0)), \
.community = community_offset, \
.mmio_addr = (community_offset == TERMINATOR) ? TERMINATOR : \
((mmio_offset != NA) ? (IO_BASE_ADDRESS + \
community_offset + mmio_offset) : 0), \
.name = 0, \
.misc = ((((gpe) != NA) ? (gpe << 0) : 0) | \
(((wake_mask) != NA) ? (wake_mask << 2) : 0) | \
(((int_mask) != NA) ? (int_mask << 3) : 0)) | \
(((wake_mask_bit) != NA) ? (wake_mask_bit << 4) : (NA << 4)) \
}
#endif /* _BRASWELL_GPIO_H_ */