| /* |
| * Copyright 2008-2012 Freescale Semiconductor, Inc. |
| * Kumar Gala <kumar.gala@freescale.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <asm-offsets.h> |
| #include <config.h> |
| #include <mpc85xx.h> |
| |
| #include <ppc_asm.tmpl> |
| #include <ppc_defs.h> |
| |
| #include <asm/cache.h> |
| #include <asm/mmu.h> |
| |
| /* To boot secondary cpus, we need a place for them to start up. |
| * Normally, they start at 0xfffffffc, but that's usually the |
| * firmware, and we don't want to have to run the firmware again. |
| * Instead, the primary cpu will set the BPTR to point here to |
| * this page. We then set up the core, and head to |
| * start_secondary. Note that this means that the code below |
| * must never exceed 1023 instructions (the branch at the end |
| * would then be the 1024th). |
| */ |
| .globl __secondary_start_page |
| .align 12 |
| __secondary_start_page: |
| /* First do some preliminary setup */ |
| lis r3, HID0_EMCP@h /* enable machine check */ |
| #ifndef CONFIG_E500MC |
| ori r3,r3,HID0_TBEN@l /* enable Timebase */ |
| #endif |
| #ifdef CONFIG_PHYS_64BIT |
| ori r3,r3,HID0_ENMAS7@l /* enable MAS7 updates */ |
| #endif |
| mtspr SPRN_HID0,r3 |
| |
| #ifndef CONFIG_E500MC |
| li r3,(HID1_ASTME|HID1_ABE)@l /* Addr streaming & broadcast */ |
| mfspr r0,PVR |
| andi. r0,r0,0xff |
| cmpwi r0,0x50@l /* if we are rev 5.0 or greater set MBDD */ |
| blt 1f |
| /* Set MBDD bit also */ |
| ori r3, r3, HID1_MBDD@l |
| 1: |
| mtspr SPRN_HID1,r3 |
| #endif |
| |
| #ifdef CONFIG_SYS_FSL_ERRATUM_CPU_A003999 |
| mfspr r3,SPRN_HDBCR1 |
| oris r3,r3,0x0100 |
| mtspr SPRN_HDBCR1,r3 |
| #endif |
| |
| #ifdef CONFIG_SYS_FSL_ERRATUM_A004510 |
| mfspr r3,SPRN_SVR |
| rlwinm r3,r3,0,0xff |
| li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV |
| cmpw r3,r4 |
| beq 1f |
| |
| #ifdef CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 |
| li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 |
| cmpw r3,r4 |
| beq 1f |
| #endif |
| |
| /* Not a supported revision affected by erratum */ |
| b 2f |
| |
| 1: /* Erratum says set bits 55:60 to 001001 */ |
| msync |
| isync |
| mfspr r3,SPRN_HDBCR0 |
| li r4,0x48 |
| rlwimi r3,r4,0,0x1f8 |
| mtspr SPRN_HDBCR0,r3 |
| isync |
| 2: |
| #endif |
| |
| /* Enable branch prediction */ |
| lis r3,BUCSR_ENABLE@h |
| ori r3,r3,BUCSR_ENABLE@l |
| mtspr SPRN_BUCSR,r3 |
| |
| /* Ensure TB is 0 */ |
| li r3,0 |
| mttbl r3 |
| mttbu r3 |
| |
| /* Enable/invalidate the I-Cache */ |
| lis r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@h |
| ori r2,r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@l |
| mtspr SPRN_L1CSR1,r2 |
| 1: |
| mfspr r3,SPRN_L1CSR1 |
| and. r1,r3,r2 |
| bne 1b |
| |
| lis r3,(L1CSR1_CPE|L1CSR1_ICE)@h |
| ori r3,r3,(L1CSR1_CPE|L1CSR1_ICE)@l |
| mtspr SPRN_L1CSR1,r3 |
| isync |
| 2: |
| mfspr r3,SPRN_L1CSR1 |
| andi. r1,r3,L1CSR1_ICE@l |
| beq 2b |
| |
| /* Enable/invalidate the D-Cache */ |
| lis r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@h |
| ori r2,r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@l |
| mtspr SPRN_L1CSR0,r2 |
| 1: |
| mfspr r3,SPRN_L1CSR0 |
| and. r1,r3,r2 |
| bne 1b |
| |
| lis r3,(L1CSR0_CPE|L1CSR0_DCE)@h |
| ori r3,r3,(L1CSR0_CPE|L1CSR0_DCE)@l |
| mtspr SPRN_L1CSR0,r3 |
| isync |
| 2: |
| mfspr r3,SPRN_L1CSR0 |
| andi. r1,r3,L1CSR0_DCE@l |
| beq 2b |
| |
| #define toreset(x) (x - __secondary_start_page + 0xfffff000) |
| |
| /* get our PIR to figure out our table entry */ |
| lis r3,toreset(__spin_table_addr)@h |
| ori r3,r3,toreset(__spin_table_addr)@l |
| lwz r3,0(r3) |
| |
| mfspr r0,SPRN_PIR |
| #ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2 |
| /* |
| * PIR definition for Chassis 2 |
| * 0-17 Reserved (logic 0s) |
| * 18-19 CHIP_ID, 2'b00 - SoC 1 |
| * all others - reserved |
| * 20-24 CLUSTER_ID 5'b00000 - CCM 1 |
| * all others - reserved |
| * 25-26 CORE_CLUSTER_ID 2'b00 - cluster 1 |
| * 2'b01 - cluster 2 |
| * 2'b10 - cluster 3 |
| * 2'b11 - cluster 4 |
| * 27-28 CORE_ID 2'b00 - core 0 |
| * 2'b01 - core 1 |
| * 2'b10 - core 2 |
| * 2'b11 - core 3 |
| * 29-31 THREAD_ID 3'b000 - thread 0 |
| * 3'b001 - thread 1 |
| * |
| * Power-on PIR increments threads by 0x01, cores within a cluster by 0x08 |
| * and clusters by 0x20. |
| * |
| * We renumber PIR so that all threads in the system are consecutive. |
| */ |
| |
| rlwinm r8,r0,29,0x03 /* r8 = core within cluster */ |
| srwi r10,r0,5 /* r10 = cluster */ |
| |
| mulli r5,r10,CONFIG_SYS_FSL_CORES_PER_CLUSTER |
| add r5,r5,r8 /* for spin table index */ |
| mulli r4,r5,CONFIG_SYS_FSL_THREADS_PER_CORE /* for PIR */ |
| #elif defined(CONFIG_E500MC) |
| rlwinm r4,r0,27,27,31 |
| mr r5,r4 |
| #else |
| mr r4,r0 |
| mr r5,r4 |
| #endif |
| |
| /* |
| * r10 has the base address for the entry. |
| * we cannot access it yet before setting up a new TLB |
| */ |
| slwi r8,r5,6 /* spin table is padded to 64 byte */ |
| add r10,r3,r8 |
| |
| mtspr SPRN_PIR,r4 /* write to PIR register */ |
| |
| #ifdef CONFIG_SYS_FSL_ERRATUM_A007907 |
| mfspr r8, L1CSR2 |
| clrrwi r8, r8, 10 /* clear bit [54-63] DCSTASHID */ |
| mtspr L1CSR2, r8 |
| #else |
| #ifdef CONFIG_SYS_CACHE_STASHING |
| /* set stash id to (coreID) * 2 + 32 + L1 CT (0) */ |
| slwi r8,r4,1 |
| addi r8,r8,32 |
| mtspr L1CSR2,r8 |
| #endif |
| #endif /* CONFIG_SYS_FSL_ERRATUM_A007907 */ |
| |
| #if defined(CONFIG_SYS_P4080_ERRATUM_CPU22) || \ |
| defined(CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011) |
| /* |
| * CPU22 applies to P4080 rev 1.0, 2.0, fixed in 3.0 |
| * NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in 3.0 |
| * also appleis to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1 |
| */ |
| mfspr r3,SPRN_SVR |
| rlwinm r6,r3,24,~0x800 /* clear E bit */ |
| |
| lis r5,SVR_P4080@h |
| ori r5,r5,SVR_P4080@l |
| cmpw r6,r5 |
| bne 1f |
| |
| rlwinm r3,r3,0,0xf0 |
| li r5,0x30 |
| cmpw r3,r5 |
| bge 2f |
| 1: |
| #ifdef CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011 |
| lis r3,toreset(enable_cpu_a011_workaround)@ha |
| lwz r3,toreset(enable_cpu_a011_workaround)@l(r3) |
| cmpwi r3,0 |
| beq 2f |
| #endif |
| mfspr r3,L1CSR2 |
| oris r3,r3,(L1CSR2_DCWS)@h |
| mtspr L1CSR2,r3 |
| 2: |
| #endif |
| |
| #ifdef CONFIG_SYS_FSL_ERRATUM_A005812 |
| /* |
| * A-005812 workaround sets bit 32 of SPR 976 for SoCs running in |
| * write shadow mode. This code should run after other code setting |
| * DCWS. |
| */ |
| mfspr r3,L1CSR2 |
| andis. r3,r3,(L1CSR2_DCWS)@h |
| beq 1f |
| mfspr r3, SPRN_HDBCR0 |
| oris r3, r3, 0x8000 |
| mtspr SPRN_HDBCR0, r3 |
| 1: |
| #endif |
| |
| #ifdef CONFIG_BACKSIDE_L2_CACHE |
| /* skip L2 setup on P2040/P2040E as they have no L2 */ |
| mfspr r3,SPRN_SVR |
| rlwinm r6,r3,24,~0x800 /* clear E bit of SVR */ |
| |
| lis r3,SVR_P2040@h |
| ori r3,r3,SVR_P2040@l |
| cmpw r6,r3 |
| beq 3f |
| |
| /* Enable/invalidate the L2 cache */ |
| msync |
| lis r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@h |
| ori r2,r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@l |
| mtspr SPRN_L2CSR0,r2 |
| 1: |
| mfspr r3,SPRN_L2CSR0 |
| and. r1,r3,r2 |
| bne 1b |
| |
| #ifdef CONFIG_SYS_CACHE_STASHING |
| /* set stash id to (coreID) * 2 + 32 + L2 (1) */ |
| addi r3,r8,1 |
| mtspr SPRN_L2CSR1,r3 |
| #endif |
| |
| lis r3,CONFIG_SYS_INIT_L2CSR0@h |
| ori r3,r3,CONFIG_SYS_INIT_L2CSR0@l |
| mtspr SPRN_L2CSR0,r3 |
| isync |
| 2: |
| mfspr r3,SPRN_L2CSR0 |
| andis. r1,r3,L2CSR0_L2E@h |
| beq 2b |
| #endif |
| 3: |
| /* setup mapping for the spin table, WIMGE=0b00100 */ |
| lis r13,toreset(__spin_table_addr)@h |
| ori r13,r13,toreset(__spin_table_addr)@l |
| lwz r13,0(r13) |
| /* mask by 4K */ |
| rlwinm r13,r13,0,0,19 |
| |
| lis r11,(MAS0_TLBSEL(1)|MAS0_ESEL(1))@h |
| mtspr SPRN_MAS0,r11 |
| lis r11,(MAS1_VALID|MAS1_IPROT)@h |
| ori r11,r11,(MAS1_TS|MAS1_TSIZE(BOOKE_PAGESZ_4K))@l |
| mtspr SPRN_MAS1,r11 |
| oris r11,r13,(MAS2_M|MAS2_G)@h |
| ori r11,r13,(MAS2_M|MAS2_G)@l |
| mtspr SPRN_MAS2,r11 |
| oris r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@h |
| ori r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@l |
| mtspr SPRN_MAS3,r11 |
| li r11,0 |
| mtspr SPRN_MAS7,r11 |
| tlbwe |
| |
| /* |
| * __bootpg_addr has the address of __second_half_boot_page |
| * jump there in AS=1 space with cache enabled |
| */ |
| lis r13,toreset(__bootpg_addr)@h |
| ori r13,r13,toreset(__bootpg_addr)@l |
| lwz r11,0(r13) |
| mtspr SPRN_SRR0,r11 |
| mfmsr r13 |
| ori r12,r13,MSR_IS|MSR_DS@l |
| mtspr SPRN_SRR1,r12 |
| rfi |
| |
| /* |
| * Allocate some space for the SDRAM address of the bootpg. |
| * This variable has to be in the boot page so that it can |
| * be accessed by secondary cores when they come out of reset. |
| */ |
| .align L1_CACHE_SHIFT |
| .globl __bootpg_addr |
| __bootpg_addr: |
| .long 0 |
| |
| .global __spin_table_addr |
| __spin_table_addr: |
| .long 0 |
| |
| /* |
| * This variable is set by cpu_init_r() after parsing hwconfig |
| * to enable workaround for erratum NMG_CPU_A011. |
| */ |
| .align L1_CACHE_SHIFT |
| .global enable_cpu_a011_workaround |
| enable_cpu_a011_workaround: |
| .long 1 |
| |
| /* Fill in the empty space. The actual reset vector is |
| * the last word of the page */ |
| __secondary_start_code_end: |
| .space 4092 - (__secondary_start_code_end - __secondary_start_page) |
| __secondary_reset_vector: |
| b __secondary_start_page |
| |
| |
| /* this is a separated page for the spin table and cacheable boot code */ |
| .align L1_CACHE_SHIFT |
| .global __second_half_boot_page |
| __second_half_boot_page: |
| #ifdef CONFIG_PPC_SPINTABLE_COMPATIBLE |
| lis r3,(spin_table_compat - __second_half_boot_page)@h |
| ori r3,r3,(spin_table_compat - __second_half_boot_page)@l |
| add r3,r3,r11 /* r11 has the address of __second_half_boot_page */ |
| lwz r14,0(r3) |
| #endif |
| |
| #define ENTRY_ADDR_UPPER 0 |
| #define ENTRY_ADDR_LOWER 4 |
| #define ENTRY_R3_UPPER 8 |
| #define ENTRY_R3_LOWER 12 |
| #define ENTRY_RESV 16 |
| #define ENTRY_PIR 20 |
| #define ENTRY_SIZE 64 |
| /* |
| * setup the entry |
| * r10 has the base address of the spin table. |
| * spin table is defined as |
| * struct { |
| * uint64_t entry_addr; |
| * uint64_t r3; |
| * uint32_t rsvd1; |
| * uint32_t pir; |
| * }; |
| * we pad this struct to 64 bytes so each entry is in its own cacheline |
| */ |
| li r3,0 |
| li r8,1 |
| mfspr r4,SPRN_PIR |
| stw r3,ENTRY_ADDR_UPPER(r10) |
| stw r3,ENTRY_R3_UPPER(r10) |
| stw r4,ENTRY_R3_LOWER(r10) |
| stw r3,ENTRY_RESV(r10) |
| stw r4,ENTRY_PIR(r10) |
| msync |
| stw r8,ENTRY_ADDR_LOWER(r10) |
| |
| /* spin waiting for addr */ |
| 3: |
| /* |
| * To comply with ePAPR 1.1, the spin table has been moved to cache-enabled |
| * memory. Old OS may not work with this change. A patch is waiting to be |
| * accepted for Linux kernel. Other OS needs similar fix to spin table. |
| * For OSes with old spin table code, we can enable this temporary fix by |
| * setting environmental variable "spin_table_compat". For new OSes, set |
| * "spin_table_compat=no". After Linux is fixed, we can remove this macro |
| * and related code. For now, it is enabled by default. |
| */ |
| #ifdef CONFIG_PPC_SPINTABLE_COMPATIBLE |
| cmpwi r14,0 |
| beq 4f |
| dcbf 0, r10 |
| sync |
| 4: |
| #endif |
| lwz r4,ENTRY_ADDR_LOWER(r10) |
| andi. r11,r4,1 |
| bne 3b |
| isync |
| |
| /* get the upper bits of the addr */ |
| lwz r11,ENTRY_ADDR_UPPER(r10) |
| |
| /* setup branch addr */ |
| mtspr SPRN_SRR0,r4 |
| |
| /* mark the entry as released */ |
| li r8,3 |
| stw r8,ENTRY_ADDR_LOWER(r10) |
| |
| /* mask by ~64M to setup our tlb we will jump to */ |
| rlwinm r12,r4,0,0,5 |
| |
| /* |
| * setup r3, r4, r5, r6, r7, r8, r9 |
| * r3 contains the value to put in the r3 register at secondary cpu |
| * entry. The high 32-bits are ignored on 32-bit chip implementations. |
| * 64-bit chip implementations however shall load all 64-bits |
| */ |
| #ifdef CONFIG_SYS_PPC64 |
| ld r3,ENTRY_R3_UPPER(r10) |
| #else |
| lwz r3,ENTRY_R3_LOWER(r10) |
| #endif |
| li r4,0 |
| li r5,0 |
| li r6,0 |
| lis r7,(64*1024*1024)@h |
| li r8,0 |
| li r9,0 |
| |
| /* load up the pir */ |
| lwz r0,ENTRY_PIR(r10) |
| mtspr SPRN_PIR,r0 |
| mfspr r0,SPRN_PIR |
| stw r0,ENTRY_PIR(r10) |
| |
| mtspr IVPR,r12 |
| /* |
| * Coming here, we know the cpu has one TLB mapping in TLB1[0] |
| * which maps 0xfffff000-0xffffffff one-to-one. We set up a |
| * second mapping that maps addr 1:1 for 64M, and then we jump to |
| * addr |
| */ |
| lis r10,(MAS0_TLBSEL(1)|MAS0_ESEL(0))@h |
| mtspr SPRN_MAS0,r10 |
| lis r10,(MAS1_VALID|MAS1_IPROT)@h |
| ori r10,r10,(MAS1_TSIZE(BOOKE_PAGESZ_64M))@l |
| mtspr SPRN_MAS1,r10 |
| /* WIMGE = 0b00000 for now */ |
| mtspr SPRN_MAS2,r12 |
| ori r12,r12,(MAS3_SX|MAS3_SW|MAS3_SR) |
| mtspr SPRN_MAS3,r12 |
| #ifdef CONFIG_ENABLE_36BIT_PHYS |
| mtspr SPRN_MAS7,r11 |
| #endif |
| tlbwe |
| |
| /* Now we have another mapping for this page, so we jump to that |
| * mapping |
| */ |
| mtspr SPRN_SRR1,r13 |
| rfi |
| |
| |
| .align 6 |
| .globl __spin_table |
| __spin_table: |
| .space CONFIG_MAX_CPUS*ENTRY_SIZE |
| |
| #ifdef CONFIG_PPC_SPINTABLE_COMPATIBLE |
| .align L1_CACHE_SHIFT |
| .global spin_table_compat |
| spin_table_compat: |
| .long 1 |
| |
| #endif |
| |
| __spin_table_end: |
| .space 4096 - (__spin_table_end - __spin_table) |