blob: 5e0bbe36f5bcd9d2ed1e57ecc6ca8d5914905ae2 [file] [log] [blame]
/******************************************************************************
* A collection of structures, addresses, and values associated with
* the Motorola 850T AdderIIF board. Copied from the FADS stuff.
* Magnus Damm added defines for 8xxrom and extended bd_info.
* Helmut Buchsbaum added bitvalues for BCSRx
*
* Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
*******************************************************************************
* 2003-JUL: The AdderII is using the following physical memorymap:
*******************************************************************************
* FA200000 -> FA20FFFF : IMAP internal in the cpu
* FE000000 -> FE400000 : flash connected to CS0, setup by 8xxrom
* 00000000 -> 00800000 : sdram setup by 8xxrom
*******************************************************************************/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <mpc8xx_irq.h>
#define CONFIG_MPC860 1
#define CONFIG_MPC860T 1
#define CONFIG_ADDERII 1
/* CPU Clock speed */
#define MPC8XX_FACT 12 /* Multilpy by 12 */
#define MPC8XX_XIN 4000000 /* 4MHz */
#define MPC8XX_HZ ( MPC8XX_FACT * MPC8XX_XIN )
#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ
#define CONFIG_SDRAM_50MHZ 1
/* Default Serial Console, baudrate */
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#define CONFIG_BAUDRATE 38400
#define CONFIG_LOADS_ECHO 1
/* FEC Ethernet controller configurations */
#define CONFIG_FEC_ETH 1
#define CONFIG_NET_MULTI 1
#define FEC_ENET 1
/* Interrupt level assignments.
*/
#define FEC_INTERRUPT SIU_LEVEL3 /* FEC interrupt */
/* Older kernels need clock in MHz newer in Hz */
#define CONFIG_CLOCKS_IN_MHZ 1
/* Monitor Functions */
#define CONFIG_COMMANDS ( CFG_CMD_ENV | \
CFG_CMD_FLASH | \
CFG_CMD_MEMORY| \
CFG_CMD_NET | \
CFG_CMD_PING | \
CFG_CMD_SDRAM )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/* Configuration Settings */
#define CFG_PROMPT "=>" /* Monitor Command Prompt */
#if ( CONFIG_COMMANDS & CFG_CMD_KGDB )
#define CFG_CBSIZE 1024 /* Console I/P buffer size */
#else
#define CFG_CBSIZE 256
#endif
#define CFG_PBSIZE ( CFG_CBSIZE + sizeof( CFG_PROMPT ) + 16 )
/* Print buffer size */
#define CFG_MAXARGS 16 /* Max number of cmd args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot args buffer size */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CFG_MEMTEST_START 0x00100000 /* Mem test works on */
#define CFG_MEMTEST_END 0x00800000 /* 1 ... 8MB in SDRAM */
#define CFG_LOAD_ADDR 0x00100000
#define CFG_HZ 1000
/******************************************************************************
** Low level configuration settings.
** ( adderss mappings, register init values, etc. )
** You should know what you are doing if you make changes here.
******************************************************************************/
/* Start address for the final memory configuration set up by startup code
** Please note that CFG_SDRAM_BASE must start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFE000000
#define CFG_FLASH_SIZE (( uint ) ( 4 * 1024 * 1024 )) /* 4MB */
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#define CFG_MONITOR_LEN ( 256 << 10 ) /* 256 KByte */
#define CFG_MALLOC_LEN ( 384 << 10 ) /* 384 KByte SDRAM rsvd */
/* malloc() usage */
/**
** For booting Linux, the board info and command line data
** have to be in the first 8 MB of memory, since this is
** the maximum mapped by the Linux kernel during initialization.
**/
#define CFG_BOOTMAPSZ ( 8 << 20 ) /* Initial Memory map for Linux */
/******************************************************************************
** Flash Organization
******************************************************************************/
#define CFG_MAX_FLASH_BANKS 1 /* Max no of flash mem banks */
#define CFG_MAX_FLASH_SECT 71 /* Max no of sec on 1 chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Erase flash timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Write flash timeout (ms) */
/******************************************************************************
** U-BOOT Environment variables in Flash
******************************************************************************/
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_OFFSET 0x00040000
#define CFG_ENV_SIZE 0x10000 /* 64KBytes env space */
#define CFG_ENV_SECT_SIZE 0x10000
/******************************************************************************
** Cache Configuration
******************************************************************************/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if ( CONFIG_COMMANDS & CFG_CMD_KGDB )
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/******************************************************************************
** Internal memory mapped register
******************************************************************************/
#define CFG_IMMR 0xFA200000
#define CFG_IMMR_SIZE (( uint) ( 62 * 1024 )) /* 64 KByte res */
/* Definitions for initial stack pointer and data area ( in DPRAM ) */
#define CFG_INIT_RAM_ADDR CFG_IMMR
#define CFG_INIT_RAM_END 0x2F00 /* end of used area in DPRAM */
#define CFG_GBL_DATA_SIZE 64
#define CFG_GBL_DATA_OFFSET ( CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE )
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/* SIU Module Configuration Register */
#define CFG_SIUMCR ( SIUMCR_AEME | SIUMCR_MLRC01 | SIUMCR_DBGC10 )
/******************************************************************************
** SYPCR - System protection and control
** SYPCR - can be written only once after reset
******************************************************************************/
#if defined( CONFIG_WATCHDOG )
#define CFG_SYPCR ( SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | \
SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | \
SYPCR_SWP )
#else
#define CFG_SYPCR ( SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | \
SYPCR_SWF | SYPCR_SWP )
#endif
/* TBSCR - Time Base Status and Control Register */
#define CFG_TBSCR ( TBSCR_REFA | TBSCR_REFB | TBSCR_TBE )
/* PISCR - Periodic Interrupt Status and Control */
#define CFG_PISCR ( PISCR_PS | PISCR_PITF )
/* PLPRCR - PLL, Low-Power, and Reset Control Register */
#define CFG_PLPRCR ((( MPC8XX_FACT - 1 ) << PLPRCR_MF_SHIFT ) | \
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST )
/* SCCR - System Clock and reset Control Register */
#define SCCR_MASK SCCR_EBDF11
#define CFG_SCCR ( SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
SCCR_DFBRG00 | SCCR_DFNL000| SCCR_DFNH000 | \
SCCR_DFLCD000 | SCCR_DFALCD00 )
#define CFG_DER 0
/******************************************************************************
** Because of the way the 860 starts up and assigns CS0 the
** entire address space, we have to set the memory controller
** differently. Normally, you write the option register
** first, and then enable the chip select by writing the
** base register. For CS0, you must write the base register
** first, followed by the option register.
******************************************************************************/
/**
** Memory Controller Definitions
** BR0/1/2... and OR0/1/2...
*/
/* For AdderII BR0 FLASH */
#define CFG_REMAP_OR_AM 0xFF800000 /* OR addr mask */
#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */
/* Flash Timings: ACS = 11, TRLX = 1, CSNT = 0, SCY = 7 */
#define CFG_OR_TIMING_FLASH ( OR_ACS_DIV2 | OR_BI | OR_SCY_7_CLK | OR_TRLX )
#define CFG_OR0_REMAP ( CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH )
#define CFG_OR0_PRELIM CFG_OR0_REMAP
#define CFG_BR0_PRELIM (( CFG_FLASH_BASE & BR_BA_MSK ) | \
BR_PS_16 | BR_V )
/* For AdderII BR1 SDRAM */
#define CFG_PRELIM_OR1_AM 0xFF800000
#define CFG_OR1_REMAP ( CFG_PRELIM_OR1_AM | OR_CSNT_SAM | OR_ACS_DIV2 )
#define CFG_OR1_PRELIM ( CFG_PRELIM_OR1_AM | OR_CSNT_SAM | OR_ACS_DIV2 )
#define CFG_BR1_PRELIM ( CFG_SDRAM_BASE | BR_MS_UPMA | BR_V )
/*******************************************************************************
* Internal Definitions Boot Flags
*******************************************************************************/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#endif
/* __CONFIG_H */