| /* |
| * (C) Copyright 2007-2008 |
| * Stelian Pop <stelian@popies.net> |
| * Lead Tech Design <www.leadtechdesign.com> |
| * |
| * Configuation settings for the AT91SAM9261EK board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* ARM asynchronous clock */ |
| #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ |
| #define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */ |
| |
| #ifdef CONFIG_AT91SAM9G10 |
| #define CONFIG_AT91SAM9G10EK /* It's an Atmel AT91SAM9G10 EK*/ |
| #else |
| #define CONFIG_AT91SAM9261EK /* It's an Atmel AT91SAM9261 EK*/ |
| #endif |
| |
| #include <asm/hardware.h> |
| |
| #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ |
| #define CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_INITRD_TAG |
| |
| #define CONFIG_SKIP_LOWLEVEL_INIT |
| |
| #define CONFIG_DISPLAY_CPUINFO |
| |
| #define CONFIG_OF_LIBFDT |
| |
| #define CONFIG_SYS_GENERIC_BOARD |
| |
| #define CONFIG_ATMEL_LEGACY |
| #define CONFIG_SYS_TEXT_BASE 0x21f00000 |
| |
| /* |
| * Hardware drivers |
| */ |
| |
| /* gpio */ |
| #define CONFIG_AT91_GPIO |
| #define CONFIG_AT91_GPIO_PULLUP 1 |
| |
| /* serial console */ |
| #define CONFIG_ATMEL_USART |
| #define CONFIG_USART_BASE ATMEL_BASE_DBGU |
| #define CONFIG_USART_ID ATMEL_ID_SYS |
| #define CONFIG_BAUDRATE 115200 |
| |
| /* LCD */ |
| #define CONFIG_LCD |
| #define LCD_BPP LCD_COLOR8 |
| #define CONFIG_LCD_LOGO |
| #undef LCD_TEST_PATTERN |
| #define CONFIG_LCD_INFO |
| #define CONFIG_LCD_INFO_BELOW_LOGO |
| #define CONFIG_SYS_WHITE_ON_BLACK |
| #define CONFIG_ATMEL_LCD |
| #ifdef CONFIG_AT91SAM9261EK |
| #define CONFIG_ATMEL_LCD_BGR555 |
| #endif |
| |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV |
| |
| /* LED */ |
| #define CONFIG_AT91_LED |
| #define CONFIG_RED_LED AT91_PIN_PA23 /* this is the power led */ |
| #define CONFIG_GREEN_LED AT91_PIN_PA13 /* this is the user1 led */ |
| #define CONFIG_YELLOW_LED AT91_PIN_PA14 /* this is the user2 led */ |
| |
| #define CONFIG_BOOTDELAY 3 |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| #undef CONFIG_CMD_BDI |
| #undef CONFIG_CMD_FPGA |
| #undef CONFIG_CMD_IMI |
| #undef CONFIG_CMD_IMLS |
| #undef CONFIG_CMD_LOADS |
| #undef CONFIG_CMD_SOURCE |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_USB |
| |
| /* SDRAM */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define CONFIG_SYS_SDRAM_BASE 0x20000000 |
| #define CONFIG_SYS_SDRAM_SIZE 0x04000000 |
| #define CONFIG_SYS_INIT_SP_ADDR \ |
| (ATMEL_BASE_SRAM + 0x1000 - GENERATED_GBL_DATA_SIZE) |
| |
| /* DataFlash */ |
| #define CONFIG_ATMEL_DATAFLASH_SPI |
| #define CONFIG_HAS_DATAFLASH |
| #define CONFIG_SYS_MAX_DATAFLASH_BANKS 2 |
| #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ |
| #define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* CS3 */ |
| #define AT91_SPI_CLK 15000000 |
| #define DATAFLASH_TCSS (0x1a << 16) |
| #define DATAFLASH_TCHS (0x1 << 24) |
| |
| /* NAND flash */ |
| #ifdef CONFIG_CMD_NAND |
| #define CONFIG_NAND_ATMEL |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE 0x40000000 |
| #define CONFIG_SYS_NAND_DBW_8 |
| /* our ALE is AD22 */ |
| #define CONFIG_SYS_NAND_MASK_ALE (1 << 22) |
| /* our CLE is AD21 */ |
| #define CONFIG_SYS_NAND_MASK_CLE (1 << 21) |
| #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 |
| #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC15 |
| |
| #endif |
| |
| /* NOR flash - no real flash on this board */ |
| #define CONFIG_SYS_NO_FLASH |
| |
| /* Ethernet */ |
| #define CONFIG_DRIVER_DM9000 |
| #define CONFIG_DM9000_BASE 0x30000000 |
| #define DM9000_IO CONFIG_DM9000_BASE |
| #define DM9000_DATA (CONFIG_DM9000_BASE + 4) |
| #define CONFIG_DM9000_USE_16BIT |
| #define CONFIG_DM9000_NO_SROM |
| #define CONFIG_NET_RETRY_COUNT 20 |
| #define CONFIG_RESET_PHY_R |
| |
| /* USB */ |
| #define CONFIG_USB_ATMEL |
| #define CONFIG_USB_ATMEL_CLK_SEL_PLLB |
| #define CONFIG_USB_OHCI_NEW |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9261_UHP_BASE */ |
| #ifdef CONFIG_AT91SAM9G10EK |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g10" |
| #else |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9261" |
| #endif |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 |
| #define CONFIG_USB_STORAGE |
| #define CONFIG_CMD_FAT |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ |
| |
| #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE |
| #define CONFIG_SYS_MEMTEST_END 0x23e00000 |
| |
| #ifdef CONFIG_SYS_USE_DATAFLASH_CS0 |
| |
| /* bootstrap + u-boot + env + linux in dataflash on CS0 */ |
| #define CONFIG_ENV_IS_IN_DATAFLASH |
| #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400) |
| #define CONFIG_ENV_OFFSET 0x4200 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + CONFIG_ENV_OFFSET) |
| #define CONFIG_ENV_SIZE 0x4200 |
| #define CONFIG_BOOTCOMMAND "cp.b 0xC0084000 0x22000000 0x210000; bootm" |
| #define CONFIG_BOOTARGS "console=ttyS0,115200 " \ |
| "root=/dev/mtdblock0 " \ |
| "mtdparts=atmel_nand:-(root) " \ |
| "rw rootfstype=jffs2" |
| |
| #elif CONFIG_SYS_USE_DATAFLASH_CS3 |
| |
| /* bootstrap + u-boot + env + linux in dataflash on CS3 */ |
| #define CONFIG_ENV_IS_IN_DATAFLASH |
| #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 + 0x8400) |
| #define CONFIG_ENV_OFFSET 0x4200 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS3 + CONFIG_ENV_OFFSET) |
| #define CONFIG_ENV_SIZE 0x4200 |
| #define CONFIG_BOOTCOMMAND "cp.b 0xD0084000 0x22000000 0x210000; bootm" |
| #define CONFIG_BOOTARGS "console=ttyS0,115200 " \ |
| "root=/dev/mtdblock0 " \ |
| "mtdparts=atmel_nand:-(root) " \ |
| "rw rootfstype=jffs2" |
| |
| #else /* CONFIG_SYS_USE_NANDFLASH */ |
| |
| /* bootstrap + u-boot + env + linux in nandflash */ |
| #define CONFIG_ENV_IS_IN_NAND |
| #define CONFIG_ENV_OFFSET 0xc0000 |
| #define CONFIG_ENV_OFFSET_REDUND 0x100000 |
| #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ |
| #define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm" |
| #define CONFIG_BOOTARGS \ |
| "console=ttyS0,115200 earlyprintk " \ |
| "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ |
| "256k(env),256k(env_redundant),256k(spare)," \ |
| "512k(dtb),6M(kernel)ro,-(rootfs) " \ |
| "root=/dev/mtdblock7 rw rootfstype=jffs2" |
| #endif |
| |
| #define CONFIG_SYS_PROMPT "U-Boot> " |
| #define CONFIG_SYS_CBSIZE 256 |
| #define CONFIG_SYS_MAXARGS 16 |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_LONGHELP |
| #define CONFIG_CMDLINE_EDITING |
| #define CONFIG_AUTO_COMPLETE |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) |
| |
| #endif |