| /* |
| * (C) Copyright 2006 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * Based on original work by |
| * Roel Loeffen, (C) Copyright 2006 Prodrive B.V. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /************************************************************************ |
| * p3mx.h - configuration for Prodrive P3M750 & P3M7448 boards |
| * |
| * The defines: |
| * CONFIG_P3M750 or |
| * CONFIG_P3M7448 |
| * are written into include/config.h by the "make xxx_config" command |
| ***********************************************************************/ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /*----------------------------------------------------------------------- |
| * High Level Configuration Options |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_P3Mx /* used for both board versions */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xfff00000 |
| |
| #if defined (CONFIG_P3M750) |
| #define CONFIG_750FX /* 750GL/GX/FX */ |
| #define CONFIG_HIGH_BATS /* High BATs supported */ |
| #define CONFIG_SYS_BOARD_NAME "P3M750" |
| #define CONFIG_SYS_BUS_CLK 100000000 |
| #define CONFIG_SYS_TCLK 100000000 |
| #elif defined (CONFIG_P3M7448) |
| #define CONFIG_74xx |
| #define CONFIG_SYS_BOARD_NAME "P3M7448" |
| #define CONFIG_SYS_BUS_CLK 133333333 |
| #define CONFIG_SYS_TCLK 133333333 |
| #endif |
| #define CONFIG_SYS_GT_DUAL_CPU /* also for JTAG even with one cpu */ |
| |
| /* which initialization functions to call for this board */ |
| #define CONFIG_SYS_BOARD_ASM_INIT 1 |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ |
| #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */ |
| |
| /*----------------------------------------------------------------------- |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #ifdef CONFIG_P3M750 |
| #define CONFIG_SYS_SDRAM1_BASE 0x10000000 /* each 256 MByte */ |
| #endif |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #if defined (CONFIG_P3M750) |
| #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of flash banks */ |
| #define CONFIG_SYS_BOOT_SIZE _8M /* boot flash */ |
| #elif defined (CONFIG_P3M7448) |
| #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of flash banks */ |
| #define CONFIG_SYS_BOOT_SIZE _16M /* boot flash */ |
| #endif |
| #define CONFIG_SYS_BOOT_SPACE CONFIG_SYS_FLASH_BASE /* BOOT_CS0 flash 0 */ |
| #define CONFIG_SYS_MONITOR_BASE 0xfff00000 |
| #define CONFIG_SYS_RESET_ADDRESS 0xfff00100 |
| #define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */ |
| #define CONFIG_SYS_MISC_REGION_BASE 0xf0000000 |
| |
| #define CONFIG_SYS_DFL_GT_REGS 0xf1000000 /* boot time GT_REGS */ |
| #define CONFIG_SYS_GT_REGS 0xf1000000 /* GT Registers are mapped here */ |
| #define CONFIG_SYS_INT_SRAM_BASE 0x42000000 /* GT offers 256k internal SRAM */ |
| |
| /*----------------------------------------------------------------------- |
| * Initial RAM & stack pointer (placed in internal SRAM) |
| *----------------------------------------------------------------------*/ |
| /* |
| * When locking data in cache you should point the CONFIG_SYS_INIT_RAM_ADDRESS |
| * To an unused memory region. The stack will remain in cache until RAM |
| * is initialized |
| */ |
| #undef CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x42000000 |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| |
| |
| /*----------------------------------------------------------------------- |
| * Serial Port |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_MPSC /* MV64460 Serial */ |
| #define CONFIG_MPSC_PORT 0 |
| #define CONFIG_BAUDRATE 115200 /* console baudrate */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /*----------------------------------------------------------------------- |
| * Ethernet |
| *----------------------------------------------------------------------*/ |
| /* Change the default ethernet port, use this define (options: 0, 1, 2) */ |
| #define CONFIG_SYS_ETH_PORT ETH_0 |
| #define MV_ETH_DEVS 2 |
| #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH related |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| #define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ |
| #if defined (CONFIG_P3M750) |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* one sector (1 device) */ |
| #elif defined (CONFIG_P3M7448) |
| #define CONFIG_ENV_SECT_SIZE 0x40000 /* two sectors (2 devices parallel */ |
| #endif |
| #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) |
| |
| /*----------------------------------------------------------------------- |
| * DDR SDRAM |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_MV64460_ECC |
| |
| /*----------------------------------------------------------------------- |
| * I2C |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed default */ |
| |
| /* I2C RTC */ |
| #define CONFIG_RTC_M41T11 1 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| #define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */ |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------*/ |
| #define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ |
| #define PCI_HOST_FORCE 1 /* configure as pci host */ |
| #define PCI_HOST_AUTO 2 /* detected via arbiter enable */ |
| |
| #undef CONFIG_PCI /* include pci support */ |
| #ifdef CONFIG_PCI |
| #define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| #define CONFIG_PCI_SCAN_SHOW /* show devices on bus */ |
| #endif /* CONFIG_PCI */ |
| |
| /* PCI MEMORY MAP section */ |
| #define CONFIG_SYS_PCI0_MEM_BASE 0x80000000 |
| #define CONFIG_SYS_PCI0_MEM_SIZE _128M |
| #define CONFIG_SYS_PCI1_MEM_BASE 0x88000000 |
| #define CONFIG_SYS_PCI1_MEM_SIZE _128M |
| |
| #define CONFIG_SYS_PCI0_0_MEM_SPACE (CONFIG_SYS_PCI0_MEM_BASE) |
| #define CONFIG_SYS_PCI1_0_MEM_SPACE (CONFIG_SYS_PCI1_MEM_BASE) |
| |
| /* PCI I/O MAP section */ |
| #define CONFIG_SYS_PCI0_IO_BASE 0xfa000000 |
| #define CONFIG_SYS_PCI0_IO_SIZE _16M |
| #define CONFIG_SYS_PCI1_IO_BASE 0xfb000000 |
| #define CONFIG_SYS_PCI1_IO_SIZE _16M |
| |
| #define CONFIG_SYS_PCI0_IO_SPACE (CONFIG_SYS_PCI0_IO_BASE) |
| #define CONFIG_SYS_PCI0_IO_SPACE_PCI 0x00000000 |
| #define CONFIG_SYS_PCI1_IO_SPACE (CONFIG_SYS_PCI1_IO_BASE) |
| #define CONFIG_SYS_PCI1_IO_SPACE_PCI 0x00000000 |
| |
| #define CONFIG_SYS_ISA_IO_BASE_ADDRESS (CONFIG_SYS_PCI0_IO_BASE) |
| #define CONFIG_SYS_PCI_IDSEL 0x30 |
| |
| #undef CONFIG_BOOTARGS |
| #define CONFIG_EXTRA_ENV_SETTINGS_COMMON \ |
| "netdev=eth0\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ |
| "flash_nfs=run nfsargs addip addtty;" \ |
| "bootm ${kernel_addr}\0" \ |
| "flash_self=run ramargs addip addtty;" \ |
| "bootm ${kernel_addr} ${ramdisk_addr}\0" \ |
| "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ |
| "bootm\0" \ |
| "rootpath=/opt/eldk/ppc_6xx\0" \ |
| "u-boot=p3mx/u-boot/u-boot.bin\0" \ |
| "load=tftp 100000 ${u-boot}\0" \ |
| "update=protect off fff00000 fff3ffff;era fff00000 fff3ffff;" \ |
| "cp.b 100000 fff00000 40000;" \ |
| "setenv filesize;saveenv\0" \ |
| "upd=run load update\0" \ |
| "serverip=11.0.0.152\0" |
| |
| #if defined (CONFIG_P3M750) |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_EXTRA_ENV_SETTINGS_COMMON \ |
| "hostname=p3m750\0" \ |
| "bootfile=/tftpboot/p3mx/vxWorks.st\0" \ |
| "kernel_addr=fc000000\0" \ |
| "ramdisk_addr=fc180000\0" \ |
| "vxfile=p3m750/vxWorks\0" \ |
| "vxuser=ddg\0" \ |
| "vxpass=ddg\0" \ |
| "vxtarget=target\0" \ |
| "vxflags=0x8\0" \ |
| "vxargs=setenv bootargs mgi(0,0)host:${vxfile} h=${serverip} " \ |
| "e=${ipaddr} u=${vxuser} pw=${vxpass} tn=${vxtarget} " \ |
| "f=${vxflags}\0" |
| #elif defined (CONFIG_P3M7448) |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_EXTRA_ENV_SETTINGS_COMMON \ |
| "hostname=p3m7448\0" |
| #endif |
| |
| #if defined (CONFIG_P3M750) |
| #define CONFIG_BOOTCOMMAND "tftp;run vxargs;bootvx" |
| #elif defined (CONFIG_P3M7448) |
| #define CONFIG_BOOTCOMMAND " " |
| #endif |
| |
| #define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DIAG |
| #define CONFIG_CMD_ELF |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_IRQ |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_REGINFO |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_SDRAM |
| |
| |
| /*----------------------------------------------------------------------- |
| * Miscellaneous configurable options |
| *----------------------------------------------------------------------*/ |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x08000000 /* default load address */ |
| |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| #define CONFIG_LOOPW 1 /* enable loopw command */ |
| #define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ |
| #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ |
| #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ |
| |
| /*----------------------------------------------------------------------- |
| * Marvell MV64460 config settings |
| *----------------------------------------------------------------------*/ |
| /* Reset values for Port behavior (8bit/ 32bit, etc.) only corrected device width */ |
| #if defined (CONFIG_P3M750) |
| #define CONFIG_SYS_BOOT_PAR 0x8FDFF87F /* 16 bit flash, disable burst*/ |
| #elif defined (CONFIG_P3M7448) |
| #define CONFIG_SYS_BOOT_PAR 0x8FEFFFFF /* 32 bit flash, burst enabled */ |
| #endif |
| |
| /* |
| * MPP[0] Serial Port 0 TxD TxD OUT Connected to P14 (buffered) |
| * MPP[1] Serial Port 0 RxD RxD IN Connected to P14 (buffered) |
| * MPP[2] NC |
| * MPP[3] Serial Port 1 TxD TxD OUT Connected to P14 (buffered) |
| * MPP[4] PCI Monarch# GPIO IN Connected to P12 |
| * MPP[5] Serial Port 1 RxD RxD IN Connected to P14 (buffered) |
| * MPP[6] PMC Carrier Interrupt 0 Int IN Connected to P14 |
| * MPP[7] PMC Carrier Interrupt 1 Int IN Connected to P14 |
| * MPP[8] Reserved Do not use |
| * MPP[9] Reserved Do not use |
| * MPP[10] Reserved Do not use |
| * MPP[11] Reserved Do not use |
| * MPP[12] Phy 0 Interrupt Int IN |
| * MPP[13] Phy 1 Interrupt Int IN |
| * MPP[14] NC |
| * MPP[15] NC |
| * MPP[16] PCI Interrupt C Int IN Connected to P11 |
| * MPP[17] PCI Interrupt D Int IN Connected to P11 |
| * MPP[18] Watchdog NMI# GPIO IN Connected to MPP[24] |
| * MPP[19] Watchdog Expired# WDE OUT Connected to rst logic |
| * MPP[20] Watchdog Status WD_STS IN Read back of rst by watchdog |
| * MPP[21] NC |
| * MPP[22] GP LED Green GPIO OUT |
| * MPP[23] GP LED Red GPIO OUT |
| * MPP[24] Watchdog NMI# Int OUT |
| * MPP[25] NC |
| * MPP[26] NC |
| * MPP[27] PCI Interrupt A Int IN Connected to P11 |
| * MPP[28] NC |
| * MPP[29] PCI Interrupt B Int IN Connected to P11 |
| * MPP[30] Module reset GPIO OUT Board reset |
| * MPP[31] PCI EReady GPIO IN Connected to P12 |
| */ |
| #define CONFIG_SYS_MPP_CONTROL_0 0x00303022 |
| #define CONFIG_SYS_MPP_CONTROL_1 0x00000000 |
| #define CONFIG_SYS_MPP_CONTROL_2 0x00004000 |
| #define CONFIG_SYS_MPP_CONTROL_3 0x00000004 |
| #define CONFIG_SYS_GPP_LEVEL_CONTROL 0x280730D0 |
| |
| /*---------------------------------------------------------------------- |
| * Initial BAT mappings |
| */ |
| |
| /* NOTES: |
| * 1) GUARDED and WRITE_THRU not allowed in IBATS |
| * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT |
| */ |
| /* SDRAM */ |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_GUARDEDSTORAGE | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| |
| /* init ram */ |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_256K | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| |
| /* PCI0, PCI1 in one BAT */ |
| #define CONFIG_SYS_IBAT2L BATL_NO_ACCESS |
| #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U |
| #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| |
| /* GT regs, bootrom, all the devices, PCI I/O */ |
| #define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW) |
| #define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M) |
| #define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| #define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM1_BASE | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U |
| |
| /* set rest out of range for Linux !!!!!!!!!!! */ |
| |
| /* IBAT5 and DBAT5 */ |
| #define CONFIG_SYS_IBAT5L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT5U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT5L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U |
| |
| /* IBAT6 and DBAT6 */ |
| #define CONFIG_SYS_IBAT6L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT6U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT6L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U |
| |
| /* IBAT7 and DBAT7 */ |
| #define CONFIG_SYS_IBAT7L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT7U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT7L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */ |
| #define CONFIG_SYS_VXWORKS_MAC_PTR 0x42010000 /* use some memory in SRAM that's not used!!! */ |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * L2CR setup -- make sure this is right for your board! |
| * look in include/mpc74xx.h for the defines used here |
| */ |
| #define CONFIG_SYS_L2 |
| |
| #if defined (CONFIG_750CX) || defined (CONFIG_750FX) |
| #define L2_INIT 0 |
| #else |
| #define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ |
| L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) |
| #endif |
| |
| #define L2_ENABLE (L2_INIT | L2CR_L2E) |
| |
| #ifndef __ASSEMBLY__ |
| #include <../board/Marvell/include/core.h> |
| #endif |
| |
| #endif /* __CONFIG_H */ |