| /* |
| * (C) Copyright 2009 |
| * Detlev Zundel, DENX Software Engineering, dzu@denx.de. |
| * |
| * (C) Copyright 2003-2005 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ |
| #define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ |
| #define CONFIG_INKA4X0 1 /* INKA4x0 board */ |
| |
| /* |
| * Valid values for CONFIG_SYS_TEXT_BASE are: |
| * 0xFFE00000 boot low |
| * 0x00100000 boot from RAM (for testing only) |
| */ |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xFFE00000 /* Standard: boot low */ |
| #endif |
| #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc5xxx/u-boot-customlayout.lds" |
| |
| #define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ |
| |
| #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ |
| |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported */ |
| |
| /* |
| * Serial console configuration |
| */ |
| #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ |
| #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } |
| |
| /* |
| * PCI Mapping: |
| * 0x40000000 - 0x4fffffff - PCI Memory |
| * 0x50000000 - 0x50ffffff - PCI IO Space |
| */ |
| #define CONFIG_PCI 1 |
| #define CONFIG_PCI_PNP 1 |
| #define CONFIG_PCI_SCAN_SHOW 1 |
| #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 |
| |
| #define CONFIG_PCI_MEM_BUS 0x40000000 |
| #define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS |
| #define CONFIG_PCI_MEM_SIZE 0x10000000 |
| |
| #define CONFIG_PCI_IO_BUS 0x50000000 |
| #define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS |
| #define CONFIG_PCI_IO_SIZE 0x01000000 |
| |
| #define CONFIG_SYS_XLB_PIPELINING 1 |
| |
| /* Partitions */ |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_ISO_PARTITION |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_IDE |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_SNTP |
| #define CONFIG_CMD_USB |
| |
| #define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ |
| |
| #if (CONFIG_SYS_TEXT_BASE == 0xFFE00000) /* Boot low */ |
| # define CONFIG_SYS_LOWBOOT 1 |
| #endif |
| |
| /* |
| * Autobooting |
| */ |
| #define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ |
| |
| #define CONFIG_PREBOOT "echo;" \ |
| "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ |
| "echo" |
| |
| #undef CONFIG_BOOTARGS |
| |
| #define CONFIG_ETHADDR 00:a0:a4:03:00:00 |
| #define CONFIG_OVERWRITE_ETHADDR_ONCE |
| |
| #define CONFIG_IPADDR 192.168.100.2 |
| #define CONFIG_SERVERIP 192.168.100.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define HOSTNAME inka4x0 |
| #define CONFIG_BOOTFILE "/tftpboot/inka4x0/uImage" |
| #define CONFIG_ROOTPATH "/opt/eldk/ppc_6xx" |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "nfsargs=setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=${serverip}:${rootpath}\0" \ |
| "ramargs=setenv bootargs root=/dev/ram rw\0" \ |
| "addip=setenv bootargs ${bootargs} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ |
| ":${hostname}:${netdev}:off panic=1\0" \ |
| "addcons=setenv bootargs ${bootargs} " \ |
| "console=ttyS0,${baudrate}\0" \ |
| "flash_nfs=run nfsargs addip addcons;" \ |
| "bootm ${kernel_addr}\0" \ |
| "net_nfs=tftp 200000 ${bootfile};" \ |
| "run nfsargs addip addcons;bootm\0" \ |
| "enable_disp=mw.l 100000 04000000 1;" \ |
| "cp.l 100000 f0000b20 1;" \ |
| "cp.l 100000 f0000b28 1\0" \ |
| "ideargs=setenv bootargs root=/dev/hda1 rw\0" \ |
| "ide_boot=ext2load ide 0:1 200000 uImage;" \ |
| "run ideargs addip addcons enable_disp;bootm\0" \ |
| "brightness=255\0" \ |
| "" |
| |
| #define CONFIG_BOOTCOMMAND "run ide_boot" |
| |
| /* |
| * IPB Bus clocking configuration. |
| */ |
| #define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ |
| |
| /* |
| * Flash configuration |
| */ |
| #define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ |
| #define CONFIG_FLASH_CFI_DRIVER 1 |
| #define CONFIG_SYS_FLASH_BASE 0xffe00000 |
| #define CONFIG_SYS_FLASH_SIZE 0x00200000 |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ |
| |
| /* |
| * Environment settings |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x2000 |
| #define CONFIG_ENV_OVERWRITE 1 |
| #define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ |
| |
| /* |
| * Memory map |
| */ |
| #define CONFIG_SYS_MBAR 0xF0000000 |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_DEFAULT_MBAR 0x80000000 |
| |
| /* |
| * SDRAM controller configuration |
| */ |
| #undef CONFIG_SDR_MT48LC16M16A2 |
| #undef CONFIG_DDR_MT46V16M16 |
| #undef CONFIG_DDR_MT46V32M16 |
| #undef CONFIG_DDR_HYB25D512160BF |
| #define CONFIG_DDR_K4H511638C |
| |
| /* Use ON-Chip SRAM until RAM will be available */ |
| #define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM |
| |
| /* preserve space for the post_word at end of on-chip SRAM */ |
| #define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4) |
| |
| #ifdef CONFIG_POST |
| #define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE |
| #else |
| #define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE |
| #endif |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| # define CONFIG_SYS_RAMBOOT 1 |
| #endif |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Ethernet configuration |
| */ |
| #define CONFIG_MPC5xxx_FEC 1 |
| #define CONFIG_MPC5xxx_FEC_MII100 |
| /* |
| * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb |
| */ |
| /* #define CONFIG_MPC5xxx_FEC_MII10 */ |
| #define CONFIG_PHY_ADDR 0x00 |
| #define CONFIG_MII |
| |
| /* |
| * GPIO configuration |
| * |
| * use CS1 as gpio_wkup_6 output |
| * Bit 0 (mask: 0x80000000): 0 |
| * use ALT CAN position: Bits 2-3 (mask: 0x30000000): |
| * 00 -> No Alternatives, I2C1 is used for onboard EEPROM |
| * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard |
| * EEPROM |
| * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 |
| * use PSC2 as UART: Bits 24-27 (mask: 0x00000070): 0100 |
| * use PSC3 as UART: Bits 20-23 (mask: 0x00000700): 0100 |
| * use PSC6 as UART: Bits 9-11 (mask: 0x00700000): 0101 |
| */ |
| #define CONFIG_SYS_GPS_PORT_CONFIG 0x01501444 |
| |
| /* |
| * RTC configuration |
| */ |
| #define CONFIG_RTC_RTC4543 1 /* use external RTC */ |
| |
| /* |
| * Software (bit-bang) three wire serial configuration |
| * |
| * Note that we need the ifdefs because otherwise compilation of |
| * mkimage.c fails. |
| */ |
| #define CONFIG_SOFT_TWS 1 |
| |
| #ifdef TWS_IMPLEMENTATION |
| #include <mpc5xxx.h> |
| #include <asm/io.h> |
| |
| #define TWS_CE MPC5XXX_GPIO_WKUP_PSC1_4 /* GPIO_WKUP_0 */ |
| #define TWS_WR MPC5XXX_GPIO_WKUP_PSC2_4 /* GPIO_WKUP_1 */ |
| #define TWS_DATA MPC5XXX_GPIO_SINT_PSC3_4 /* GPIO_SINT_0 */ |
| #define TWS_CLK MPC5XXX_GPIO_SINT_PSC3_5 /* GPIO_SINT_1 */ |
| |
| static inline void tws_ce(unsigned bit) |
| { |
| struct mpc5xxx_wu_gpio *wu_gpio = |
| (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; |
| if (bit) |
| setbits_8(&wu_gpio->dvo, TWS_CE); |
| else |
| clrbits_8(&wu_gpio->dvo, TWS_CE); |
| } |
| |
| static inline void tws_wr(unsigned bit) |
| { |
| struct mpc5xxx_wu_gpio *wu_gpio = |
| (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; |
| if (bit) |
| setbits_8(&wu_gpio->dvo, TWS_WR); |
| else |
| clrbits_8(&wu_gpio->dvo, TWS_WR); |
| } |
| |
| static inline void tws_clk(unsigned bit) |
| { |
| struct mpc5xxx_gpio *gpio = |
| (struct mpc5xxx_gpio *)MPC5XXX_GPIO; |
| if (bit) |
| setbits_8(&gpio->sint_dvo, TWS_CLK); |
| else |
| clrbits_8(&gpio->sint_dvo, TWS_CLK); |
| } |
| |
| static inline void tws_data(unsigned bit) |
| { |
| struct mpc5xxx_gpio *gpio = |
| (struct mpc5xxx_gpio *)MPC5XXX_GPIO; |
| if (bit) |
| setbits_8(&gpio->sint_dvo, TWS_DATA); |
| else |
| clrbits_8(&gpio->sint_dvo, TWS_DATA); |
| } |
| |
| static inline unsigned tws_data_read(void) |
| { |
| struct mpc5xxx_gpio *gpio = |
| (struct mpc5xxx_gpio *)MPC5XXX_GPIO; |
| return !!(in_8(&gpio->sint_ival) & TWS_DATA); |
| } |
| |
| static inline void tws_data_config_output(unsigned output) |
| { |
| struct mpc5xxx_gpio *gpio = |
| (struct mpc5xxx_gpio *)MPC5XXX_GPIO; |
| if (output) |
| setbits_8(&gpio->sint_ddr, TWS_DATA); |
| else |
| clrbits_8(&gpio->sint_ddr, TWS_DATA); |
| } |
| #endif /* TWS_IMPLEMENTATION */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| # define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ |
| #endif |
| |
| /* Enable an alternate, more extensive memory test */ |
| #define CONFIG_SYS_ALT_MEMTEST |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ |
| |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| /* |
| * Enable loopw command. |
| */ |
| #define CONFIG_LOOPW |
| |
| /* |
| * Various low-level settings |
| */ |
| #define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI |
| #define CONFIG_SYS_HID0_FINAL HID0_ICE |
| |
| #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE |
| #define CONFIG_SYS_BOOTCS_CFG 0x00087800 /* for pci_clk = 66 MHz */ |
| #define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE |
| |
| /* 32Mbit SRAM @0x30000000 */ |
| #define CONFIG_SYS_CS1_START 0x30000000 |
| #define CONFIG_SYS_CS1_SIZE 0x00400000 |
| #define CONFIG_SYS_CS1_CFG 0x31800 /* for pci_clk = 33 MHz */ |
| |
| /* 2 quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */ |
| #define CONFIG_SYS_CS2_START 0x80000000 |
| #define CONFIG_SYS_CS2_SIZE 0x0001000 |
| #define CONFIG_SYS_CS2_CFG 0x21800 /* for pci_clk = 33 MHz */ |
| |
| /* GPIO in @0x30400000 */ |
| #define CONFIG_SYS_CS3_START 0x30400000 |
| #define CONFIG_SYS_CS3_SIZE 0x00100000 |
| #define CONFIG_SYS_CS3_CFG 0x31800 /* for pci_clk = 33 MHz */ |
| |
| #define CONFIG_SYS_CS_BURST 0x00000000 |
| #define CONFIG_SYS_CS_DEADCYCLE 0x33333333 |
| |
| /*----------------------------------------------------------------------- |
| * USB stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_USB_OHCI |
| #define CONFIG_USB_CLOCK 0x00015555 |
| #define CONFIG_USB_CONFIG 0x00001000 |
| #define CONFIG_USB_STORAGE |
| |
| /*----------------------------------------------------------------------- |
| * IDE/ATA stuff Supports IDE harddisk |
| *----------------------------------------------------------------------- |
| */ |
| |
| #undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ |
| |
| #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ |
| #undef CONFIG_IDE_LED /* LED for ide not supported */ |
| |
| #define CONFIG_IDE_PREINIT |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */ |
| |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| #define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x0060 /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* Offset for normal register accesses */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x005C /* Offset for alternate registers */ |
| #define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */ |
| |
| #define CONFIG_ATAPI 1 |
| |
| #define CONFIG_SYS_BRIGHTNESS 0xFF /* LCD Default Brightness (255 = off) */ |
| |
| #endif /* __CONFIG_H */ |