| |
| /* |
| * (C) Copyright 2005 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #include <common.h> |
| #include <asm/processor.h> |
| #include <asm/immap_85xx.h> |
| #include <asm/processor.h> |
| #include <asm/mmu.h> |
| |
| struct sdram_conf_s { |
| unsigned long size; |
| unsigned long reg; |
| #ifdef CONFIG_TQM8548 |
| unsigned long refresh; |
| #endif /* CONFIG_TQM8548 */ |
| }; |
| |
| typedef struct sdram_conf_s sdram_conf_t; |
| |
| #ifdef CONFIG_TQM8548 |
| #ifdef CONFIG_TQM8548_AG |
| sdram_conf_t ddr_cs_conf[] = { |
| {(1024 << 20), 0x80044202, 0x0002D000}, /* 1024MB, 14x10(4) */ |
| { (512 << 20), 0x80044102, 0x0001A000}, /* 512MB, 13x10(4) */ |
| { (256 << 20), 0x80040102, 0x00014000}, /* 256MB, 13x10(4) */ |
| { (128 << 20), 0x80040101, 0x0000C000}, /* 128MB, 13x9(4) */ |
| }; |
| #else /* !CONFIG_TQM8548_AG */ |
| sdram_conf_t ddr_cs_conf[] = { |
| {(512 << 20), 0x80044102, 0x0001A000}, /* 512MB, 13x10(4) */ |
| {(256 << 20), 0x80040102, 0x00014000}, /* 256MB, 13x10(4) */ |
| {(128 << 20), 0x80040101, 0x0000C000}, /* 128MB, 13x9(4) */ |
| }; |
| #endif /* CONFIG_TQM8548_AG */ |
| #else /* !CONFIG_TQM8548 */ |
| sdram_conf_t ddr_cs_conf[] = { |
| {(512 << 20), 0x80000202}, /* 512MB, 14x10(4) */ |
| {(256 << 20), 0x80000102}, /* 256MB, 13x10(4) */ |
| {(128 << 20), 0x80000101}, /* 128MB, 13x9(4) */ |
| {( 64 << 20), 0x80000001}, /* 64MB, 12x9(4) */ |
| }; |
| #endif /* CONFIG_TQM8548 */ |
| |
| #define N_DDR_CS_CONF (sizeof(ddr_cs_conf) / sizeof(ddr_cs_conf[0])) |
| |
| int cas_latency (void); |
| static phys_size_t sdram_setup(int); |
| |
| /* |
| * Autodetect onboard DDR SDRAM on 85xx platforms |
| * |
| * NOTE: Some of the hardcoded values are hardware dependant, |
| * so this should be extended for other future boards |
| * using this routine! |
| */ |
| phys_size_t fixed_sdram(void) |
| { |
| int casl = 0; |
| phys_size_t dram_size = 0; |
| |
| casl = cas_latency(); |
| dram_size = sdram_setup(casl); |
| if ((dram_size == 0) && (casl != CONFIG_DDR_DEFAULT_CL)) { |
| /* |
| * Try again with default CAS latency |
| */ |
| printf("Problem with CAS lantency, using default CL %d/10!\n", |
| CONFIG_DDR_DEFAULT_CL); |
| dram_size = sdram_setup(CONFIG_DDR_DEFAULT_CL); |
| puts(" "); |
| } |
| return dram_size; |
| } |
| |
| static phys_size_t sdram_setup(int casl) |
| { |
| int i; |
| volatile ccsr_ddr_t *ddr = (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR); |
| #ifdef CONFIG_TQM8548 |
| volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); |
| #if defined(CONFIG_TQM8548_AG) || defined(CONFIG_TQM8548_BE) |
| volatile ccsr_local_ecm_t *ecm = (void *)(CONFIG_SYS_MPC85xx_ECM_ADDR); |
| #endif |
| #else /* !CONFIG_TQM8548 */ |
| unsigned long cfg_ddr_timing1; |
| unsigned long cfg_ddr_mode; |
| #endif /* CONFIG_TQM8548 */ |
| |
| /* |
| * Disable memory controller. |
| */ |
| ddr->cs0_config = 0; |
| ddr->sdram_cfg = 0; |
| |
| #ifdef CONFIG_TQM8548 |
| /* Timing and refresh settings for DDR2-533 and below */ |
| |
| ddr->cs0_bnds = (ddr_cs_conf[0].size - 1) >> 24; |
| ddr->cs0_config = ddr_cs_conf[0].reg; |
| ddr->timing_cfg_3 = 0x00020000; |
| |
| /* TIMING CFG 1, 533MHz |
| * PRETOACT: 4 Clocks |
| * ACTTOPRE: 12 Clocks |
| * ACTTORW: 4 Clocks |
| * CASLAT: 4 Clocks |
| * REFREC: EXT_REFREC:REFREC 53 Clocks |
| * WRREC: 4 Clocks |
| * ACTTOACT: 3 Clocks |
| * WRTORD: 2 Clocks |
| */ |
| ddr->timing_cfg_1 = 0x4C47D432; |
| |
| /* TIMING CFG 2, 533MHz |
| * ADD_LAT: 3 Clocks |
| * CPO: READLAT + 1 |
| * WR_LAT: 3 Clocks |
| * RD_TO_PRE: 2 Clocks |
| * WR_DATA_DELAY: 1/2 Clock |
| * CKE_PLS: 3 Clock |
| * FOUR_ACT: 14 Clocks |
| */ |
| ddr->timing_cfg_2 = 0x331848CE; |
| |
| /* DDR SDRAM Mode, 533MHz |
| * MRS: Extended Mode Register |
| * OUT: Outputs enabled |
| * RDQS: no |
| * DQS: enabled |
| * OCD: default state |
| * RTT: 75 Ohms |
| * Posted CAS: 3 Clocks |
| * ODS: reduced strength |
| * DLL: enabled |
| * MR: Mode Register |
| * PD: fast exit |
| * WR: 4 Clocks |
| * DLL: no DLL reset |
| * TM: normal |
| * CAS latency: 4 Clocks |
| * BT: sequential |
| * Burst length: 4 |
| */ |
| ddr->sdram_mode = 0x439E0642; |
| |
| /* DDR SDRAM Interval, 533MHz |
| * REFINT: 1040 Clocks |
| * BSTOPRE: 256 |
| */ |
| ddr->sdram_interval = (1040 << 16) | 0x100; |
| |
| /* |
| * Workaround for erratum DDR19 according to MPC8548 Device Errata |
| * document, Rev. 1: DDR IO receiver must be set to an acceptable |
| * bias point by modifying a hidden register. |
| */ |
| if (SVR_REV (get_svr ()) < 0x21) |
| gur->ddrioovcr = 0x90000000; /* enable, VSEL 1.8V */ |
| |
| /* DDR SDRAM CFG 2 |
| * FRC_SR: normal mode |
| * SR_IE: no self-refresh interrupt |
| * DLL_RST_DIS: don't care, leave at reset value |
| * DQS_CFG: differential DQS signals |
| * ODT_CFG: assert ODT to internal IOs only during reads to DRAM |
| * LVWx_CFG: don't care, leave at reset value |
| * NUM_PR: 1 refresh will be issued at a time |
| * DM_CFG: don't care, leave at reset value |
| * D_INIT: no data initialization |
| */ |
| ddr->sdram_cfg_2 = 0x04401000; |
| |
| /* DDR SDRAM MODE 2 |
| * MRS: Extended Mode Register 2 |
| */ |
| ddr->sdram_mode_2 = 0x8000C000; |
| |
| /* DDR SDRAM CLK CNTL |
| * CLK_ADJUST: 1/2 Clock 0x02000000 |
| * CLK_ADJUST: 5/8 Clock 0x02800000 |
| */ |
| ddr->sdram_clk_cntl = 0x02800000; |
| |
| /* wait for clock stabilization */ |
| asm ("sync;isync;msync"); |
| udelay (1000); |
| |
| #if defined(CONFIG_TQM8548_AG) || defined(CONFIG_TQM8548_BE) |
| /* |
| * Workaround for erratum DDR20 according to MPC8548 Device Errata |
| * document, Rev. 1: "CKE signal may not function correctly after |
| * assertion of HRESET" |
| */ |
| |
| /* 1. Configure DDR register as is done in normal DDR configuration. |
| * Do not set DDR_SDRAM_CFG[MEM_EN]. |
| * |
| * 2. Set reserved bit EEBACR[3] at offset 0x1000 |
| */ |
| ecm->eebacr |= 0x10000000; |
| |
| /* |
| * 3. Before DDR_SDRAM_CFG[MEM_EN] is set, write DDR_SDRAM_CFG_2[D_INIT] |
| * |
| * DDR_SDRAM_CFG_2: |
| * FRC_SR: normal mode |
| * SR_IE: no self-refresh interrupt |
| * DLL_RST_DIS: don't care, leave at reset value |
| * DQS_CFG: differential DQS signals |
| * ODT_CFG: assert ODT to internal IOs only during reads to DRAM |
| * LVWx_CFG: don't care, leave at reset value |
| * NUM_PR: 1 refresh will be issued at a time |
| * DM_CFG: don't care, leave at reset value |
| * D_INIT: enable data initialization |
| */ |
| ddr->sdram_cfg_2 |= 0x00000010; |
| |
| /* |
| * 4. Before DDR_SDRAM_CFG[MEM_EN] set, write D3[21] to disable data |
| * training |
| */ |
| ddr->debug[2] |= 0x00000400; |
| |
| /* |
| * 5. Wait 200 micro-seconds |
| */ |
| udelay (200); |
| |
| /* |
| * 6. Set DDR_SDRAM_CFG[MEM_EN] |
| * |
| * BTW, initialize DDR_SDRAM_CFG: |
| * MEM_EN: enabled |
| * SREN: don't care, leave at reset value |
| * ECC_EN: no error report |
| * RD_EN: no registered DIMMs |
| * SDRAM_TYPE: DDR2 |
| * DYN_PWR: no power management |
| * 32_BE: don't care, leave at reset value |
| * 8_BE: 4 beat burst |
| * NCAP: don't care, leave at reset value |
| * 2T_EN: 1T Timing |
| * BA_INTLV_CTL: no interleaving |
| * x32_EN: x16 organization |
| * PCHB8: MA[10] for auto-precharge |
| * HSE: half strength for single and 2-layer stacks |
| * (full strength for 3- and 4-layer stacks not |
| * yet considered) |
| * MEM_HALT: no halt |
| * BI: automatic initialization |
| */ |
| ddr->sdram_cfg = 0x83000008; |
| |
| /* |
| * 7. Poll DDR_SDRAM_CFG_2[D_INIT] until it is cleared by hardware |
| */ |
| asm ("sync;isync;msync"); |
| while (ddr->sdram_cfg_2 & 0x00000010) |
| asm ("eieio"); |
| |
| /* |
| * 8. Clear D3[21] to re-enable data training |
| */ |
| ddr->debug[2] &= ~0x00000400; |
| |
| /* |
| * 9. Set D2(21) to force data training to run |
| */ |
| ddr->debug[1] |= 0x00000400; |
| |
| /* |
| * 10. Poll on D2[21] until it is cleared by hardware |
| */ |
| asm ("sync;isync;msync"); |
| while (ddr->debug[1] & 0x00000400) |
| asm ("eieio"); |
| |
| /* |
| * 11. Clear reserved bit EEBACR[3] at offset 0x1000 |
| */ |
| ecm->eebacr &= ~0x10000000; |
| |
| #else /* !(CONFIG_TQM8548_AG || CONFIG_TQM8548_BE) */ |
| |
| /* DDR SDRAM CLK CNTL |
| * MEM_EN: enabled |
| * SREN: don't care, leave at reset value |
| * ECC_EN: no error report |
| * RD_EN: no register DIMMs |
| * SDRAM_TYPE: DDR2 |
| * DYN_PWR: no power management |
| * 32_BE: don't care, leave at reset value |
| * 8_BE: 4 beat burst |
| * NCAP: don't care, leave at reset value |
| * 2T_EN: 1T Timing |
| * BA_INTLV_CTL: no interleaving |
| * x32_EN: x16 organization |
| * PCHB8: MA[10] for auto-precharge |
| * HSE: half strength for single and 2-layer stacks |
| * (full strength for 3- and 4-layer stacks no yet considered) |
| * MEM_HALT: no halt |
| * BI: automatic initialization |
| */ |
| ddr->sdram_cfg = 0x83000008; |
| |
| #endif /* CONFIG_TQM8548_AG || CONFIG_TQM8548_BE */ |
| |
| asm ("sync; isync; msync"); |
| udelay (1000); |
| #else /* !CONFIG_TQM8548 */ |
| switch (casl) { |
| case 20: |
| cfg_ddr_timing1 = 0x47405331 | (3 << 16); |
| cfg_ddr_mode = 0x40020002 | (2 << 4); |
| break; |
| |
| case 25: |
| cfg_ddr_timing1 = 0x47405331 | (4 << 16); |
| cfg_ddr_mode = 0x40020002 | (6 << 4); |
| break; |
| |
| case 30: |
| default: |
| cfg_ddr_timing1 = 0x47405331 | (5 << 16); |
| cfg_ddr_mode = 0x40020002 | (3 << 4); |
| break; |
| } |
| |
| ddr->cs0_bnds = (ddr_cs_conf[0].size - 1) >> 24; |
| ddr->cs0_config = ddr_cs_conf[0].reg; |
| ddr->timing_cfg_1 = cfg_ddr_timing1; |
| ddr->timing_cfg_2 = 0x00000800; /* P9-45,may need tuning */ |
| ddr->sdram_mode = cfg_ddr_mode; |
| ddr->sdram_interval = 0x05160100; /* autocharge,no open page */ |
| ddr->err_disable = 0x0000000D; |
| |
| asm ("sync; isync; msync"); |
| udelay (1000); |
| |
| ddr->sdram_cfg = 0xc2000000; /* unbuffered,no DYN_PWR */ |
| asm ("sync; isync; msync"); |
| udelay (1000); |
| #endif /* CONFIG_TQM8548 */ |
| |
| /* |
| * get_ram_size() depends on having tlbs for the DDR, but they are |
| * not yet setup because we don't know the size. Set up a temp |
| * mapping and delete it when done. |
| */ |
| setup_ddr_tlbs(CONFIG_SYS_DDR_EARLY_SIZE_MB); |
| for (i = 0; i < N_DDR_CS_CONF; i++) { |
| ddr->cs0_config = ddr_cs_conf[i].reg; |
| |
| if (get_ram_size (0, ddr_cs_conf[i].size) == |
| ddr_cs_conf[i].size) { |
| /* |
| * size detected -> set Chip Select Bounds Register |
| */ |
| ddr->cs0_bnds = (ddr_cs_conf[i].size - 1) >> 24; |
| |
| break; |
| } |
| } |
| clear_ddr_tlbs(CONFIG_SYS_DDR_EARLY_SIZE_MB); |
| |
| #ifdef CONFIG_TQM8548 |
| if (i < N_DDR_CS_CONF) { |
| /* Adjust refresh rate for DDR2 */ |
| |
| ddr->timing_cfg_3 = ddr_cs_conf[i].refresh & 0x00070000; |
| |
| ddr->timing_cfg_1 = (ddr->timing_cfg_1 & 0xFFFF0FFF) | |
| (ddr_cs_conf[i].refresh & 0x0000F000); |
| |
| return ddr_cs_conf[i].size; |
| } |
| #endif /* CONFIG_TQM8548 */ |
| |
| /* return size if detected, else return 0 */ |
| return (i < N_DDR_CS_CONF) ? ddr_cs_conf[i].size : 0; |
| } |
| |
| #if defined(CONFIG_SYS_DRAM_TEST) |
| int testdram (void) |
| { |
| uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START; |
| uint *pend = (uint *) CONFIG_SYS_MEMTEST_END; |
| uint *p; |
| |
| printf ("SDRAM test phase 1:\n"); |
| for (p = pstart; p < pend; p++) |
| *p = 0xaaaaaaaa; |
| |
| for (p = pstart; p < pend; p++) { |
| if (*p != 0xaaaaaaaa) { |
| printf ("SDRAM test fails at: %08x\n", (uint) p); |
| return 1; |
| } |
| } |
| |
| printf ("SDRAM test phase 2:\n"); |
| for (p = pstart; p < pend; p++) |
| *p = 0x55555555; |
| |
| for (p = pstart; p < pend; p++) { |
| if (*p != 0x55555555) { |
| printf ("SDRAM test fails at: %08x\n", (uint) p); |
| return 1; |
| } |
| } |
| |
| printf ("SDRAM test passed.\n"); |
| return 0; |
| } |
| #endif |