| /* |
| * (C) Copyright 2001-2005 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #include <mpc8xx_irq.h> |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| #define CONFIG_MPC860 1 |
| #define CONFIG_MPC860T 1 |
| #define CONFIG_ICU862 1 |
| #define CONFIG_MPC862 1 |
| |
| #define CONFIG_SYS_TEXT_BASE 0x40F00000 |
| |
| #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ |
| #undef CONFIG_8xx_CONS_SMC2 |
| #undef CONFIG_8xx_CONS_NONE |
| #define CONFIG_BAUDRATE 9600 |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| |
| #ifdef CONFIG_100MHz |
| #define MPC8XX_FACT 24 /* Multiply by 24 */ |
| #define MPC8XX_XIN 4165000 /* 4.165 MHz in */ |
| #define CONFIG_8xx_GCLK_FREQ (MPC8XX_FACT * MPC8XX_XIN) |
| /* define if cant' use get_gclk_freq */ |
| #else |
| #if 1 /* for 50MHz version of processor */ |
| #define MPC8XX_FACT 12 /* Multiply by 12 */ |
| #define MPC8XX_XIN 4000000 /* 4 MHz in */ |
| #define CONFIG_8xx_GCLK_FREQ 48000000 /* define if cant use get_gclk_freq */ |
| #else /* for 80MHz version of processor */ |
| #define MPC8XX_FACT 20 /* Multiply by 20 */ |
| #define MPC8XX_XIN 4000000 /* 4 MHz in */ |
| #define CONFIG_8xx_GCLK_FREQ 80000000 /* define if cant use get_gclk_freq */ |
| #endif |
| #endif |
| |
| #if 0 |
| #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ |
| #else |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| #endif |
| |
| #define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" |
| |
| #undef CONFIG_BOOTARGS |
| #define CONFIG_BOOTCOMMAND \ |
| "bootp;" \ |
| "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ |
| "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ |
| "bootm" |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| #define CONFIG_STATUS_LED 1 /* Status LED enabled */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| |
| #undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */ |
| #define CONFIG_FEC_ENET 1 /* use FEC ethernet */ |
| #define CONFIG_MII 1 |
| #if 1 |
| #define CONFIG_SYS_DISCOVER_PHY 1 |
| #else |
| #undef CONFIG_SYS_DISCOVER_PHY |
| #endif |
| |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| |
| /* enable I2C and select the hardware/software driver */ |
| #undef CONFIG_HARD_I2C /* I2C with hardware support */ |
| #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ |
| # define CONFIG_SYS_I2C_SPEED 50000 |
| # define CONFIG_SYS_I2C_SLAVE 0xFE |
| # define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 |
| # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ |
| /* |
| * Software (bit-bang) I2C driver configuration |
| */ |
| #define PB_SCL 0x00000020 /* PB 26 */ |
| #define PB_SDA 0x00000010 /* PB 27 */ |
| |
| #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL) |
| #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA) |
| #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA) |
| #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0) |
| #define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \ |
| else immr->im_cpm.cp_pbdat &= ~PB_SDA |
| #define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \ |
| else immr->im_cpm.cp_pbdat &= ~PB_SCL |
| #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ |
| |
| #define CONFIG_SYS_EEPROM_X40430 /* Use a Xicor X40430 EEPROM */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16 bytes page write mode */ |
| |
| #define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_IDE |
| #define CONFIG_CMD_NFS |
| #define CONFIG_CMD_SNTP |
| |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x00100000 |
| |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| /*----------------------------------------------------------------------- |
| * Internal Memory Mapped Register |
| */ |
| #define CONFIG_SYS_IMMR 0xF0000000 |
| #define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024)) |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in DPRAM) |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE 0x40000000 |
| #define CONFIG_SYS_FLASH_SIZE ((uint)(16 * 1024 * 1024)) /* max 16Mbyte */ |
| |
| #define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 |
| |
| #if 0 |
| #if defined(DEBUG) |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #else |
| #define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ |
| #endif |
| #else |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #endif |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_OFFSET 0x00F40000 |
| |
| #define CONFIG_ENV_SECT_SIZE 0x40000 /* Total Size of Environment sector */ |
| #define CONFIG_ENV_SIZE 0x4000 /* Used Size of Environment Sector */ |
| #define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ |
| |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SYPCR - System Protection Control 11-9 |
| * SYPCR can only be written once after reset! |
| *----------------------------------------------------------------------- |
| * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze |
| */ |
| #if defined(CONFIG_WATCHDOG) |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) |
| #else |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SIUMCR - SIU Module Configuration 11-6 |
| *----------------------------------------------------------------------- |
| * PCMCIA config., multi-function pin tri-state |
| */ |
| #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) |
| |
| /*----------------------------------------------------------------------- |
| * TBSCR - Time Base Status and Control 11-26 |
| *----------------------------------------------------------------------- |
| * Clear Reference Interrupt Status, Timebase freezing enabled |
| */ |
| #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) |
| |
| /*----------------------------------------------------------------------- |
| * PISCR - Periodic Interrupt Status and Control 11-31 |
| *----------------------------------------------------------------------- |
| * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled |
| */ |
| #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) |
| |
| /*----------------------------------------------------------------------- |
| * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 |
| *----------------------------------------------------------------------- |
| * set the PLL, the low-power modes and the reset control (15-29) |
| */ |
| #define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ |
| PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) |
| |
| /*----------------------------------------------------------------------- |
| * SCCR - System Clock and reset Control Register 15-27 |
| *----------------------------------------------------------------------- |
| * Set clock output, timebase and RTC source and divider, |
| * power management and some other internal clocks |
| */ |
| #ifdef CONFIG_100MHz /* for 100 MHz, external bus is half CPU clock */ |
| #define SCCR_MASK 0 |
| #define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \ |
| SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \ |
| SCCR_DFLCD000 |SCCR_DFALCD00 | SCCR_EBDF01) |
| #else /* up to 50 MHz we use a 1:1 clock */ |
| #define SCCR_MASK SCCR_EBDF11 |
| #define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \ |
| SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \ |
| SCCR_DFLCD000 |SCCR_DFALCD00 ) |
| #endif /* CONFIG_100MHz */ |
| |
| /*----------------------------------------------------------------------- |
| * RCCR - RISC Controller Configuration Register 19-4 |
| *----------------------------------------------------------------------- |
| */ |
| /* +0x09C4 => DRQP = 10 (IDMA requests have lowest priority) */ |
| #define CONFIG_SYS_RCCR 0x0020 |
| |
| /*----------------------------------------------------------------------- |
| * PCMCIA stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) |
| #define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) |
| #define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) |
| #define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) |
| #define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) |
| |
| /*----------------------------------------------------------------------- |
| * PCMCIA Power Switch |
| * |
| * The ICU862 uses a TPS2205 PC-Card Power-Interface Switch to |
| * control the voltages on the PCMCIA slot which is connected to Port B |
| *----------------------------------------------------------------------- |
| */ |
| /* Output pins */ |
| #define TPS2205_VCC5 0x00008000 /* PB.16: 5V Voltage Control */ |
| #define TPS2205_VCC3 0x00004000 /* PB.17: 3V Voltage Control */ |
| #define TPS2205_VPP_PGM 0x00002000 /* PB.18: PGM Voltage Control */ |
| #define TPS2205_VPP_VCC 0x00001000 /* PB.19: VPP Voltage Control */ |
| #define TPS2205_SHDN 0x00000200 /* PB.22: Shutdown */ |
| #define TPS2205_OUTPUTS ( TPS2205_VCC5 | TPS2205_VCC3 | \ |
| TPS2205_VPP_PGM | TPS2205_VPP_VCC | \ |
| TPS2205_SHDN) |
| |
| /* Input pins */ |
| #define TPS2205_OC 0x00000100 /* PB.23: Over-Current */ |
| #define TPS2205_INPUTS ( TPS2205_OC ) |
| |
| /*----------------------------------------------------------------------- |
| * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) |
| *----------------------------------------------------------------------- |
| */ |
| |
| #define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ |
| |
| #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ |
| #undef CONFIG_IDE_LED /* LED for ide not supported */ |
| #undef CONFIG_IDE_RESET /* reset for ide not supported */ |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ |
| #define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ |
| |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR |
| |
| /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) |
| |
| /* Offset for normal register accesses */ |
| #define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) |
| |
| /* Offset for alternate registers */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 |
| |
| |
| /*----------------------------------------------------------------------- |
| * |
| *----------------------------------------------------------------------- |
| * |
| */ |
| #define CONFIG_SYS_DER 0 |
| |
| /* Because of the way the 860 starts up and assigns CS0 the |
| * entire address space, we have to set the memory controller |
| * differently. Normally, you write the option register |
| * first, and then enable the chip select by writing the |
| * base register. For CS0, you must write the base register |
| * first, followed by the option register. |
| */ |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0 and OR0 (FLASH) |
| */ |
| |
| #define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ |
| #define FLASH_BASE1_PRELIM 0x0 /* FLASH bank #1 */ |
| |
| #define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ |
| #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ |
| |
| /* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ |
| #define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) |
| |
| #define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) |
| |
| #define CONFIG_SYS_OR0_PRELIM 0xFF000954 /* Real values for the board */ |
| #define CONFIG_SYS_BR0_PRELIM 0x40000001 /* Real values for the board */ |
| |
| /* |
| * BR1 and OR1 (SDRAM) |
| */ |
| #define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank */ |
| #define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */ |
| |
| #define CONFIG_SYS_OR_TIMING_SDRAM 0x00000800 /* BIH is not set */ |
| |
| #define CONFIG_SYS_OR1_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM) |
| #define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V) |
| |
| /* |
| * Memory Periodic Timer Prescaler |
| */ |
| |
| /* periodic timer for refresh */ |
| #define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ |
| |
| /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ |
| #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ |
| #define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ |
| |
| /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ |
| #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ |
| #define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ |
| |
| /* |
| * MAMR settings for SDRAM |
| */ |
| |
| /* 8 column SDRAM */ |
| #define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
| MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ |
| MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) |
| /* 9 column SDRAM */ |
| #define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
| MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ |
| MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) |
| |
| #define CONFIG_SYS_MAMR 0x13a01114 |
| |
| #ifdef CONFIG_MPC860T |
| |
| /* Interrupt level assignments. |
| */ |
| #define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ |
| |
| #endif /* CONFIG_MPC860T */ |
| |
| |
| #endif /* __CONFIG_H */ |