include/configs/ima3-mx53.h - github/trini/u-boot - Gitiles

 /*
  * (C) Copyright 2012, Stefano Babic <sbabic@denx.de>
  *
  * Copyright (C) 2010 Freescale Semiconductor, Inc.
  *
  * Configuration settings for the MX53-EVK Freescale board.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc.
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /* SOC type must be included before imx-regs.h */
 #define CONFIG_MX53
 #include <asm/arch/imx-regs.h>
 #include <asm/arch/mx5x_pins.h>

 #define CONFIG_SYS_MX5_HCLK		24000000
 #define CONFIG_SYS_MX5_CLK32		32768

 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO

 #define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG

 #define CONFIG_OF_LIBFDT

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * 1024 * 1024)

 #define CONFIG_BOARD_EARLY_INIT_F

 /* Enable GPIOs */
 #define CONFIG_MXC_GPIO

 /* UART */
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE	UART4_BASE_ADDR

 /* MMC */
 #define CONFIG_FSL_ESDHC
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
 #define CONFIG_SYS_FSL_ESDHC_NUM	1

 #define CONFIG_MMC
 #define CONFIG_GENERIC_MMC
 #define CONFIG_DOS_PARTITION

 /* Ethernet on FEC */
 #define CONFIG_NET_MULTI
 #define CONFIG_MII

 #define CONFIG_FEC_MXC
 #define IMX_FEC_BASE			FEC_BASE_ADDR
 #define CONFIG_FEC_MXC_PHYADDR		0x01
 #define CONFIG_PHY_ADDR			CONFIG_FEC_MXC_PHYADDR
 #define CONFIG_RESET_PHY_R
 #define CONFIG_FEC_MXC_NO_ANEG
 #define CONFIG_ETHPRIME			"FEC0"

 /* SPI */
 #define CONFIG_HARD_SPI
 #define CONFIG_MXC_SPI
 #define CONFIG_DEFAULT_SPI_BUS		1
 #define CONFIG_DEFAULT_SPI_MODE		SPI_MODE_0

 /* SPI FLASH - not used for environment */
 #define CONFIG_SPI_FLASH
 #define CONFIG_SPI_FLASH_STMICRO
 #define CONFIG_SPI_FLASH_CS		(IOMUX_TO_GPIO(MX53_PIN_CSI0_D11) \
 						 << 8) | 0
 #define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
 #define CONFIG_SF_DEFAULT_SPEED		25000000

 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_CONS_INDEX		1
 #define CONFIG_BAUDRATE			115200

 /* Command definition */
 #include <config_cmd_default.h>
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_MMC
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_CMD_SPI
 #define CONFIG_CMD_SF
 #define CONFIG_CMD_GPIO

 #define CONFIG_BOOTDELAY	3

 #define CONFIG_LOADADDR		0x70800000	/* loadaddr env var */
 #define CONFIG_SYS_TEXT_BASE    0xf0001400 /* uboot in nor flash */

 #define CONFIG_ARP_TIMEOUT	200UL

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
 #define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
 #define CONFIG_SYS_PROMPT		"IMA3 MX53 U-Boot > "
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */

 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

 #define CONFIG_SYS_MEMTEST_START       0x70000000
 #define CONFIG_SYS_MEMTEST_END         0x10000

 #define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR

 #define CONFIG_SYS_HZ		1000
 #define CONFIG_CMDLINE_EDITING

 /* Physical Memory Map */
 #define CONFIG_NR_DRAM_BANKS	1
 #define PHYS_SDRAM_1		CSD0_BASE_ADDR
 #define PHYS_SDRAM_1_SIZE	(1024 * 1024 * 1024)

 #define CONFIG_SYS_SDRAM_BASE		(PHYS_SDRAM_1)
 #define CONFIG_SYS_INIT_RAM_ADDR	(IRAM_BASE_ADDR)
 #define CONFIG_SYS_INIT_RAM_SIZE	(IRAM_SIZE)

 #define CONFIG_SYS_INIT_SP_OFFSET \
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

 #define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
 #define MTDIDS_DEFAULT		"nor0=f0000000.flash"

 /* FLASH and environment organization */

 #define CONFIG_SYS_FLASH_BASE		0xF0000000
 #define CONFIG_SYS_FLASH_CFI		/* Flash is CFI conformant */
 #define CONFIG_FLASH_CFI_DRIVER		/* Use the common driver */
 #define CONFIG_FLASH_CFI_MTD		/* with MTD support */
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
 #define CONFIG_SYS_MAX_FLASH_BANKS	1
 #define CONFIG_SYS_MAX_FLASH_SECT	1024

 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE

 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)

 #define CONFIG_ENV_SIZE        (8 * 1024)
 #define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
 				CONFIG_SYS_MONITOR_LEN)
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
 					CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE

 /*
  * Default environment and default scripts
  * to update uboot and load kernel
  */

 #define HOSTNAME ima3-mx53
 #define xstr(s)	str(s)
 #define str(s)	#s

 #define CONFIG_HOSTNAME ima3-mx53
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram0 rw\0"			\
 	"addip_sta=setenv bootargs ${bootargs} "			\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"		\
 	"addip=if test -n ${ipdyn};then run addip_dyn;"			\
 		"else run addip_sta;fi\0"	\
 	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
 	"addtty=setenv bootargs ${bootargs}"				\
 		" console=${console},${baudrate}\0"			\
 	"addmisc=setenv bootargs ${bootargs} ${misc}\0"			\
 	"console=ttymxc3\0"						\
 	"loadaddr=70800000\0"						\
 	"kernel_addr_r=70800000\0"					\
 	"ramdisk_addr_r=71000000\0"					\
 	"hostname=" xstr(CONFIG_HOSTNAME) "\0"				\
 	"bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0"			\
 	"ramdisk_file=" xstr(CONFIG_HOSTNAME) "/uRamdisk\0"		\
 	"mmcargs=setenv bootargs root=${mmcroot} "			\
 		"rootfstype=${mmcrootfstype}\0"				\
 	"mmcroot=/dev/mmcblk0p3 rw\0"					\
 	"mmcboot=echo Booting from mmc ...; "				\
 		"run mmcargs addip addtty addmtd addmisc mmcload;"	\
 		"bootm\0"						\
 	"mmcload=fatload mmc ${mmcdev}:${mmcpart} "			\
 		"${loadaddr} ${uimage}\0"				\
 	"mmcrootfstype=ext3 rootwait\0"					\
 	"flash_self=run ramargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"flash_nfs=run nfsargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr}\0"				\
 	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
 		"run nfsargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr_r}\0"				\
 	"net_self_load=tftp ${ramdisk_addr_r} ${ramdisk_file};"		\
 		"tftp ${kernel_addr_r} ${bootfile}\0"			\
 	"net_self=if run net_self_load;then "				\
 		"run ramargs addip addtty addmtd addmisc;"		\
 		"bootm ${kernel_addr_r} ${ramdisk_addr_r};"		\
 		"else echo Images not loades;fi\0"			\
 	"satargs=setenv bootargs root=/dev/sda1\0"			\
 	"satafile=boot/uImage\0"					\
 	"ssdboot=echo Booting from ssd ...; "				\
 		"run satargs addip addtty addmtd addmisc;"		\
 		"sata init;ext2load sata 0:1 ${kernel_addr_r} "		\
 		"${satafile};bootm\0"					\
 	"u-boot=" xstr(CONFIG_HOSTNAME) "/u-boot.imx\0"			\
 	"uimage=uImage\0"						\
 	"load=tftp ${loadaddr} ${u-boot}\0"				\
 	"uboot_addr=0xf0001000\0"					\
 	"update=protect off 0xf0000000 +60000;"				\
 		"erase ${uboot_addr} +60000;"				\
 		"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"		\
 	"upd=if run load;then echo Updating u-boot;if run update;"	\
 		"then echo U-Boot updated;"				\
 			"else echo Error updating u-boot !;"		\
 			"echo Board without bootloader !!;"		\
 		"fi;"							\
 		"else echo U-Boot not downloaded..exiting;fi\0"		\
 	"bootcmd=run net_nfs\0"


 #define CONFIG_CMD_SATA
 #ifdef CONFIG_CMD_SATA
 	#define CONFIG_DWC_AHSATA
 	#define CONFIG_SYS_SATA_MAX_DEVICE      1
 	#define CONFIG_DWC_AHSATA_PORT_ID       0
 	#define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_BASE_ADDR
 	#define CONFIG_LBA48
 	#define CONFIG_LIBATA
 #endif

 #endif				/* __CONFIG_H */
	/*
	* (C) Copyright 2012, Stefano Babic <sbabic@denx.de>
	*
	* Copyright (C) 2010 Freescale Semiconductor, Inc.
	*
	* Configuration settings for the MX53-EVK Freescale board.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc.
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/* SOC type must be included before imx-regs.h */
	#define CONFIG_MX53
	#include <asm/arch/imx-regs.h>
	#include <asm/arch/mx5x_pins.h>

	#define CONFIG_SYS_MX5_HCLK 24000000
	#define CONFIG_SYS_MX5_CLK32 32768

	#define CONFIG_DISPLAY_CPUINFO
	#define CONFIG_DISPLAY_BOARDINFO

	#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
	#define CONFIG_SETUP_MEMORY_TAGS
	#define CONFIG_INITRD_TAG

	#define CONFIG_OF_LIBFDT

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)

	#define CONFIG_BOARD_EARLY_INIT_F

	/* Enable GPIOs */
	#define CONFIG_MXC_GPIO

	/* UART */
	#define CONFIG_MXC_UART
	#define CONFIG_MXC_UART_BASE UART4_BASE_ADDR

	/* MMC */
	#define CONFIG_FSL_ESDHC
	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
	#define CONFIG_SYS_FSL_ESDHC_NUM 1

	#define CONFIG_MMC
	#define CONFIG_GENERIC_MMC
	#define CONFIG_DOS_PARTITION

	/* Ethernet on FEC */
	#define CONFIG_NET_MULTI
	#define CONFIG_MII

	#define CONFIG_FEC_MXC
	#define IMX_FEC_BASE FEC_BASE_ADDR
	#define CONFIG_FEC_MXC_PHYADDR 0x01
	#define CONFIG_PHY_ADDR CONFIG_FEC_MXC_PHYADDR
	#define CONFIG_RESET_PHY_R
	#define CONFIG_FEC_MXC_NO_ANEG
	#define CONFIG_ETHPRIME "FEC0"

	/* SPI */
	#define CONFIG_HARD_SPI
	#define CONFIG_MXC_SPI
	#define CONFIG_DEFAULT_SPI_BUS 1
	#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0

	/* SPI FLASH - not used for environment */
	#define CONFIG_SPI_FLASH
	#define CONFIG_SPI_FLASH_STMICRO
	#define CONFIG_SPI_FLASH_CS (IOMUX_TO_GPIO(MX53_PIN_CSI0_D11) \
	<< 8) \| 0
	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
	#define CONFIG_SF_DEFAULT_SPEED 25000000

	/* allow to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_CONS_INDEX 1
	#define CONFIG_BAUDRATE 115200

	/* Command definition */
	#include <config_cmd_default.h>
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_MMC
	#define CONFIG_CMD_FAT
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_MTDPARTS
	#define CONFIG_CMD_SPI
	#define CONFIG_CMD_SF
	#define CONFIG_CMD_GPIO

	#define CONFIG_BOOTDELAY 3

	#define CONFIG_LOADADDR 0x70800000 /* loadaddr env var */
	#define CONFIG_SYS_TEXT_BASE 0xf0001400 /* uboot in nor flash */

	#define CONFIG_ARP_TIMEOUT 200UL

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
	#define CONFIG_SYS_PROMPT "IMA3 MX53 U-Boot > "
	#define CONFIG_AUTO_COMPLETE
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */

	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x70000000
	#define CONFIG_SYS_MEMTEST_END 0x10000

	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

	#define CONFIG_SYS_HZ 1000
	#define CONFIG_CMDLINE_EDITING

	/* Physical Memory Map */
	#define CONFIG_NR_DRAM_BANKS 1
	#define PHYS_SDRAM_1 CSD0_BASE_ADDR
	#define PHYS_SDRAM_1_SIZE (1024 * 1024 * 1024)

	#define CONFIG_SYS_SDRAM_BASE (PHYS_SDRAM_1)
	#define CONFIG_SYS_INIT_RAM_ADDR (IRAM_BASE_ADDR)
	#define CONFIG_SYS_INIT_RAM_SIZE (IRAM_SIZE)

	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
	#define MTDIDS_DEFAULT "nor0=f0000000.flash"

	/* FLASH and environment organization */

	#define CONFIG_SYS_FLASH_BASE 0xF0000000
	#define CONFIG_SYS_FLASH_CFI /* Flash is CFI conformant */
	#define CONFIG_FLASH_CFI_DRIVER /* Use the common driver */
	#define CONFIG_FLASH_CFI_MTD /* with MTD support */
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
	#define CONFIG_SYS_MAX_FLASH_BANKS 1
	#define CONFIG_SYS_MAX_FLASH_SECT 1024

	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_MONITOR_LEN (512 * 1024)

	#define CONFIG_ENV_SIZE (8 * 1024)
	#define CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
	CONFIG_SYS_MONITOR_LEN)
	#define CONFIG_ENV_SECT_SIZE 0x20000
	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
	CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE

	/*
	* Default environment and default scripts
	* to update uboot and load kernel
	*/

	#define HOSTNAME ima3-mx53
	#define xstr(s) str(s)
	#define str(s) #s

	#define CONFIG_HOSTNAME ima3-mx53
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram0 rw\0" \
	"addip_sta=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
	"addip=if test -n ${ipdyn};then run addip_dyn;" \
	"else run addip_sta;fi\0" \
	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
	"addtty=setenv bootargs ${bootargs}" \
	" console=${console},${baudrate}\0" \
	"addmisc=setenv bootargs ${bootargs} ${misc}\0" \
	"console=ttymxc3\0" \
	"loadaddr=70800000\0" \
	"kernel_addr_r=70800000\0" \
	"ramdisk_addr_r=71000000\0" \
	"hostname=" xstr(CONFIG_HOSTNAME) "\0" \
	"bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \
	"ramdisk_file=" xstr(CONFIG_HOSTNAME) "/uRamdisk\0" \
	"mmcargs=setenv bootargs root=${mmcroot} " \
	"rootfstype=${mmcrootfstype}\0" \
	"mmcroot=/dev/mmcblk0p3 rw\0" \
	"mmcboot=echo Booting from mmc ...; " \
	"run mmcargs addip addtty addmtd addmisc mmcload;" \
	"bootm\0" \
	"mmcload=fatload mmc ${mmcdev}:${mmcpart} " \
	"${loadaddr} ${uimage}\0" \
	"mmcrootfstype=ext3 rootwait\0" \
	"flash_self=run ramargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr}\0" \
	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
	"run nfsargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr_r}\0" \
	"net_self_load=tftp ${ramdisk_addr_r} ${ramdisk_file};" \
	"tftp ${kernel_addr_r} ${bootfile}\0" \
	"net_self=if run net_self_load;then " \
	"run ramargs addip addtty addmtd addmisc;" \
	"bootm ${kernel_addr_r} ${ramdisk_addr_r};" \
	"else echo Images not loades;fi\0" \
	"satargs=setenv bootargs root=/dev/sda1\0" \
	"satafile=boot/uImage\0" \
	"ssdboot=echo Booting from ssd ...; " \
	"run satargs addip addtty addmtd addmisc;" \
	"sata init;ext2load sata 0:1 ${kernel_addr_r} " \
	"${satafile};bootm\0" \
	"u-boot=" xstr(CONFIG_HOSTNAME) "/u-boot.imx\0" \
	"uimage=uImage\0" \
	"load=tftp ${loadaddr} ${u-boot}\0" \
	"uboot_addr=0xf0001000\0" \
	"update=protect off 0xf0000000 +60000;" \
	"erase ${uboot_addr} +60000;" \
	"cp.b ${loadaddr} ${uboot_addr} ${filesize}\0" \
	"upd=if run load;then echo Updating u-boot;if run update;" \
	"then echo U-Boot updated;" \
	"else echo Error updating u-boot !;" \
	"echo Board without bootloader !!;" \
	"fi;" \
	"else echo U-Boot not downloaded..exiting;fi\0" \
	"bootcmd=run net_nfs\0"


	#define CONFIG_CMD_SATA
	#ifdef CONFIG_CMD_SATA
	#define CONFIG_DWC_AHSATA
	#define CONFIG_SYS_SATA_MAX_DEVICE 1
	#define CONFIG_DWC_AHSATA_PORT_ID 0
	#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_BASE_ADDR
	#define CONFIG_LBA48
	#define CONFIG_LIBATA
	#endif

	#endif /* __CONFIG_H */