| # |
| # (C) Copyright 2009-2012 |
| # Wojciech Dubowik <wojciech.dubowik@neratec.com> |
| # Luka Perkov <uboot@lukaperkov.net> |
| # |
| # See file CREDITS for list of people who contributed to this |
| # project. |
| # |
| # This program is free software; you can redistribute it and/or |
| # modify it under the terms of the GNU General Public License as |
| # published by the Free Software Foundation; either version 2 of |
| # the License, or (at your option) any later version. |
| # |
| # This program is distributed in the hope that it will be useful, |
| # but WITHOUT ANY WARRANTY; without even the implied warranty of |
| # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| # GNU General Public License for more details. |
| # |
| # You should have received a copy of the GNU General Public License |
| # along with this program. If not, see <http://www.gnu.org/licenses/>. |
| # |
| # Refer docs/README.kwimage for more details about how-to configure |
| # and create kirkwood boot image |
| # |
| |
| # Boot Media configurations |
| BOOT_FROM nand |
| NAND_ECC_MODE default |
| NAND_PAGE_SIZE 0x0800 |
| |
| # SOC registers configuration using bootrom header extension |
| # Maximum KWBIMAGE_MAX_CONFIG configurations allowed |
| |
| # Configure RGMII-0 interface pad voltage to 1.8V |
| DATA 0xffd100e0 0x1b1b1b9b |
| |
| #Dram initalization for SINGLE x16 CL=5 @ 400MHz |
| DATA 0xffd01400 0x43000c30 # DDR Configuration register |
| # bit13-0: 0xc30, (3120 DDR2 clks refresh rate) |
| # bit23-14: 0x0, |
| # bit24: 0x1, enable exit self refresh mode on DDR access |
| # bit25: 0x1, required |
| # bit29-26: 0x0, |
| # bit31-30: 0x1, |
| |
| DATA 0xffd01404 0x37543000 # DDR Controller Control Low |
| # bit4: 0x0, addr/cmd in smame cycle |
| # bit5: 0x0, clk is driven during self refresh, we don't care for APX |
| # bit6: 0x0, use recommended falling edge of clk for addr/cmd |
| # bit14: 0x0, input buffer always powered up |
| # bit18: 0x1, cpu lock transaction enabled |
| # bit23-20: 0x5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 |
| # bit27-24: 0x7, CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM |
| # bit30-28: 0x3, required |
| # bit31: 0x0, no additional STARTBURST delay |
| |
| DATA 0xffd01408 0x22125451 # DDR Timing (Low) (active cycles value +1) |
| # bit3-0: TRAS lsbs |
| # bit7-4: TRCD |
| # bit11-8: TRP |
| # bit15-12: TWR |
| # bit19-16: TWTR |
| # bit20: TRAS msb |
| # bit23-21: 0x0 |
| # bit27-24: TRRD |
| # bit31-28: TRTP |
| |
| DATA 0xffd0140c 0x00000a33 # DDR Timing (High) |
| # bit6-0: TRFC |
| # bit8-7: TR2R |
| # bit10-9: TR2W |
| # bit12-11: TW2W |
| # bit31-13: 0x0, required |
| |
| DATA 0xffd01410 0x000000cc # DDR Address Control |
| # bit1-0: 00, Cs0width (x8) |
| # bit3-2: 11, Cs0size (1Gb) |
| # bit5-4: 00, Cs1width (x8) |
| # bit7-6: 11, Cs1size (1Gb) |
| # bit9-8: 00, Cs2width (nonexistent) |
| # bit11-10: 00, Cs2size (nonexistent) |
| # bit13-12: 00, Cs3width (nonexistent) |
| # bit15-14: 00, Cs3size (nonexistent) |
| # bit16: 0, Cs0AddrSel |
| # bit17: 0, Cs1AddrSel |
| # bit18: 0, Cs2AddrSel |
| # bit19: 0, Cs3AddrSel |
| # bit31-20: 0x0, required |
| |
| DATA 0xffd01414 0x00000000 # DDR Open Pages Control |
| # bit0: 0, OpenPage enabled |
| # bit31-1: 0x0, required |
| |
| DATA 0xffd01418 0x00000000 # DDR Operation |
| # bit3-0: 0x0, DDR cmd |
| # bit31-4: 0x0, required |
| |
| DATA 0xffd0141c 0x00000c52 # DDR Mode |
| # bit2-0: 0x2, BurstLen=2 required |
| # bit3: 0x0, BurstType=0 required |
| # bit6-4: 0x4, CL=5 |
| # bit7: 0x0, TestMode=0 normal |
| # bit8: 0x0, DLL reset=0 normal |
| # bit11-9: 0x6, auto-precharge write recovery ???????????? |
| # bit12: 0x0, PD must be zero |
| # bit31-13: 0x0, required |
| |
| DATA 0xffd01420 0x00000040 # DDR Extended Mode |
| # bit0: 0, DDR DLL enabled |
| # bit1: 0, DDR drive strenght normal |
| # bit2: 0, DDR ODT control lsd (disabled) |
| # bit5-3: 0x0, required |
| # bit6: 1, DDR ODT control msb, (disabled) |
| # bit9-7: 0x0, required |
| # bit10: 0, differential DQS enabled |
| # bit11: 0, required |
| # bit12: 0, DDR output buffer enabled |
| # bit31-13: 0x0, required |
| |
| DATA 0xffd01424 0x0000f17f # DDR Controller Control High |
| # bit2-0: 0x7, required |
| # bit3: 0x1, MBUS Burst Chop disabled |
| # bit6-4: 0x7, required |
| # bit7: 0x0, |
| # bit8: 0x1, add writepath sample stage, must be 1 for DDR freq >= 300MHz |
| # bit9: 0x0, no half clock cycle addition to dataout |
| # bit10: 0x0, 1/4 clock cycle skew enabled for addr/ctl signals |
| # bit11: 0x0, 1/4 clock cycle skew disabled for write mesh |
| # bit15-12: 0xf, required |
| # bit31-16: 0x0, required |
| |
| DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values) |
| DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values) |
| |
| DATA 0xffd01500 0x00000000 # CS[0]n Base address to 0x0 |
| DATA 0xffd01504 0x0ffffff1 # CS[0]n Size |
| # bit0: 0x1, Window enabled |
| # bit1: 0x0, Write Protect disabled |
| # bit3-2: 0x0, CS0 hit selected |
| # bit23-4: 0xfffff, required |
| # bit31-24: 0x0f, Size (i.e. 256MB) |
| |
| DATA 0xffd01508 0x00000000 # CS[1]n Base address to 256Mb |
| DATA 0xffd0150c 0x00000000 # CS[1]n Size, window disabled |
| |
| DATA 0xffd01514 0x00000000 # CS[2]n Size, window disabled |
| DATA 0xffd0151c 0x00000000 # CS[3]n Size, window disabled |
| |
| DATA 0xffd01494 0x00030000 # DDR ODT Control (Low) |
| # bit3-0: ODT0Rd, MODT[0] asserted during read from DRAM CS1 |
| # bit7-4: ODT0Rd, MODT[0] asserted during read from DRAM CS0 |
| # bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1 |
| # bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 |
| |
| DATA 0xffd01498 0x00000000 # DDR ODT Control (High) |
| # bit1-0: 0x0, ODT0 controlled by ODT Control (low) register above |
| # bit3-2: 0x1, ODT1 active NEVER! |
| # bit31-4: 0x0, required |
| |
| DATA 0xffd0149c 0x0000e803 # CPU ODT Control |
| DATA 0xffd01480 0x00000001 # DDR Initialization Control |
| # bit0: 0x1, enable DDR init upon this register write |
| |
| # End of Header extension |
| DATA 0x0 0x0 |