include/configs/edminiv2.h - github/trini/u-boot - Gitiles

 /*
  * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
  *
  * Based on original Kirkwood support which is
  * (C) Copyright 2009
  * Marvell Semiconductor <www.marvell.com>
  * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef _CONFIG_EDMINIV2_H
 #define _CONFIG_EDMINIV2_H

 /*
  * Version number information
  */

 #define CONFIG_IDENT_STRING	" EDMiniV2"

 /*
  * High Level Configuration Options (easy to change)
  */

 #define CONFIG_MARVELL		1
 #define CONFIG_ARM926EJS	1	/* Basic Architecture */
 #define CONFIG_FEROCEON		1	/* CPU Core subversion */
 #define CONFIG_ORION5X		1	/* SOC Family Name */
 #define CONFIG_88F5182		1	/* SOC Name */
 #define CONFIG_MACH_EDMINIV2	1	/* Machine type */

 #include <asm/arch/orion5x.h>
 /*
  * CLKs configurations
  */

 /*
  * Board-specific values for Orion5x MPP low level init:
  * - MPPs 12 to 15 are SATA LEDs (mode 5)
  * - Others are GPIO/unused (mode 3 for MPP0, mode 5 for
  *   MPP16 to MPP19, mode 0 for others
  */

 #define ORION5X_MPP0_7		0x00000003
 #define ORION5X_MPP8_15		0x55550000
 #define ORION5X_MPP16_23	0x00005555

 /*
  * Board-specific values for Orion5x GPIO low level init:
  * - GPIO3 is input (RTC interrupt)
  * - GPIO16 is Power LED control (0 = on, 1 = off)
  * - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16)
  * - GPIO18 is Power Button status (0 = Released, 1 = Pressed)
  * - GPIO19 is SATA disk power toggle (toggles on 0-to-1)
  * - GPIO22 is SATA disk power status ()
  * - GPIO23 is supply status for SATA disk ()
  * - GPIO24 is supply control for board (write 1 to power off)
  * Last GPIO is 25, further bits are supposed to be 0.
  * Enable mask has ones for INPUT, 0 for OUTPUT.
  * Default is LED ON, board ON :)
  */

 #define ORION5X_GPIO_OUT_ENABLE		0xfef4f0ca
 #define ORION5X_GPIO_OUT_VALUE		0x00000000
 #define ORION5X_GPIO_IN_POLARITY	0x000000d0

 /*
  * NS16550 Configuration
  */

 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
 #define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_TCLK
 #define CONFIG_SYS_NS16550_COM1		ORION5X_UART0_BASE

 /*
  * Serial Port configuration
  * The following definitions let you select what serial you want to use
  * for your console driver.
  */

 #define CONFIG_CONS_INDEX	1	/*Console on UART0 */
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE \
 	{ 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 }

 /*
  * FLASH configuration
  */

 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_FLASH_CFI_LEGACY
 #define CONFIG_SYS_MAX_FLASH_BANKS	1  /* max num of flash banks       */
 #define CONFIG_SYS_MAX_FLASH_SECT	11 /* max num of sects on one chip */
 #define CONFIG_SYS_FLASH_BASE		0xfff80000
 #define CONFIG_SYS_FLASH_SECTSZ \
 	{16384, 8192, 8192, 32768, \
 	 65536, 65536, 65536, 65536, 65536, 65536, 65536}

 /* auto boot */
 #define CONFIG_BOOTDELAY	3	/* default enable autoboot */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs  */
 #define CONFIG_INITRD_TAG	1	/* enable INITRD tag */
 #define CONFIG_SETUP_MEMORY_TAGS 1	/* enable memory tag */

 #define	CONFIG_SYS_PROMPT	"EDMiniV2> "	/* Command Prompt */
 #define	CONFIG_SYS_CBSIZE	1024	/* Console I/O Buff Size */
 #define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE \
 		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
 /*
  * Commands configuration - using default command set for now
  */
 #include <config_cmd_default.h>
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_USB

 /*
  * Network
  */

 #ifdef CONFIG_CMD_NET
 #define CONFIG_MVGBE				/* Enable Marvell GbE Driver */
 #define CONFIG_MVGBE_PORTS	{1}		/* enable port 0 only */
 #define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION	/* don't randomize MAC */
 #define CONFIG_PHY_BASE_ADR	0x8
 #define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
 #define CONFIG_NETCONSOLE	/* include NetConsole support   */
 #define	CONFIG_MII		/* expose smi ove miiphy interface */
 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
 #define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
 #endif

 /*
  * IDE
  */
 #ifdef CONFIG_CMD_IDE
 #define __io
 #define CONFIG_IDE_PREINIT
 #define CONFIG_DOS_PARTITION
 #define CONFIG_CMD_EXT2
 /* ED Mini V has an IDE-compatible SATA connector for port 1 */
 #define CONFIG_MVSATA_IDE
 #define CONFIG_MVSATA_IDE_USE_PORT1
 /* Needs byte-swapping for ATA data register */
 #define CONFIG_IDE_SWAP_IO
 /* Data, registers and alternate blocks are at the same offset */
 #define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
 #define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
 #define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
 /* Each 8-bit ATA register is aligned to a 4-bytes address */
 #define CONFIG_SYS_ATA_STRIDE		4
 /* Controller supports 48-bits LBA addressing */
 #define CONFIG_LBA48
 /* A single bus, a single device */
 #define CONFIG_SYS_IDE_MAXBUS		1
 #define CONFIG_SYS_IDE_MAXDEVICE	1
 /* ATA registers base is at SATA controller base */
 #define CONFIG_SYS_ATA_BASE_ADDR	ORION5X_SATA_BASE
 /* ATA bus 0 is orion5x port 1 on ED Mini V2 */
 #define CONFIG_SYS_ATA_IDE0_OFFSET	ORION5X_SATA_PORT1_OFFSET
 /* end of IDE defines */
 #endif /* CMD_IDE */

 /*
  * Common USB/EHCI configuration
  */
 #ifdef CONFIG_CMD_USB
 #define CONFIG_USB_EHCI		/* Enable EHCI USB support */
 #define CONFIG_USB_EHCI_MARVELL
 #define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
 #define CONFIG_USB_STORAGE
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION
 #define CONFIG_SUPPORT_VFAT
 #endif /* CONFIG_CMD_USB */

 /*
  * I2C related stuff
  */
 #ifdef CONFIG_CMD_I2C
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MVTWSI
 #define CONFIG_I2C_MVTWSI_BASE		ORION5X_TWSI_BASE
 #define CONFIG_SYS_I2C_SLAVE		0x0
 #define CONFIG_SYS_I2C_SPEED		100000
 #endif

 /*
  *  Environment variables configurations
  */
 #define CONFIG_ENV_IS_IN_FLASH		1
 #define CONFIG_ENV_SECT_SIZE		0x2000	/* 16K */
 #define CONFIG_ENV_SIZE			0x2000
 #define CONFIG_ENV_OFFSET		0x4000	/* env starts here */

 /*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN	(1024 * 256) /* 256kB for malloc() */

 /*
  * Other required minimal configurations
  */
 #define CONFIG_CONSOLE_INFO_QUIET	/* some code reduction */
 #define CONFIG_ARCH_CPU_INIT		/* call arch_cpu_init() */
 #define CONFIG_ARCH_MISC_INIT		/* call arch_misc_init() */
 #define CONFIG_DISPLAY_CPUINFO		/* Display cpu info */
 #define CONFIG_NR_DRAM_BANKS		1

 #define CONFIG_SYS_LOAD_ADDR		0x00800000
 #define CONFIG_SYS_MEMTEST_START	0x00400000
 #define CONFIG_SYS_MEMTEST_END		0x007fffff
 #define CONFIG_SYS_RESET_ADDRESS	0xffff0000
 #define CONFIG_SYS_MAXARGS		16

 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER

 /* Enable command line editing */
 #define CONFIG_CMDLINE_EDITING

 /* provide extensive help */
 #define CONFIG_SYS_LONGHELP

 /* additions for new relocation code, must be added to all boards */
 #define CONFIG_SYS_SDRAM_BASE		0
 #define CONFIG_SYS_INIT_SP_ADDR	\
 	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)

 #endif /* _CONFIG_EDMINIV2_H */
	/*
	* Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
	*
	* Based on original Kirkwood support which is
	* (C) Copyright 2009
	* Marvell Semiconductor <www.marvell.com>
	* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef _CONFIG_EDMINIV2_H
	#define _CONFIG_EDMINIV2_H

	/*
	* Version number information
	*/

	#define CONFIG_IDENT_STRING " EDMiniV2"

	/*
	* High Level Configuration Options (easy to change)
	*/

	#define CONFIG_MARVELL 1
	#define CONFIG_ARM926EJS 1 /* Basic Architecture */
	#define CONFIG_FEROCEON 1 /* CPU Core subversion */
	#define CONFIG_ORION5X 1 /* SOC Family Name */
	#define CONFIG_88F5182 1 /* SOC Name */
	#define CONFIG_MACH_EDMINIV2 1 /* Machine type */

	#include <asm/arch/orion5x.h>
	/*
	* CLKs configurations
	*/

	/*
	* Board-specific values for Orion5x MPP low level init:
	* - MPPs 12 to 15 are SATA LEDs (mode 5)
	* - Others are GPIO/unused (mode 3 for MPP0, mode 5 for
	* MPP16 to MPP19, mode 0 for others
	*/

	#define ORION5X_MPP0_7 0x00000003
	#define ORION5X_MPP8_15 0x55550000
	#define ORION5X_MPP16_23 0x00005555

	/*
	* Board-specific values for Orion5x GPIO low level init:
	* - GPIO3 is input (RTC interrupt)
	* - GPIO16 is Power LED control (0 = on, 1 = off)
	* - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16)
	* - GPIO18 is Power Button status (0 = Released, 1 = Pressed)
	* - GPIO19 is SATA disk power toggle (toggles on 0-to-1)
	* - GPIO22 is SATA disk power status ()
	* - GPIO23 is supply status for SATA disk ()
	* - GPIO24 is supply control for board (write 1 to power off)
	* Last GPIO is 25, further bits are supposed to be 0.
	* Enable mask has ones for INPUT, 0 for OUTPUT.
	* Default is LED ON, board ON :)
	*/

	#define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca
	#define ORION5X_GPIO_OUT_VALUE 0x00000000
	#define ORION5X_GPIO_IN_POLARITY 0x000000d0

	/*
	* NS16550 Configuration
	*/

	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE (-4)
	#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
	#define CONFIG_SYS_NS16550_COM1 ORION5X_UART0_BASE

	/*
	* Serial Port configuration
	* The following definitions let you select what serial you want to use
	* for your console driver.
	*/

	#define CONFIG_CONS_INDEX 1 /Console on UART0 /
	#define CONFIG_BAUDRATE 115200
	#define CONFIG_SYS_BAUDRATE_TABLE \
	{ 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 }

	/*
	* FLASH configuration
	*/

	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_FLASH_CFI_LEGACY
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 11 /* max num of sects on one chip */
	#define CONFIG_SYS_FLASH_BASE 0xfff80000
	#define CONFIG_SYS_FLASH_SECTSZ \
	{16384, 8192, 8192, 32768, \
	65536, 65536, 65536, 65536, 65536, 65536, 65536}

	/* auto boot */
	#define CONFIG_BOOTDELAY 3 /* default enable autoboot */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
	#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
	#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */

	#define CONFIG_SYS_PROMPT "EDMiniV2> " /* Command Prompt */
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
	+sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
	/*
	* Commands configuration - using default command set for now
	*/
	#include <config_cmd_default.h>
	#define CONFIG_CMD_IDE
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_USB

	/*
	* Network
	*/

	#ifdef CONFIG_CMD_NET
	#define CONFIG_MVGBE /* Enable Marvell GbE Driver */
	#define CONFIG_MVGBE_PORTS {1} /* enable port 0 only */
	#define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION /* don't randomize MAC */
	#define CONFIG_PHY_BASE_ADR 0x8
	#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
	#define CONFIG_NETCONSOLE /* include NetConsole support */
	#define CONFIG_MII /* expose smi ove miiphy interface */
	#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
	#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
	#endif

	/*
	* IDE
	*/
	#ifdef CONFIG_CMD_IDE
	#define __io
	#define CONFIG_IDE_PREINIT
	#define CONFIG_DOS_PARTITION
	#define CONFIG_CMD_EXT2
	/* ED Mini V has an IDE-compatible SATA connector for port 1 */
	#define CONFIG_MVSATA_IDE
	#define CONFIG_MVSATA_IDE_USE_PORT1
	/* Needs byte-swapping for ATA data register */
	#define CONFIG_IDE_SWAP_IO
	/* Data, registers and alternate blocks are at the same offset */
	#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
	#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
	#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
	/* Each 8-bit ATA register is aligned to a 4-bytes address */
	#define CONFIG_SYS_ATA_STRIDE 4
	/* Controller supports 48-bits LBA addressing */
	#define CONFIG_LBA48
	/* A single bus, a single device */
	#define CONFIG_SYS_IDE_MAXBUS 1
	#define CONFIG_SYS_IDE_MAXDEVICE 1
	/* ATA registers base is at SATA controller base */
	#define CONFIG_SYS_ATA_BASE_ADDR ORION5X_SATA_BASE
	/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
	#define CONFIG_SYS_ATA_IDE0_OFFSET ORION5X_SATA_PORT1_OFFSET
	/* end of IDE defines */
	#endif /* CMD_IDE */

	/*
	* Common USB/EHCI configuration
	*/
	#ifdef CONFIG_CMD_USB
	#define CONFIG_USB_EHCI /* Enable EHCI USB support */
	#define CONFIG_USB_EHCI_MARVELL
	#define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
	#define CONFIG_USB_STORAGE
	#define CONFIG_DOS_PARTITION
	#define CONFIG_ISO_PARTITION
	#define CONFIG_SUPPORT_VFAT
	#endif /* CONFIG_CMD_USB */

	/*
	* I2C related stuff
	*/
	#ifdef CONFIG_CMD_I2C
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MVTWSI
	#define CONFIG_I2C_MVTWSI_BASE ORION5X_TWSI_BASE
	#define CONFIG_SYS_I2C_SLAVE 0x0
	#define CONFIG_SYS_I2C_SPEED 100000
	#endif

	/*
	* Environment variables configurations
	*/
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_SECT_SIZE 0x2000 /* 16K */
	#define CONFIG_ENV_SIZE 0x2000
	#define CONFIG_ENV_OFFSET 0x4000 /* env starts here */

	/*
	* Size of malloc() pool
	*/
	#define CONFIG_SYS_MALLOC_LEN (1024 * 256) /* 256kB for malloc() */

	/*
	* Other required minimal configurations
	*/
	#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
	#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
	#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
	#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
	#define CONFIG_NR_DRAM_BANKS 1

	#define CONFIG_SYS_LOAD_ADDR 0x00800000
	#define CONFIG_SYS_MEMTEST_START 0x00400000
	#define CONFIG_SYS_MEMTEST_END 0x007fffff
	#define CONFIG_SYS_RESET_ADDRESS 0xffff0000
	#define CONFIG_SYS_MAXARGS 16

	/* Use the HUSH parser */
	#define CONFIG_SYS_HUSH_PARSER

	/* Enable command line editing */
	#define CONFIG_CMDLINE_EDITING

	/* provide extensive help */
	#define CONFIG_SYS_LONGHELP

	/* additions for new relocation code, must be added to all boards */
	#define CONFIG_SYS_SDRAM_BASE 0
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)

	#endif /* _CONFIG_EDMINIV2_H */