rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/include/configs/ATUM8548.h b/include/configs/ATUM8548.h
index 8efea00..2450adb 100644
--- a/include/configs/ATUM8548.h
+++ b/include/configs/ATUM8548.h
@@ -79,23 +79,23 @@
#define CONFIG_CMD_SDRAM 1 /* SDRAM DIMM SPD info printout */
#define CONFIG_ENABLE_36BIT_PHYS 1
-#undef CFG_DRAM_TEST
-#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00400000
+#undef CONFIG_SYS_DRAM_TEST
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
-#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
#define PCI_SPEED 33333000 /* CPLD currenlty does not have PCI setup info */
-#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
-#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)
-#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
+#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
+#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000)
+#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
/* DDR Setup */
#define CONFIG_FSL_DDR2
@@ -107,8 +107,8 @@
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define CFG_DDR_SDRAM_BASE 0x00000000
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM
#define CONFIG_NUM_DDR_CONTROLLERS 1
@@ -119,15 +119,15 @@
#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
/* Manually set up DDR parameters */
-#define CFG_SDRAM_SIZE 1024 /* DDR is 1024MB */
-#define CFG_DDR_CS0_BNDS 0x0000000f /* 0-1024 */
-#define CFG_DDR_CS0_CONFIG 0x80000102
-#define CFG_DDR_TIMING_0 0x00260802
-#define CFG_DDR_TIMING_1 0x38355322
-#define CFG_DDR_TIMING_2 0x039048c7
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
-#define CFG_DDR_MODE 0x00000432
-#define CFG_DDR_INTERVAL 0x05150100
+#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f /* 0-1024 */
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80000102
+#define CONFIG_SYS_DDR_TIMING_0 0x00260802
+#define CONFIG_SYS_DDR_TIMING_1 0x38355322
+#define CONFIG_SYS_DDR_TIMING_2 0x039048c7
+#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+#define CONFIG_SYS_DDR_MODE 0x00000432
+#define CONFIG_SYS_DDR_INTERVAL 0x05150100
#define DDR_SDRAM_CFG 0x43000000
#undef CONFIG_CLOCKS_IN_MHZ
@@ -164,63 +164,63 @@
* 1111 1000 0000 0000 0000 1110 0110 0101 = f8000E65 ORx
*/
-#define CFG_BOOT_BLOCK 0xf8000000 /* boot TLB block */
-#define CFG_FLASH_BASE CFG_BOOT_BLOCK /* start of FLASH 128M */
+#define CONFIG_SYS_BOOT_BLOCK 0xf8000000 /* boot TLB block */
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK /* start of FLASH 128M */
-#define CFG_BR0_PRELIM 0xf8001001
+#define CONFIG_SYS_BR0_PRELIM 0xf8001001
-#define CFG_OR0_PRELIM 0xf8000E65
+#define CONFIG_SYS_OR0_PRELIM 0xf8000E65
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 512000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 8000 /* Flash Write Timeout (ms) */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 512000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 8000 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#define CONFIG_FLASH_CFI_DRIVER 1
-#define CFG_FLASH_CFI 1
-#define CFG_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI 1
+#define CONFIG_SYS_FLASH_EMPTY_INFO
/*
* Flash on the LocalBus
*/
-#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
+#define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
/* Memory */
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */
+#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/* pass open firmware flat tree */
@@ -233,41 +233,41 @@
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_EEPROM_ADDR 0x57
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
/*
* General PCI
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
-#define CFG_PCI_PHYS 0x80000000 /* 1G PCI TLB */
+#define CONFIG_SYS_PCI_PHYS 0x80000000 /* 1G PCI TLB */
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0x00000000
-#define CFG_PCI1_IO_PHYS 0xe2000000
-#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
#ifdef CONFIG_PCI2
-#define CFG_PCI2_MEM_BASE 0xC0000000
-#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI2_IO_BASE 0x00000000
-#define CFG_PCI2_IO_PHYS 0xe2800000
-#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCI2_MEM_BASE 0xC0000000
+#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
+#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS 0xe2800000
+#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */
#endif
#ifdef CONFIG_PCIE1
-#define CFG_PCIE1_MEM_BASE 0xa0000000
-#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
-#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCIE1_IO_BASE 0x00000000
-#define CFG_PCIE1_IO_PHYS 0xe3000000
-#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */
+#define CONFIG_SYS_PCIE1_MEM_BASE 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */
#endif
@@ -288,9 +288,9 @@
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
/* PCI view of System Memory */
-#define CFG_PCI_MEMORY_BUS 0x00000000
-#define CFG_PCI_MEMORY_PHYS 0x00000000
-#define CFG_PCI_MEMORY_SIZE 0x80000000
+#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000
+#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000
+#define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000
#endif /* CONFIG_PCI */
@@ -334,12 +334,12 @@
* Environment
*/
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* BOOTP options
@@ -369,25 +369,25 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions